R_Bibb_Medical_Modelling_The_Application_of_Adv.pdf

More documents

Recommendations

Info

Working with medical scan data 49 4.14 Segmented region showing smooth polyline boundaries. 4.15 2 1 / 2D polyline data (right) compared to 3D rendered model (left). The middle images show how they relate to each other.
50 Medical modelling be generated with suffi cient resolution such that curved surfaces on RP models derived from them appear smooth. The format was developed by 3D Systems as an alternative input fi le for their stereolithography technology. If an SLC fi le can be generated from the original source data, it effectively bypasses the need to create STL fi les. For a given data set, an SLC fi le will be much smaller than an STL fi le of comparable resolution. For example, for the data illustrated in Fig. 4.9 the SLC fi le would be 28.0 MB, which would compare favourably with the equivalent quality STL fi le which would be 94.3 MB. Therefore, the SLC provides a highly effi cient data transfer format for medical modelling using stereolithography. 4.5.3 CLI Common Layer Interface is a contour fi le format that describes crosssectional slices through an object in much the same way as the SLC fi le. However, the format is commonly available to many software developers and may be used with a variety of RP technologies. For comparison, the CLI fi le of the data illustrated in Fig. 4.9 would be 13.8 MB. 4.5.4 SLI Also derived from the word ‘slice’, the SLI fi le format is similar to the SLC fi le format but, rather than being an input fi le, it is an intermediate fi le format created during the preparation of stereolithography builds. The fi le, developed by 3D Systems, not only describes the perimeter of the slices but also includes raster lines that make up the cross-sectional area within the boundary. These raster scan lines are usually referred to as hatches. The fi le format also includes different types of hatch for up-facing and downfacing layers. This is important in stereolithography because up-facing and down-facing layers are built differently to optimise accuracy. As with the SLC fi le format, the ability to generate this fi le format directly from medical scan data provides an effi cient data transfer when generating stereolithography fi les. The extra hatch information contained in the fi le increases its size in comparison to the SLC. For example, the SLI fi le of the data illustrated in Fig. 4.9 would be 46.1 MB. 4.6 True three-dimensional formats 4.6.1 Polygon faceted surfaces Unlike the contour or slice-based formats described above, true threedimensional data formats generate computer models that have a surface.
Page 2 and 3:
Medical modelling
Page 4 and 5:
Medical modelling The application o
Page 6 and 7:
Contents Preface ix Acknowledgement
Page 8:
Contents vii 6.10 Rehabilitation ap
Page 11 and 12: x Preface Therefore, it is hoped th
Page 14 and 15: 1.1 Background 1 Introduction The p
Page 16 and 17: Introduction 3 Whilst this book is
Page 18 and 19: Long axis 1.1 The anatomical positi
Page 20 and 21: Introduction 7 1.3 The major refere
Page 22 and 23: Medical imaging for rapid prototypi
Page 26 and 27: 2.2.3 Anatomical coverage Medical i
Page 30 and 31: 2.6 X-ray scatter artefact in a CT
Page 32 and 33: 2.9 Close up of noise. Medical imag
Page 34 and 35: 2.12 Smooth data. Medical imaging f
Page 40 and 41: 1 Medical imaging for rapid prototy
Page 46 and 47: Export data format and media 33 (NE
Page 48 and 49: 3.3 Media Export data format and me
