eWON Family - eWON Support

More documents

Recommendations

Info

5.4.3.1 ValueName (*) Important: See “Tags are stored as Float” on page 67 • Bit access modifier: General Reference Guide IO Servers Configuration In any of the above items, it is possible to access a single bit (except for float items). #x must be appended to the Value Name. (Bit index goes from 0..31) The syntax can be used for reading bits and for writing them as well. Example: DB1W13#3 represents bit 3 of W13 in DB 1 REM: Bit index range depends on a referenced item (for W, bit index maximum value is 15) • Status register: The STATUS Tag is a special Tag that returns information about the current state of the communication for a given device. As for other Tags, the status Tag ValueName is composed of: Status, Global Device Address • You can define a status Tag for each PLC used. • If you use the status address, the Tag must be configured as analog. 0 DBxBy Data block x Byte offset y (0-255) DBxWy Data block x Word offset y (0 - 65535) DBxFy Data block x Float offset y (+-3.4e38) DBxDy Data block x DWord offset y (-2147483648->2147483647) (*) MxB Memento x as byte MxW Memento x as word MxF Memento x as real MxD Memento x as double (*) Tx Timer x (0-65535) Cx Counter x (0-65535) Table 67: value names for NETMPI addresses Communication not initialized. Status UNKNOWN. If no Tag is polled on that device address, the communication status is unknown. 1 Communication OK. 2 Communication NOT OK. Table 68: Tag Status meaning 5.4.3.2 Device Address The device address is either appended to the ValueName in the Item Name definition, or entered in the Topic global address fields. The device address is composed of: RemoteStationAddress,eLinkIpAddress: • RemoteStationAddress: is the PLC’s MPI address • eLinkIpAddress: is the eLINK IP address. Important: If the PLC address is defined at the Topic level, it can be omitted in the Tag definition. In that case the Tag name will only contain the "ValueName". If the PLC address is specified at the Topic level, it will replace any address defined Tag by Tag. RG-001-0-EN ver 1.6 eWON® - 22/06/2009 - ©ACT'L sa Page 95
5.5 UNITE IO Server 5.5.1 Introduction General Reference Guide IO Servers Configuration The eWON RS485 link can be configured as an UNITELWAY SLAVE INTERFACE. When the BaudRate in the UNITE IO Server is set to a value different than "Disabled", the Unitelway slave module in the eWON will be enabled. This Unitelway slave provides 2 features: • Poll items in a Unitelway capable device. The device can be the Unitelway master itself or a device addressable through the Unitelway master on the XWay network. • Forward XIP requests from TCP/IP XIP to Unitelway bus and thus, act as a gateway between XIP and Unitelway. Using that feature, it is possible to access a PLC connected to the eWON’s Unitelway link by connecting PL7PRO using the XIP driver started with the eWON IP address as destination. 5.5.2 Setup 5.5.2.1 Communication Setup Figure 79: XWAY-UNITELWAY configuration If more than one Serial port are available, you must choose on which COM the Unitelway request will be sent. Baud Rate Select the baud rate applying to your industrial network Parity Stop Bit(s) Number of stop bits Master Response Timeout The parity to apply: none / odd / even. This field is set by default to Odd, as in the main cases in a typical UniTE topology. However, the eWON allows you to define a different parity type (Even or None), in case this is needful to comply with your industrial network installations. Maximum time the eWON will wait for a valid message from the Unitelway master. This value can be critical for a correct operation, depending on the responsiveness of the master. A value of 1000 should be selected to guarantee a correct operation. Rx message timeout (MSEC) Maximum time between a request is posted and the response is received Tx message timeout (MSEC) Maximum time for a request to be sent Force UnitelWay V2 ADO Xway Network Station If checked, the eWON will initiate a communication in V2 with the devices. When used with a TSX PLC, this check box can be left unchecked. Link address base. The eWON will respond to AD0 and AD0+1 on the Unitelway link. The eWON will act as an Unitelway slave, it will respond to 2 consecutive link addresses AD0 and AD0+1, doing this improves the throughput of data across the eWON when acting as a gateway. Address of the eWON on the XWAY network. When acting as an XIP to Unitelway gateway, the eWON will only respond the XWay network station defined here. Any XIP frame addressed to another network station will be ignored. Table 69: XWAY communication setup controls RG-001-0-EN ver 1.6 eWON® - 22/06/2009 - ©ACT'L sa Page 96
Page 1 and 2:
eWON Family 500, 2001, 4001, 2101,
Page 3 and 4:
Table of content 5.4.3 Tag name con
Page 5 and 6:
Table of content 8.3.8 $dtSE [Scrip
Page 7 and 8:
2 The eWON login page 2.1 Access fr
Page 9 and 10:
