Automatic control function programming manual ladder language

More documents

Recommendations

Info

3.7.4.4 Watchdog %Qrc3B.0 Must be programmed in the %INI task. When this bit is set, it indicates that output %Qrc00.0 of this card is a watchdog output. Two watchdogs are allowed. The monitor scans all of variables %Qrc3B.0 and selects the first two watchdogs programmed in increasing order (r,c). If the watchdog is not initialised, the general I/O card configuration error bit %R97F.1 (DEFCONF) is set, the inputs and outputs are no longer refreshed and the watchdog is reset. 3.7.4.5 NC Access Enable %Qrc3B.1 Enables or disables access to the output cards (by parameters E33xxx) and the input cards (by parameters E43xxx) by the part programmes. The variable equals 0 to inhibit access to the card by the part programme. The variable equals 1 to enable access to the card by the part programme. Variable %Qrc3B.1 is set to a default value of 0 by the monitor. REMARK %Qrc3B.1 must be programmed in %INI. Depending on the state of variable %W900.0, access to the outputs is enabled or inhibited by E33xxx. 3 - 14 en-938846/6
3.7.5 Physical Organisation of Variables %I and %Q Variables Variables %I and %Q are organised as memory blocks of 64 %I bytes followed by 64 %Q bytes corresponding to one card then to the next card until reaching the last card of the rack. The racks are consecutive and contiguous (from rack 0 to rack 6). 3.7.5.1 Physical Organisation of Variables %I and %Q of Rack r Offset 0 3F 7F BF FF 700 73F 77F 7BF 7FF %Ir00 to %Ir03F %Qr00 to %Qr03F %Ir100 to %Ir13F %Qr100 to %Qr13F %IrE00 to %IrE3F %QrE00 to %QrE3F %IrF00 to %IrF3F %QrF00 to %QrF3F 64 bytes %I card 0 64 bytes %Q card 0 64 bytes %I card 1 64 bytes %Q card 1 64 bytes %I card E 64 bytes %Q card E 64 bytes %I card F 64 bytes %Q card F en-938846/6 3 - 15 3
Page 1 and 2:
NUM AUTOMATIC CONTROL FUNCTION PROG
Page 3 and 4:
Table of Contents Table of Contents
Page 5 and 6:
Table of Contents 9 Analogue Inputs
Page 7 and 8: Record of Revisions Record of Revis
Page 9 and 10: Date Revision Reason for revisions
Page 11 and 12: Structure of the NUM 1020/1040/1060
Page 13 and 14: Automatic Control Function Programm
Page 15 and 16: CHAPTER 8 TRANSPARENT MODE CHAPTER
Page 17 and 18: CHAPTER 16 PROGRAMMING IN C LANGUAG
Page 19 and 20: Use of the Automatic Control Functi
Page 21 and 22: Presentation of the Automatic Contr
Page 23 and 24: 1.1 General Presentation of the Aut
Page 25 and 26: AXIS 1 INTERFACE AXIS 2 AXIS 3 AXIS
Page 27 and 28: µ p 68020 SYSTEM BUS BUS INTERFACE
Page 29 and 30: Structure of an Application 2 Struc
Page 31 and 32: 2.1 General The machine processor c
Page 33 and 34: 2.1.1.3 «System» I/O Card Refresh
Page 35 and 36: Operation of the Background Tasks N
Page 37 and 38: 2.1.2.4 Real-Time Tasks Structure o
Page 39 and 40: 2.1.3.2 1060 Series II- UCSII Syste
Page 41 and 42: 2.2 Structure of an Application Str
Page 43 and 44: 2.3 Structure of a Ladder Module -
Page 45 and 46: Variables 3 Variables 3.1 Principle
Page 47 and 48: Variables 3.8.2.19 Backward of Forw
Page 49 and 50: 3.1 Principle of Exchanges Variable
Page 51 and 52: Examples %M9 points to byte 9 of th
Page 53 and 54: 3.7 I/O Card Interface Variables %I
Page 55 and 56: 3.7.3.2 Card Status %Irc3C.W Variab
Page 57: A configuration change requires mov
Page 61 and 62: 3.7.6 Rack and Card Identifiers 3.7
Page 63 and 64: 3.7.8 Image Part of the 32 Discrete
Page 65 and 66: %Qrc00.0 to %Qrc02.7 %Irc00.0 to %I
Page 67 and 68: %Qrc03.0 to %Qrc05.7 2nd relay modu
Page 69 and 70: 3.7.12 Image Part of the Extension
Page 71 and 72: 3.7.13 Image Part of the Compact Pa
Page 73 and 74: 3.8 CNC I/O Interface Family %R and
Page 75 and 76: Variables Variable Mnemonic Descrip
Page 77 and 78: 3.8.1.7 Spindle Status: %R12.W Vari
Page 79 and 80: 3.8.1.10 Other Variables Variables
Page 81 and 82: 3.8.1.13 1050 Servo-Drive Status Wo
Page 83 and 84: Variable Mnemonic Description %W3.0
Page 85 and 86: 3.8.2.4 Negative JOG Commands: %WA.
