R_Bibb_Medical_Modelling_The_Application_of_Adv.pdf

More documents

Recommendations

Info

Case studies 153 surface on which the fl at saw blade rests. As the cut is in two places on either side of the maxilla, the software design tools are used to join the two parts together into one device, see Figs 6.29 and 6.30. However, it was discovered that at this time there was no way to simulate the bending of the distractor attachment plates using the software. Whilst it was theoretically possible to design and manufacture custom fi tting plates and laser weld 6.29 Patient data and surgical guide design. 6.30 Finished surgical guide design.
154 Medical modelling 6.31 The surgical guide and supports. 6.32 The fi nished surgical guide. them to the distraction devices, the manufacturer of the devices would not allow the modifi cations. The guide was ‘therefore’ fi nalised, supported and built as described above. The support structure can be seen in Fig. 6.31. The drilling positions for the distraction devices were planned on an SL model of the patient. The SLM TM surgical guide was then fi tted to the model and the drilling sites transferred to it. The fi nal guide is shown in Fig. 6.32. 6.6.5 Results The surgical guides made to date were all assessed by the clinicians before going to surgery and all were deemed satisfactory for surgical use. All of the guides used in theatre so far have displayed good accuracy and fi tted the patients’ anatomy fi rmly and securely, as expected. The quality of the surgical guide fi t for this particular case was assessed by an experienced maxillofacial prosthetist. This was achieved by fi tting it to a SL model of the patient’s facial skeletal anatomy where it was found to show excellent fi t. Figure 6.33 shows the guide in situ in theatre.
Page 2 and 3:
Medical modelling
Page 4 and 5:
Medical modelling The application o
Page 6 and 7:
Contents Preface ix Acknowledgement
Page 8:
Contents vii 6.10 Rehabilitation ap
Page 11 and 12:
x Preface Therefore, it is hoped th
Page 14 and 15:
1.1 Background 1 Introduction The p
Page 16 and 17:
Introduction 3 Whilst this book is
Page 18 and 19:
Long axis 1.1 The anatomical positi
Page 20 and 21:
Introduction 7 1.3 The major refere
Page 22 and 23:
Medical imaging for rapid prototypi
Page 24 and 25:
Page 26 and 27:
2.2.3 Anatomical coverage Medical i
Page 28 and 29:
Page 30 and 31:
2.6 X-ray scatter artefact in a CT
Page 32 and 33:
2.9 Close up of noise. Medical imag
Page 34 and 35:
2.12 Smooth data. Medical imaging f
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
1 Medical imaging for rapid prototy
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Export data format and media 33 (NE
Page 48 and 49:
3.3 Media Export data format and me
Page 50 and 51:
4.1 Pixel data operations 4 Working
Page 52 and 53:
4.3 Effect of a high threshold. 4.4
Page 54 and 55:
Working with medical scan data 41 4
Page 56 and 57:
Page 58 and 59:
Working with medical scan data 45 S
Page 60 and 61:
4.4 Two-dimensional formats Working
Page 62 and 63:
Page 64 and 65:
Working with medical scan data 51 I
Page 66 and 67:
4.18 Close up view showing facets.
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
5.1 Background to rapid prototyping
Page 74 and 75:
Physical reproduction 61 developing
Page 76 and 77:
Physical reproduction 63 will displ
Page 78 and 79:
Physical reproduction 65 As there i
Page 80 and 81:
Physical reproduction 67 However, t
Page 82 and 83:
Data quality Physical reproduction
Page 84 and 85:
Physical reproduction 71 In some ca
Page 86 and 87:
Physical reproduction 73 Overhangin
Page 88 and 89:
Physical reproduction 75 5.10 SL mo
Page 90 and 91:
Physical reproduction 77 5.12 Selec
Page 92 and 93:
5.13 A Perfactory ® model of a man
Page 94 and 95:
5.15 FDM TM model of the mandible.
Page 96 and 97:
Table 5.3 Advantages and disadvanta
Page 98 and 99:
Physical reproduction 85 In medical
Page 100 and 101:
Table 5.5 Advantages and disadvanta
Page 102 and 103:
5.7 Jetting head technology 5.7.1 P
Page 104 and 105:
5.23 ThermoJet ® model of the mand
Page 106 and 107:
5.24 LOM TM model of the mandible.
Page 108 and 109:
5.26 LOM TM model of a partial face
Page 110 and 111:
6 Case studies The following case s
Page 112 and 113:
IMPLEMENTATION 6.1 Implementation c
Page 114 and 115:
Post model Hospital department Pati
Page 116 and 117: Case studies 103 When using this so
Page 118 and 119: Case studies 105 (Mimics). Image ma
Page 120 and 121: Case studies 107 full co-operation
Page 122 and 123: Case studies 109 communication and
Page 124 and 125: • to achieve patient’s agreemen
Page 126 and 127: 6.2.4 Rapid prototyping technologie
Page 128 and 129: Case studies 115 not be suitable. A
Page 130 and 131: Case studies 117 scale of the data
Page 132 and 133: 6.7 SL model with signifi cant stai
Page 134 and 135: Case studies 121 6.9a Smooth surfac
