Condair Dual 2 manual.pdf

More documents

Recommendations

Info

4.2.1 Installation of the nozzle system A B C D E F 16 Flow direction The components of the nozzle system are supplied separately and must be assembled at the installation site. The following sections explain the general installation of the nozzle system. Detailed information (dimensions, fastening points, etc.) can be found in the “installation drawing” supplied with your particular system. Important! The dimensions listed in the installation drawing are mandatory. The nozzle system comprises the following main components: A Two fixing straps for fixing the vertical mounting rails to the duct wall B Two or more horizontal mounting rails C Two vertical mounting rails, which are fixed to the duct wall with the fixing straps D A number of connection plates for fixing the horizontal mounting rails to the vertical mounting rails E One or more nozzle grids with inserted nozzles F Four or six grid bearings per nozzle grid G Two or three housing entries G
First fix the two vertical mounting rails on both sides in the duct (see installation drawing for positioning and fixing). Important! Use exclusively the fixing materials provided. If this is not possible in your case, make absolutely sure that the fixing holes are correctly sealed from the inside of the duct with suitable components. 1 2 3 4 ø3.3 mm 1. Mark the positions of the holes for the fixing straps on the duct wall and drill the ø3.3 mm holes. Important! Make sure that the fixing holes in the left and right duct wall are exactly aligned opposite each other and that the axes of the upper and lower fixing holes are at right angles to the ceiling of the duct. Then, fix the vertical mounting rails to the wall of the duct with the fixing straps and screws provided. 2. Fix the connector plates to the vertical mounting rails using the screws and sliding nuts provided. 3. Fix the horizontal mounting rails to the connector plates using the screws and sliding nuts provided. ø3.3 mm ø3.3 mm 4. In ducts being wider than 2m: – connect all the adjacently positioned horizontal mounting rails (at the centre, if possible) using the profiled screwed connector/s provided. – mount the vertical strut/s between the horizontal mounting rails at the specified position. – mount the supplied ceiling attachment and bottom support to the duct ceiling and the duct bottom using the self-tapping screws provided (first drill the ø3.3 mm holes). 17
Page 1: 1120506 EN 0505 Hybrid Humidifier C
Page 4 and 5: 1 Introduction 1.1 To the very begi
Page 6 and 7: 2 Important notes 2.1 Correct use f
Page 8 and 9: 3 Overview of the Condair Dual Hybr
Page 10 and 11: 10 2 ... 10 bar Y8 Y7 Y6 Y5 Spray c
Page 12 and 13: 1 Humidification unit 2a Control un
Page 14 and 15: 4 Installation and first-time commi
Page 18 and 19: 5 8 18 Y6 (red) Y7 (blue) Y8 (yello
Page 20 and 21: 20 First attach the upper cross arm
Page 22 and 23: 22 7 7. Fix each vertical section,
Page 24 and 25: 24 Mounting and alignment of the ve
Page 26 and 27: 26 V 13 13. Mounting the brackets f
Page 28 and 29: 28 16 65 mm 16. From the back, hang
Page 30 and 31: 30 20 20. Insert in the lower flow
Page 32 and 33: 32 Install the upper flow sheets: 2
Page 34 and 35: 34 Install the tub seal: 27 27. Cut
Page 36 and 37: 4.4 Installation of the components
Page 38 and 39: 4.5 Water installation 1 Shut-off v
Page 40 and 41: 40 Notes on water installation - Th
Page 42 and 43: 4.6 Electrical installation F2 Q Ag
Page 44 and 45: 4.7 First-time commissioning 44 The
Page 46 and 47: 46 error XX XXXXXXXXXXXXXXXX Condai
Page 48 and 49: 5.4 Inquiring operating parameters
Page 50 and 51: 50 perform. [kg/h] appliance: 100 p
Page 52 and 53: 5.5 Setting up operating parameters
Page 54 and 55: 54 E Condair Dual ready and entry c
Page 56 and 57: 56 P-band 10 % integr.time 15 Min -
Page 58 and 59: Item Work to be carried out Nozzle
Page 60 and 61: 6.3 Removal and installation of com
Page 62 and 63: 6.3.2 Removal and installation of t
Page 64 and 65: 6.5 Replacement of the control unit
Page 66 and 67:
Alarm message Cause/Remedy 66 alarm
Page 68 and 69:
7.2 Failures Residual water in the
Page 70 and 71:
8 Specifications/ambient conditions
Page 72 and 73:
72 h,x diagram ∆ ∆ ∞ ∞
Page 74 and 75:
Incoming air 74 Circulating air Mix
Page 76 and 77:
Condair Dual 2 Commissioning protoc
Page 78 and 79:
9.4 Setup table silver ionization
Page 80:
Reg.No. 40002-2 Manufacturer: Axair
show all

Condair Dual 2 manual.pdf

Create successful ePaper yourself

Delete template?

Save as template?