eWON Family - eWON Support

More documents

Recommendations

Info

10.9 GSM modem Led behavior Figure 142: GSM level display on led The modem led default behavior is to go solid red while PPP Is established and off otherwise. If this option is selected, the modem led will display the signal level as described here: The led must display 2 informations: • if the modem is connected. • the signal reception level. General Reference Guide Appendix The representation uses an 8 seconds pattern, the first 4 seconds display the signal level and the last 4 seconds the connection state. Signal level: the signal level is displayed 4 times. The led goes on between 100msec to 900msec according to the signal level. Then the blink is repeated 3 more times. Connection state: for the last 4 seconds, the led is ON if connection is established (PPP connection established). The led is OFF if there is no ongoing connection. REM: the signal level displayed here is a rough indication, the exact level can be read from the modem configuration page in the <strong>eWON</strong>. Connected Low signal level Connected High signal level Disconnected High signal level Table 190: GSM Level display patterns RG-001-0-EN ver 1.6 <strong>eWON</strong>® - 22/06/2009 - ©ACT'L sa Page 205
Page 1 and 2:
eWON Family 500, 2001, 4001, 2101,
Page 3 and 4:
Table of content 5.4.3 Tag name con
Page 5 and 6:
Table of content 8.3.8 $dtSE [Scrip
Page 7 and 8:
2 The eWON login page 2.1 Access fr
Page 9 and 10:
3.2 Users Setup The Users Setup pag
Page 11 and 12:
3.2.5 User’s directory restrictio
Page 13 and 14:
3.3 System Setup General Reference
Page 15 and 16:
3.3.1.2 Alarms (globals parameters)
Page 17 and 18:
3.3.2 Net services setup General Re
Page 19 and 20:
General Reference Guide eWON Config
Page 21 and 22:
Control Description Enable NTP cloc
Page 23 and 24:
The parameters for Alarm traps are
Page 25 and 26:
Control Description General Referen
Page 27 and 28:
3.3.4 COM Setup section Warning: de
Page 29 and 30:
3.3.4.1.1.2 Modem configuration (GS
Page 31 and 32:
3.3.4.1.1.3 Modem configuration (IS
Page 33 and 34:
3.3.4.1.1.5 ADSL interface General
Page 35 and 36:
3.3.4.2.1 Ethernet LAN (& WAN) 3.3.
Page 37 and 38:
Page 39 and 40:
3.3.4.2.2.2 Outgoing Global paramet
Page 41 and 42:
Page 43 and 44:
3.3.4.2.4 VPN General Reference Gui
Page 45 and 46:
VPN between two eWONs General Refer
Page 47 and 48:
VPN with an ENDIAN Server You can f
Page 49 and 50:
Ethernet WAN Connection - Disconnec
Page 51 and 52:
3.3.4.3 Networking Config 3.3.4.3.1
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
3.3.4.3.6 Proxy 3.3.4.3.6.1 Why a p
Page 61 and 62:
3.3.4.3.7 Security You can define t
Page 63 and 64:
3.3.4.4.2 Default Config General Re
Page 65 and 66:
Page 67 and 68:
3.3.4.5.3 Features General Referenc
Page 69 and 70:
3.4.1.2 Tags validation General Ref
Page 71 and 72:
3.4.2.1 Tag main edit window Genera
Page 73 and 74:
Control Description Tag name Tag De
Page 75 and 76:
Page 77 and 78:
3.4.2.2.1 Email on alarm configurat
Page 79 and 80:
Examples: General Reference Guide e
Page 81 and 82:
3.7 Script Setup General Reference
Page 83 and 84:
3.7.2 The Script control link Gener
Page 85 and 86:
4 Configuring the eWON by a file up