3.2 Users Setup The Users Setup pag
Page 11 and 12:
3.2.5 User’s directory restrictio
Page 13 and 14:
3.3 System Setup General Reference
Page 15 and 16:
3.3.1.2 Alarms (globals parameters)
Page 17 and 18:
3.3.2 Net services setup General Re
Page 19 and 20:
General Reference Guide eWON Config
Page 21 and 22:
Control Description Enable NTP cloc
Page 23 and 24:
The parameters for Alarm traps are
Page 25 and 26:
Control Description General Referen
Page 27 and 28:
3.3.4 COM Setup section Warning: de
Page 29 and 30:
3.3.4.1.1.2 Modem configuration (GS
Page 31 and 32:
3.3.4.1.1.3 Modem configuration (IS
Page 33 and 34:
3.3.4.1.1.5 ADSL interface General
Page 35 and 36:
3.3.4.2.1 Ethernet LAN (& WAN) 3.3.
Page 37 and 38:
Page 39 and 40:
3.3.4.2.2.2 Outgoing Global paramet
Page 41 and 42:
Page 43 and 44:
3.3.4.2.4 VPN General Reference Gui
Page 45 and 46: VPN between two eWONs General Refer
Page 47 and 48: VPN with an ENDIAN Server You can f
Page 49 and 50: Ethernet WAN Connection - Disconnec
Page 51 and 52: 3.3.4.3 Networking Config 3.3.4.3.1
Page 53 and 54: General Reference Guide eWON Config
Page 59 and 60: 3.3.4.3.6 Proxy 3.3.4.3.6.1 Why a p
Page 61 and 62: 3.3.4.3.7 Security You can define t
Page 63 and 64: 3.3.4.4.2 Default Config General Re
Page 67 and 68: 3.3.4.5.3 Features General Referenc
Page 69 and 70: 3.4.1.2 Tags validation General Ref
Page 71 and 72: 3.4.2.1 Tag main edit window Genera
Page 73 and 74: Control Description Tag name Tag De
Page 77 and 78: 3.4.2.2.1 Email on alarm configurat
Page 79 and 80: Examples: General Reference Guide e
Page 81 and 82: 3.7 Script Setup General Reference
Page 83 and 84: 3.7.2 The Script control link Gener
Page 85 and 86: 4 Configuring the eWON by a file up
Page 87 and 88: 5.2.1 IO Server Clear To avoid the
Page 89 and 90: 5.3 Modbus IO server 5.3.1 Introduc
Page 91 and 92: Parameter name Description PreDelay
Page 93 and 94: General Reference Guide IO Servers
Page 95: 5.4 NETMPI IO Server 5.4.1 Introduc
Page 99 and 100: 5.5.3.1 Value Name Value name follo
Page 101 and 102: 5.6 DF1 IO Server 5.6.1 Introductio
Page 103 and 104: General Reference Guide IO Servers
Page 105 and 106: 5.6.3.1.4 Status File Items Status
Page 107 and 108: 5.7 FINS IO Server 5.7.1 Introducti
Page 109 and 110: 5.7.2.3 Gateway Configuration The f
Page 111 and 112: 5.8 S5-AS511 IO Server 5.8.1 Introd
Page 113 and 114: • Status register: General Refere
Page 115 and 116: 5.9.2.1 Communication Setup General
Page 117 and 118: 5.9.3.1 ValueName ValueName follows
Page 119 and 120: Example of use of SN_LO and SN_HI i
Page 121 and 122: 5.10.2.2.1 ENERGY TAGS The followin
Page 123 and 124: 5.10.2.3.2 PT100 input AI5 and AI6
Page 125 and 126: 5.11 MEM IO Server 5.11.1 Introduct
Page 127 and 128: Baud Rate 5.12.2.2 Topic configurat
Page 129 and 130: Examples • Bit access modifier: G
Page 131 and 132: 5.13 S7-200 (PPI - ISOTCP) 5.13.1 I
Page 133 and 134: 5.13.2.4 Topic configuration Genera
Page 135 and 136: • Status register: General Refere
Page 137 and 138: 5.14.1.1.2 Topic configuration Gene
Page 139 and 140: Note: The Modifier can by omitted,
Page 141 and 142: 5.15 MITSUBISHI FX IO Server 5.15.1
Page 143 and 144: 5.15.3.1 Value Name The syntax is t
Page 145 and 146: 5.16 SNMP IO Server 5.16.1 Introduc
Page 147 and 148:
• Status register: General Refere
Page 149 and 150:
6.1 Real-time screen General Refere
Page 151 and 152:
General Reference Guide Monitoring
Page 153 and 154:
6.4 Real time Alarm screen Figure 1
Page 155 and 156:
6.6 Files transfer This link gives
Page 157 and 158:
General Reference Guide Monitoring
Page 159 and 160:
6.7.2.1 Memory Information 6.7.2.2
Page 161 and 162:
6.7.2.5 Info 6.7.3 Scheduled Action
Page 163 and 164:
6.7.4.2 Activate Energy debug mode
Page 165 and 166:
7 Retrieving Data from eWON 7.1 Lis
Page 167 and 168:
7.3 FTP transfer FTP stands for the
Page 169 and 170:
8.2 Export fields syntax definition
Page 171 and 172:
8.2.4 $ut [Update Time] General Ref
Page 173 and 174:
$ft General Reference Guide Export
Page 175 and 176:
For fixed interval, $in parameter m
Page 177 and 178:
8.3.4 $dtAH [Alarm History] General
Page 179 and 180:
8.3.6 $dtEV [EVent file] 8.3.6.1 Ex
Page 181 and 182:
8.3.8 $dtSE [Script Expression] 8.3
Page 183 and 184:
General Reference Guide Export Bloc
Page 185 and 186:
General Reference Guide Export Bloc
Page 187 and 188:
8.3.11 $dtSV General Reference Guid
Page 189 and 190:
8.3.14 $dtSC General Reference Guid
Page 191 and 192:
8.3.16 $dtTR [TAR file] 8.3.16.1 Ex
Page 193 and 194:
9 Upgrading the eWON firmware 9.1 P
Page 195 and 196:
Click on the Finish Button when the
Page 197 and 198:
General Reference Guide Upgrading t
Page 199 and 200:
9.5 Upgrade Bootloader (to upgrade
Page 201 and 202:
10.2.2 Non-volatile configuration T
Page 203 and 204:
If an error is detected during the
Page 205 and 206:
10.7 Duplicate IP detection (User L
show all

eWON Family - eWON Support

Create successful ePaper yourself

Delete template?

Save as template?