Page 87 and 88: Programme %9999.9 must be structure
Page 89 and 90: 3.8.2.13 Spindle Controls: %W22.W V
Page 91 and 92: - Select spindle b control: COMBRb
Page 93 and 94: 3.8.2.16 Modes Inhibited: %W30.L Va
Page 95 and 96: 3.8.2.19 Backward of Forward Moveme
Page 97 and 98: 3.8.3 Inputs from the Axis Groups V
Page 99 and 100: 3.8.3.4 Encoded M Function Without
Page 101 and 102: Nonmodal functions A nonmodal funct
Page 103 and 104: Variables Variable M function Defin
Page 105 and 106: 3.8.4 Outputs to the Axis Groups Th
Page 107 and 108: 3.8.5 System Faults and Diagnostic
Page 109 and 110:
3.8.7 Output Card Write Enable: %W9
Page 111 and 112:
3.8.10 Physical Organisation of %R
Page 113 and 114:
3.9.3 Organisation of %S Common Wor
Page 115 and 116:
Language element Includes Comment V
Page 117 and 118:
B4_ARR B3_ARR B2_ARR B1_ARR B4_ROT
Page 119 and 120:
3.11.3 Output to the CNC CHG_ C_ C-
Page 121 and 122:
VER VER VER VER STOP STOP STOP STOP
Page 123 and 124:
3.11.4 PLC-CNC Exchange Area - 1050
Page 125 and 126:
M63 M62 M65 M64 %Rg24.7 %Rg24.6 %Rg
Page 127 and 128:
Literal Elements of Ladder Language
Page 129 and 130:
4.1 Notations Used The notations us
Page 131 and 132:
Literal Elements of Ladder Language
Page 133 and 134:
4.5.5 Order of Evaluation of the Ex
Page 135 and 136:
4.5.8 Overflow - Sign Change Litera
Page 137 and 138:
Programming in Ladder Language 5 Pr
Page 139 and 140:
5.1 Elements Common to All Types of
Page 141 and 142:
Programming in Ladder Language en-9
Page 143 and 144:
5.2 Network Sequence 5.2.1 General
Page 145 and 146:
Example 5.2.2.3 Conditional Actions
Page 147 and 148:
Off Timeout «TOF_n» E Q %TQxx.7 T
Page 149 and 150:
Upcounters E C Q %CQxx.7 Threshold
Page 151 and 152:
5.2.3 Structure of the Action Zone
Page 153 and 154:
Pitfall Related to Scanning Program
Page 155 and 156:
Invalid Network - Branch without Po
Page 157 and 158:
5.2.7 Programming Hints 5.2.7.1 Opt
Page 159 and 160:
Unoptimised Network Optimised Netwo
Page 161 and 162:
5.2.7.4 Testing the Bits of a Byte,
Page 163 and 164:
General Purpose Functions 6 General
Page 165 and 166:
General Purpose Functions 6.1 Conve
Page 167 and 168:
General Purpose Functions 6.3 BCD
Page 169 and 170:
General Purpose Functions 6.5 Separ
Page 171 and 172:
General Purpose Functions 6.7 Copy
Page 173 and 174:
Page 175 and 176:
Return code If OK Number of charact
Page 177 and 178:
General Purpose Functions 6.14 Simu
Page 179 and 180:
General Purpose Functions 6.17 Sear
Page 181 and 182:
General Purpose Functions 6.20 Jump
Page 183 and 184:
Return code If OK Not significant.