Page 87 and 88:
5.2.1 IO Server Clear To avoid the
Page 89 and 90:
5.3 Modbus IO server 5.3.1 Introduc
Page 91 and 92:
Parameter name Description PreDelay
Page 93 and 94:
General Reference Guide IO Servers
Page 95 and 96:
5.4 NETMPI IO Server 5.4.1 Introduc
Page 97 and 98:
5.5 UNITE IO Server 5.5.1 Introduct
Page 99 and 100:
5.5.3.1 Value Name Value name follo
Page 101 and 102:
5.6 DF1 IO Server 5.6.1 Introductio
Page 103 and 104:
General Reference Guide IO Servers
Page 105 and 106:
5.6.3.1.4 Status File Items Status
Page 107 and 108:
5.7 FINS IO Server 5.7.1 Introducti
Page 109 and 110:
5.7.2.3 Gateway Configuration The f
Page 111 and 112:
5.8 S5-AS511 IO Server 5.8.1 Introd
Page 113 and 114:
• Status register: General Refere
Page 115 and 116:
5.9.2.1 Communication Setup General
Page 117 and 118:
5.9.3.1 ValueName ValueName follows
Page 119 and 120:
Example of use of SN_LO and SN_HI i
Page 121 and 122:
5.10.2.2.1 ENERGY TAGS The followin
Page 123 and 124:
5.10.2.3.2 PT100 input AI5 and AI6
Page 125 and 126:
5.11 MEM IO Server 5.11.1 Introduct
Page 127 and 128:
Baud Rate 5.12.2.2 Topic configurat
Page 129 and 130:
Examples • Bit access modifier: G
Page 131 and 132:
5.13 S7-200 (PPI - ISOTCP) 5.13.1 I
Page 133 and 134:
5.13.2.4 Topic configuration Genera
Page 135 and 136:
Page 137 and 138:
5.14.1.1.2 Topic configuration Gene
Page 139 and 140:
Note: The Modifier can by omitted,
Page 141 and 142:
5.15 MITSUBISHI FX IO Server 5.15.1
Page 143 and 144:
5.15.3.1 Value Name The syntax is t
Page 145 and 146:
5.16 SNMP IO Server 5.16.1 Introduc
Page 147 and 148:
Page 149 and 150:
6.1 Real-time screen General Refere
Page 151 and 152:
General Reference Guide Monitoring
Page 153 and 154:
6.4 Real time Alarm screen Figure 1
Page 155 and 156: 6.6 Files transfer This link gives
Page 157 and 158: General Reference Guide Monitoring
Page 159 and 160: 6.7.2.1 Memory Information 6.7.2.2
Page 161 and 162: 6.7.2.5 Info 6.7.3 Scheduled Action
Page 163 and 164: 6.7.4.2 Activate Energy debug mode
Page 165 and 166: 7 Retrieving Data from eWON 7.1 Lis
Page 167 and 168: 7.3 FTP transfer FTP stands for the
Page 169 and 170: 8.2 Export fields syntax definition
Page 171 and 172: 8.2.4 $ut [Update Time] General Ref
Page 173 and 174: $ft General Reference Guide Export
Page 175 and 176: For fixed interval, $in parameter m
Page 177 and 178: 8.3.4 $dtAH [Alarm History] General
Page 179 and 180: 8.3.6 $dtEV [EVent file] 8.3.6.1 Ex
Page 181 and 182: 8.3.8 $dtSE [Script Expression] 8.3
Page 183 and 184: General Reference Guide Export Bloc
Page 185 and 186: General Reference Guide Export Bloc
Page 187 and 188: 8.3.11 $dtSV General Reference Guid
Page 189 and 190: 8.3.14 $dtSC General Reference Guid
Page 191 and 192: 8.3.16 $dtTR [TAR file] 8.3.16.1 Ex
Page 193 and 194: 9 Upgrading the eWON firmware 9.1 P
Page 195 and 196: Click on the Finish Button when the
Page 197 and 198: General Reference Guide Upgrading t
Page 199 and 200: 9.5 Upgrade Bootloader (to upgrade
Page 201 and 202: 10.2.2 Non-volatile configuration T
Page 203 and 204: If an error is detected during the
Page 205: 10.7 Duplicate IP detection (User L
show all

eWON Family - eWON Support

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?