Page 136 and 137: Case studies 123 slice editing of t
Page 138 and 139: Case studies 125 6.12 Removal of bo
Page 140 and 141: Case studies 127 18. Williams R J,
Page 142 and 143: Case studies 129 and passing throug
Page 144 and 145: Case studies 131 6.14 The effect of
Page 146 and 147: Case studies 133 6.18 The block ove
Page 148 and 149: Case studies 135 create template (3
Page 150 and 151: 6.4.3 Materials and methods Case st
Page 152 and 153: 6.22 Resected bone compared to SLA
Page 154 and 155: Case studies 141 9. Robinson R P, C
Page 156 and 157: Case studies 143 multi-plane reform
Page 158 and 159: Case studies 145 6.25 The custom ti
Page 160 and 161: Case studies 147 6.28 Plain radiogr
Page 162 and 163: Case studies 149 reproduction of ex
Page 164 and 165: Case studies 151 manner. The softwa
Page 168 and 169: 6.33 The guide being fi tted to the
Page 170 and 171: Case studies 157 The more fundament
Page 172 and 173: Case studies 159 25. Sarment D P, A
Page 174 and 175: 6.37 Stereolithography models. 6.38
Page 176 and 177: Case studies 163 6.41 Merged pre- a
Page 178 and 179: REHABILITATION APPLICATIONS 6.8 Reh
Page 180 and 181: 6.8.3 Methods Preliminary trial of
Page 182 and 183: Case studies 169 prototyping system
Page 184 and 185: Case studies 171 The aperture for t
Page 186 and 187: Case studies 173 7. Manners C R (19
Page 188 and 189: Case studies 175 during the acquisi
Page 190 and 191: 6.46 Smoothing the data (exaggerate
Page 192 and 193: 6.49 Plaster fi lled SL mould. Case
Page 194 and 195: Case studies 181 diffi cult for hos
Page 196 and 197: Case studies 183 extremely diffi cu
Page 198 and 199: Case studies 185 back as shown in F
Page 200 and 201: 6.54 The result of the Boolean subt
Page 202 and 203: 6.56 The SLA model of the plate. Ca
Page 204 and 205: 6.59 SLA implant on SLA model of de
Page 206 and 207: Case studies 193 In the near future
Page 208 and 209: Case studies 195 anatomical forms a
Page 210 and 211: Case studies 197 Establishing the c
Page 212 and 213: Case studies 199 6.63 The rough (a)
Page 214 and 215: Case studies 201 The fi nal prosthe
Page 216 and 217:
Case studies 203 grating the techno
Page 218 and 219:
Case studies 205 6.12 Rehabilitatio
Page 220 and 221:
Case studies 207 • Data capture N
Page 222 and 223:
Case studies 209 placement of two i
Page 224 and 225:
Case studies 211 technique that has
Page 226 and 227:
Case studies 213 6.72 The bar locat
Page 228 and 229:
Case studies 215 Stereolithography
Page 230 and 231:
Case studies 217 authors intend to
Page 232 and 233:
Case studies 219 17. Kau C H, Zhuro
Page 234 and 235:
Case studies 221 310, Sainte-Foy, Q
Page 236 and 237:
6.77a The physically surveyed cast.
Page 238 and 239:
Creation of relief Case studies 225
Page 240 and 241:
6.81 Construction curves. Case stud
Page 242 and 243:
6.83 The support structure in 3D Li
Page 244 and 245:
Finishing Case studies 231 The cast
Page 246 and 247:
Case studies 233 6.14 Rehabilitatio
Page 248 and 249:
6.86 The RPD framework designed in
Page 250 and 251:
Second experiment Case studies 237
Page 252 and 253:
Case studies 239 6.90 Close up view
Page 254 and 255:
Table 6.2 Process steps and associa
Page 256 and 257:
Case studies 243 9. Budtz-Jorgensen
Page 258 and 259:
Case studies 245 micro-computed tom
Page 260 and 261:
Case studies 247 supports became av
Page 262 and 263:
Case studies 249 However, the probl
Page 264 and 265:
6.96 Model of one of the samples su
Page 266 and 267:
6.15.9 Reference Case studies 253 1
Page 268 and 269:
Case studies 255 mummies. Mimics so
Page 270 and 271:
Case studies 257 6.101 3D reconstru
Page 272 and 273:
Case studies 259 6.103 The stages o
Page 274 and 275:
6.16.5 Conclusions Case studies 261
Page 276 and 277:
Case studies 263 the patient’s de
Page 278 and 279:
Case studies 265 and sharp radii re
Page 280 and 281:
Suitable technologies identifi ed C
Page 282 and 283:
Case studies 269 6.107 A close-up p
Page 284 and 285:
6.110 The selected region of facial
Page 286 and 287:
Case studies 273 patterns were buil
Page 288 and 289:
Case studies 275 7. Cheah C M, Chua
Page 290 and 291:
Future developments 277 slices to b
Page 292 and 293:
Future developments 279 ments that
Page 294 and 295:
Glossary and explanatory notes 281
Page 296 and 297:
Glossary and explanatory notes 283
Page 298 and 299:
Further reading on anatomy Last’s
Page 300 and 301:
Fundamentals of Facial Prosthetics
Page 302 and 303:
Rapid Prototyping and Tooling Resea
Page 304 and 305:
Contacts 3D Systems 26081 Avenue Ha
Page 306 and 307:
Marcam Engineering GmbH Fahrenheits
Page 308 and 309:
3D Lightyear TM 229, 247, 249-51, 2
Page 310:
Removable Partial Denture 219-20, 2
Page 313 and 314:
4.10 A three-dimensional shaded ima
Page 315:
6.41 Merged pre- and post-operative
show all

R_Bibb_Medical_Modelling_The_Application_of_Adv.pdf

Create successful ePaper yourself

Delete template?

Save as template?