Automatic control function programming manual ladder language

Variable M function Definition Cancelled by Type of function
(Group 1 to 8) Pre Post Modal Non
modal
%Rg20.7 M999_1 M999_8 Programmed inhibit of MDI and
EDIT modes and subroutine calls by
the machine processor
M997, M998, M2 X X
%Rg20.6 M998_1* M998_8* Programmed enable of MDI and
EDIT modes and subroutine calls
by the machine processor
M999, M997 X X
%Rg20.5 M997_1 M997_8 Forced block continuation M998, M999, M2 X X
%Rg20.3 M49_1 M49_8 Feed rate and spindle potentiometers
forced to 100 percent
M48, M2 X X
%Rg20.2 M48_1* M48_8* Feed rate and spindle potentiometers
enabled
M49 X X
%Rg20.1 M11_1 M11_8 Axis unclamp M10 X X
%Rg20.0 M10_1 M10_8 Axis clamp M11 X X
%Rg21.7 M12_1 M12_8 Forcing of CYHLD mode C_CYCLE = 1 X X
%Rg21.5 M45_1 M45_8 Spindle ranges Cancelled by one X X
%Rg21.4 M44_1 M44_8 another or by M02 X X
%Rg21.3 M43_1 M43_8 X X
%Rg21.2 M42_1 M42_8 X X
%Rg21.1 M41_1 M41_8 X X
%Rg21.0 M40_1 M40_8 X X
%Rg22.7 M19_1 M19_8 Indexed spindle stop M0, M2, M3, M4, ARUS X X
%Rg22.6 M09_1* M09_8* Coolant stop M7, M8 X X
%Rg22.5 M08_1 M08_8 Coolant 1 M9, M2 X X
%Rg22.4 M07_1 M07_8 Coolant 2 M9, M2 X X
%Rg22.3 M06_1 M06_8 Tool change CRM1 to CRM8 X X
%Rg22.2 M05_1* M05_8* Spindle stop M3, M4 X X
%Rg22.1 M04_1 M04_8 Anticlockwise spindle rotation M3, M5, M19, M0, M2 X X
%Rg22.0 M03_1 M03_8 Clockwise spindle rotation M4, M5, M19, M0, M2 X X
%Rg23.7 M61_1 M61_8 Current spindle disabled in a group M64, M65, M62, M63 X X
%Rg23.2 M02_1 M02_8 End of part programme RAZ X X
%Rg23.1 M01_1 M01_8 Optional stop C_CYCLE key X
%Rg23.0 M00_1 M00_8 Programme stop C_CYCLE key X
(*) Function initialised at power on by a reset or by function M02.
3.8.3.7 Decoded M Functions (Spindle Status): %Rg24.W
Variable M function Definition Cancelled by Type of function
(Group 1 to 8) Pre Post Modal Non
modal
%Rg24.3 M63_1 M63_8 Spindle reference applied to
spindle 4. M61, M62, M64, M65 X X
%Rg24.2 M62_1 M62_8 Spindle reference applied to
spindle 3. M61, M63, M64, M65 X X
%Rg24.1 M65_1 M65_8 Spindle reference applied to
spindle 2. M61, M62, M63, M64 X X
%Rg24.0 M64_1 M64_8 Spindle reference applied to
spindle 1. M61, M62, M63, M65 X X
3 - 58 en-938846/8