Page 50 and 51: 4.1 Pixel data operations 4 Working
Page 52 and 53: 4.3 Effect of a high threshold. 4.4
Page 54 and 55: Working with medical scan data 41 4
Page 58 and 59: Working with medical scan data 45 S
Page 60 and 61: 4.4 Two-dimensional formats Working
Page 64 and 65: Working with medical scan data 51 I
Page 66 and 67: 4.18 Close up view showing facets.
Page 72 and 73: 5.1 Background to rapid prototyping
Page 74 and 75: Physical reproduction 61 developing
Page 76 and 77: Physical reproduction 63 will displ
Page 78 and 79: Physical reproduction 65 As there i
Page 80 and 81: Physical reproduction 67 However, t
Page 82 and 83: Data quality Physical reproduction
Page 84 and 85: Physical reproduction 71 In some ca
Page 86 and 87: Physical reproduction 73 Overhangin
Page 88 and 89: Physical reproduction 75 5.10 SL mo
Page 90 and 91: Physical reproduction 77 5.12 Selec
Page 92 and 93: 5.13 A Perfactory ® model of a man
Page 94 and 95: 5.15 FDM TM model of the mandible.
Page 96 and 97: Table 5.3 Advantages and disadvanta
Page 98 and 99: Physical reproduction 85 In medical
Page 100 and 101: Table 5.5 Advantages and disadvanta
Page 102 and 103: 5.7 Jetting head technology 5.7.1 P
Page 104 and 105: 5.23 ThermoJet ® model of the mand
Page 106 and 107: 5.24 LOM TM model of the mandible.
Page 108 and 109: 5.26 LOM TM model of a partial face
Page 110 and 111: 6 Case studies The following case s
Page 112 and 113:
IMPLEMENTATION 6.1 Implementation c
Page 114 and 115:
Post model Hospital department Pati
Page 116 and 117:
Case studies 103 When using this so
Page 118 and 119:
Case studies 105 (Mimics). Image ma
Page 120 and 121:
Case studies 107 full co-operation
Page 122 and 123:
Case studies 109 communication and
Page 124 and 125:
• to achieve patient’s agreemen
Page 126 and 127:
6.2.4 Rapid prototyping technologie
Page 128 and 129:
Case studies 115 not be suitable. A
Page 130 and 131:
Case studies 117 scale of the data
Page 132 and 133:
6.7 SL model with signifi cant stai
Page 134 and 135:
Case studies 121 6.9a Smooth surfac
Page 136 and 137:
Case studies 123 slice editing of t
Page 138 and 139:
Case studies 125 6.12 Removal of bo
Page 140 and 141:
Case studies 127 18. Williams R J,
Page 142 and 143:
Case studies 129 and passing throug
Page 144 and 145:
Case studies 131 6.14 The effect of
Page 146 and 147:
Case studies 133 6.18 The block ove
Page 148 and 149:
Case studies 135 create template (3
Page 150 and 151:
6.4.3 Materials and methods Case st
Page 152 and 153:
6.22 Resected bone compared to SLA
Page 154 and 155:
Case studies 141 9. Robinson R P, C
Page 156 and 157:
Case studies 143 multi-plane reform
Page 158 and 159:
Case studies 145 6.25 The custom ti
Page 160 and 161:
Case studies 147 6.28 Plain radiogr
Page 162 and 163:
Case studies 149 reproduction of ex
Page 164 and 165:
Case studies 151 manner. The softwa
Page 166 and 167:
Case studies 153 surface on which t
Page 168 and 169:
6.33 The guide being fi tted to the
Page 170 and 171:
Case studies 157 The more fundament
Page 172 and 173:
Case studies 159 25. Sarment D P, A
Page 174 and 175:
6.37 Stereolithography models. 6.38
Page 176 and 177:
Case studies 163 6.41 Merged pre- a
Page 178 and 179:
REHABILITATION APPLICATIONS 6.8 Reh
Page 180 and 181:
6.8.3 Methods Preliminary trial of
Page 182 and 183:
Case studies 169 prototyping system
Page 184 and 185:
Case studies 171 The aperture for t
Page 186 and 187:
Case studies 173 7. Manners C R (19
Page 188 and 189:
