Preliminary C8051F120/1/2/3 C8051F124/5/6/7 - KEMT FEI TUKE

More documents

Recommendations

Info

C8051F120/1/2/3 C8051F124/5/6/7 Preliminary The Temperature Sensor transfer function is shown in Figure 5.2. The output voltage (V TEMP ) is the PGA input when the Temperature Sensor is selected by bits AMX0AD3-0 in register AMX0SL; this voltage will be amplified by the PGA according to the user-programmed PGA settings. Figure 5.2. Typical Temperature Sensor Transfer Function (Volts) 1.000 0.900 0.800 0.700 V TEMP = 0.00286(TEMP C ) + 0.776 for PGA Gain = 1 0.600 0.500 -50 0 50 100 (Celsius) Page 48 DS008-0.8-AUG02 © 2002 Cygnal Integrated Products, Inc.
Preliminary C8051F120/1/2/3 C8051F124/5/6/7 5.2. ADC Modes of Operation ADC0 has a maximum conversion speed of 100 ksps. The ADC0 conversion clock is derived from the system clock divided by the value held in the ADCSC bits of register ADC0CF. 5.2.1. Starting a Conversion A conversion can be initiated in one of four ways, depending on the programmed states of the ADC0 Start of Conversion Mode bits (AD0CM1, AD0CM0) in ADC0CN. Conversions may be initiated by: 1. Writing a ‘1’ to the AD0BUSY bit of ADC0CN; 2. A Timer 3 overflow (i.e. timed continuous conversions); 3. A rising edge detected on the external ADC convert start signal, CNVSTR0; 4. A Timer 2 overflow (i.e. timed continuous conversions). The AD0BUSY bit is set to logic 1 during conversion and restored to logic 0 when conversion is complete. The falling edge of AD0BUSY triggers an interrupt (when enabled) and sets the AD0INT interrupt flag (ADC0CN.5). Converted data is available in the ADC0 data word MSB and LSB registers, ADC0H, ADC0L. Converted data can be either left or right justified in the ADC0H:ADC0L register pair (see example in Figure 5.11) depending on the programmed state of the AD0LJST bit in the ADC0CN register. When initiating conversions by writing a ‘1’ to AD0BUSY, the AD0INT bit should be polled to determine when a conversion has completed (ADC0 interrupts may also be used). The recommended polling procedure is shown below. Step 1. Write a ‘0’ to AD0INT; Step 2. Write a ‘1’ to AD0BUSY; Step 3. Poll AD0INT for ‘1’; Step 4. Process ADC0 data. When CNVSTR0 is used as a conversion start source, it must be enabled in the crossbar, and the corresponding pin must be set to open-drain, high-impedance mode (see Section “18. PORT INPUT/OUTPUT” on page 203 for more details on Port I/O configuration). © 2002 Cygnal Integrated Products, Inc. DS008-0.8-AUG02 Page 49
Page 1 and 2: Preliminary C8051F120/1/2/3 C8051F1
Page 43 and 44: © 2002 Cygnal Integrated Products,
Page 45 and 46: © 2002 Cygnal Integrated Products,
Page 47: Preliminary C8051F120/1/2/3 C8051F1
Page 99 and 100:
Preliminary C8051F120/1/2/3 C8051F1
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
show all

Preliminary C8051F120/1/2/3 C8051F124/5/6/7 - KEMT FEI TUKE

Create successful ePaper yourself

Delete template?

Save as template?