Condair Dual 2 manual.pdf

More documents

Recommendations

Info

26 V 13 13. Mounting the brackets for the upper flow sheets: Starting with the narrow vertical section (left or right), align the front edge of the first bracket with the front edge of the topmost opening in the vertical section (see figure above), then fix the bracket to the duct roof using 2 (or 3, as required) self-tapping screws (drill holes ø3.3 mm before). Mount the remaining brackets in an offset order (front/rear, see figure above). Important! Mount the bracket marked with a “V” between the vertical sections with system-specific width. 14 V ø3.3 mm ø3.3 mm ø3.3 mm 14. Fix self-adhesive sealing plates to the two remaining angle brackets (see illustration above). Use the M6x12 hexagon socket screws provided to fix the angle brackets to the lower end of the two middle vertical sections. Push angle brackets down to the duct floor, then fasten M6x12 hexagon socket screws. Now fix the angle brackets to the duct floor using two self-tapping screws provided (drill holes ø3.3 mm before). Important! Depending on the slope of the tub the angle brackets may need to be fixed to the vertical sections using the extensions provided (see enlarged section in the figure above).
Install the booster elements (only on systems with “Booster”) If your system is equipped with a “Booster”, the booster elements must now be mounted. Note: If the post-evaporation unit is accessible from the back via a service door the “Booster” may be installed at the end of the installation procedure. The connector pieces and the short snap lashes are then mounted from the back. Mounting the booster at the end facilitates the installation of the ceramic plates and the ceramic angles. 15 15. First fix the two upper brackets to all booster elements using the thread plates and the M6x12 mm hexagon socket screws (use topmost oblong holes). Important! Tighten the screws by hand only to a point at which the brackets can still be moved. 27
Page 1: 1120506 EN 0505 Hybrid Humidifier C
Page 4 and 5: 1 Introduction 1.1 To the very begi
Page 6 and 7: 2 Important notes 2.1 Correct use f
Page 8 and 9: 3 Overview of the Condair Dual Hybr
Page 10 and 11: 10 2 ... 10 bar Y8 Y7 Y6 Y5 Spray c
Page 12 and 13: 1 Humidification unit 2a Control un
Page 14 and 15: 4 Installation and first-time commi
Page 16 and 17: 4.2.1 Installation of the nozzle sy
Page 18 and 19: 5 8 18 Y6 (red) Y7 (blue) Y8 (yello
Page 20 and 21: 20 First attach the upper cross arm
Page 22 and 23: 22 7 7. Fix each vertical section,
Page 24 and 25: 24 Mounting and alignment of the ve
Page 28 and 29: 28 16 65 mm 16. From the back, hang
Page 30 and 31: 30 20 20. Insert in the lower flow
Page 32 and 33: 32 Install the upper flow sheets: 2
Page 34 and 35: 34 Install the tub seal: 27 27. Cut
Page 36 and 37: 4.4 Installation of the components
Page 38 and 39: 4.5 Water installation 1 Shut-off v
Page 40 and 41: 40 Notes on water installation - Th
Page 42 and 43: 4.6 Electrical installation F2 Q Ag
Page 44 and 45: 4.7 First-time commissioning 44 The
Page 46 and 47: 46 error XX XXXXXXXXXXXXXXXX Condai
Page 48 and 49: 5.4 Inquiring operating parameters
Page 50 and 51: 50 perform. [kg/h] appliance: 100 p
Page 52 and 53: 5.5 Setting up operating parameters
Page 54 and 55: 54 E Condair Dual ready and entry c
Page 56 and 57: 56 P-band 10 % integr.time 15 Min -
Page 58 and 59: Item Work to be carried out Nozzle
Page 60 and 61: 6.3 Removal and installation of com
Page 62 and 63: 6.3.2 Removal and installation of t
Page 64 and 65: 6.5 Replacement of the control unit
Page 66 and 67: Alarm message Cause/Remedy 66 alarm
Page 68 and 69: 7.2 Failures Residual water in the
Page 70 and 71: 8 Specifications/ambient conditions
Page 72 and 73: 72 h,x diagram ∆ ∆ ∞ ∞
Page 74 and 75: Incoming air 74 Circulating air Mix
Page 76 and 77:
Condair Dual 2 Commissioning protoc
Page 78 and 79:
9.4 Setup table silver ionization
Page 80:
Reg.No. 40002-2 Manufacturer: Axair
show all

Condair Dual 2 manual.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?