Case studies 175 during the acquisi
Page 190 and 191:
6.46 Smoothing the data (exaggerate
Page 192 and 193:
6.49 Plaster fi lled SL mould. Case
Page 194 and 195:
Case studies 181 diffi cult for hos
Page 196 and 197:
Case studies 183 extremely diffi cu
Page 198 and 199:
Case studies 185 back as shown in F
Page 200 and 201:
6.54 The result of the Boolean subt
Page 202 and 203:
6.56 The SLA model of the plate. Ca
Page 204 and 205:
6.59 SLA implant on SLA model of de
Page 206 and 207:
Case studies 193 In the near future
Page 208 and 209:
Case studies 195 anatomical forms a
Page 210 and 211:
Case studies 197 Establishing the c
Page 212 and 213:
Case studies 199 6.63 The rough (a)
Page 214 and 215:
Case studies 201 The fi nal prosthe
Page 216 and 217:
Case studies 203 grating the techno
Page 218 and 219:
Case studies 205 6.12 Rehabilitatio
Page 220 and 221:
Case studies 207 • Data capture N
Page 222 and 223:
Case studies 209 placement of two i
Page 224 and 225:
Case studies 211 technique that has
Page 226 and 227:
Case studies 213 6.72 The bar locat
Page 228 and 229:
Case studies 215 Stereolithography
Page 230 and 231:
Case studies 217 authors intend to
Page 232 and 233:
Case studies 219 17. Kau C H, Zhuro
Page 234 and 235:
Case studies 221 310, Sainte-Foy, Q
Page 236 and 237:
6.77a The physically surveyed cast.
Page 238 and 239:
Creation of relief Case studies 225
Page 240 and 241:
6.81 Construction curves. Case stud
Page 242 and 243:
6.83 The support structure in 3D Li
Page 244 and 245:
Finishing Case studies 231 The cast
Page 246 and 247:
Case studies 233 6.14 Rehabilitatio
Page 248 and 249:
6.86 The RPD framework designed in
Page 250 and 251:
Second experiment Case studies 237
Page 252 and 253:
Case studies 239 6.90 Close up view
Page 254 and 255:
Table 6.2 Process steps and associa
Page 256 and 257:
Case studies 243 9. Budtz-Jorgensen
Page 258 and 259:
Case studies 245 micro-computed tom
Page 260 and 261:
Case studies 247 supports became av
Page 262 and 263:
Case studies 249 However, the probl
Page 264 and 265:
6.96 Model of one of the samples su
Page 266 and 267:
6.15.9 Reference Case studies 253 1
Page 268 and 269:
Case studies 255 mummies. Mimics so
Page 270 and 271:
Case studies 257 6.101 3D reconstru
Page 272 and 273:
Case studies 259 6.103 The stages o
Page 274 and 275:
6.16.5 Conclusions Case studies 261
Page 276 and 277:
Case studies 263 the patient’s de
Page 278 and 279:
Case studies 265 and sharp radii re
Page 280 and 281:
Suitable technologies identifi ed C
Page 282 and 283:
Case studies 269 6.107 A close-up p
Page 284 and 285:
6.110 The selected region of facial
Page 286 and 287:
Case studies 273 patterns were buil
Page 288 and 289:
Case studies 275 7. Cheah C M, Chua
Page 290 and 291:
Future developments 277 slices to b
Page 292 and 293:
Future developments 279 ments that
Page 294 and 295:
Glossary and explanatory notes 281
Page 296 and 297:
Glossary and explanatory notes 283
Page 298 and 299:
Further reading on anatomy Last’s
Page 300 and 301:
Fundamentals of Facial Prosthetics
Page 302 and 303:
Rapid Prototyping and Tooling Resea
Page 304 and 305:
Contacts 3D Systems 26081 Avenue Ha
Page 306 and 307:
Marcam Engineering GmbH Fahrenheits
Page 308 and 309:
3D Lightyear TM 229, 247, 249-51, 2
Page 310:
Removable Partial Denture 219-20, 2
Page 313 and 314:
4.10 A three-dimensional shaded ima
Page 315:
6.41 Merged pre- and post-operative
show all

R_Bibb_Medical_Modelling_The_Application_of_Adv.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?