Page 185 and 186:
Return code If OK Value returned by
Page 187 and 188:
Return code If OK Number of charact
Page 189 and 190:
Page 191 and 192:
General Purpose Functions 6.34 Swap
Page 193 and 194:
General Purpose Functions 6.36 Read
Page 195 and 196:
General Purpose Functions 6.38 Init
Page 197 and 198:
Task Management 7 Task Management 7
Page 199 and 200:
7.1 Introduction Task Management Fo
Page 201 and 202:
Transparent Mode 8 Transparent Mode
Page 203 and 204:
8.1 Introduction Transparent Mode T
Page 205 and 206:
8.1.4 Character Codes Used by %R0.W
Page 207 and 208:
8.2 Functions Assigned to transpare
Page 209 and 210:
Transparent Mode Operation Sends a
Page 211 and 212:
Example 1 Consider the following va
Page 213 and 214:
Transparent Mode 8.2.7 Open a Numer
Page 215 and 216:
Return code Transparent Mode If OK
Page 217 and 218:
Transparent Mode Operation putimage
Page 219 and 220:
en-938846/7 8 - 19 Transparent Mode
Page 221 and 222:
471 470 89 76 40 0 4 16 COL. 0 A A
Page 223 and 224:
Transparent Mode Description Instru
Page 225 and 226:
8.3.4 Alphanumeric Characters and I
Page 227 and 228:
Format D (Expanded characters) 0x9B
Page 229 and 230:
Example To position the cursor on L
Page 231 and 232:
Definition of a Reference System Ce
Page 233 and 234:
J: «J» [VALUE] Current Y coordina
Page 235 and 236:
8.3.5.8 Shift Screen Origin Instruc
Page 237 and 238:
P2 P1 P1 P2 P1 P2 N1 P3 P1 N6 P0 P0
Page 239 and 240:
! CAUTION Arguments [CLIP], [X] and
Page 241 and 242:
Analogue Inputs/Outputs 9 Analogue
Page 243 and 244:
9.1 General Analogue Inputs/Outputs
Page 245 and 246:
Analogue Inputs/Outputs 9.3 Write a
Page 247 and 248:
Analogue Inputs/Outputs 9.5 Reassig
Page 249 and 250:
Explicit Read/Write of Input/Output
Page 251 and 252:
10.1 General Explicit Read/Write of
Page 253 and 254:
Explicit Read/Write of Input/Output
Page 255 and 256:
Interrupt Inputs 11 Interrupt Input
Page 257 and 258:
11.1 General The automatic control
Page 259 and 260:
11.2 Principle of Line Assignment N
Page 261 and 262:
Example Filtering on rising edge T1
Page 263 and 264:
Interrupt Inputs 11.6 Associate a %
Page 265 and 266:
Serial Lines 12 Serial Lines 12.1 G
Page 267 and 268:
12.1 General The automatic control
Page 269 and 270:
Detail of the «format» argument 0
Page 271 and 272:
PERIPHERAL Transmission to peripher
Page 273 and 274:
Copy requested No. into buffer Yes
Page 275 and 276:
Serial Lines 12.6 Control the Seria
Page 277 and 278:
Serial Lines 12.7.2.3 Xon/Xoff Flow
Page 279 and 280:
13.1 General Description of the Tim
Page 281 and 282:
14.1 General Description of the Dat
Page 283 and 284:
Exchanges by Protocol 15 Exchanges
Page 285 and 286:
15.1 General Description of Exchang
Page 287 and 288:
15.1.2 DNC1000 Exchange Mechanism E
Page 289 and 290:
15.2 Objects Accessible by a UNITE
Page 291 and 292:
15.2.2 Object Constituents The IU c
Page 293 and 294:
Exchanges by Protocol Segment Acces
Page 295 and 296:
Exchanges by Protocol Segment Acces
Page 297 and 298:
Detailed List of G Functions Presen
Page 299 and 300:
Example of reading the current prog
Page 301 and 302:
15.3.3 «DELETE-FILE» Request Used
Page 303 and 304:
Negative answer ANSWER CODE (1 byte
Page 305 and 306:
Request format Answer format Positi
Page 307 and 308:
15.3.8 «READ-BLOCK» Request Used
Page 309 and 310:
15.3.10 «RESERVE-MEMORY» Request
Page 311 and 312:
Exchanges by Protocol Transmission
Page 313 and 314:
Return code If OK Code Report messa
Page 315 and 316:
TRANSMISSION (PORT 0x30) TRANSMISSI
Page 317 and 318:
Structure of the Transmission Buffe
Page 319 and 320:
Structure of the Reception Buffer B
Page 321 and 322:
Exchanges by Protocol 15.5.4 Settin
Page 323 and 324:
Programming in C Language 16 Progra
Page 325 and 326:
16.1 General Programming in C Langu
Page 327 and 328:
16.4 Programming in C 16.4.1 Concep
Page 329 and 330:
16.4.3 Exchange Area Programming in
Page 331 and 332:
16.4.9 Library Functions Programmin
Page 333 and 334:
16.4.9.2 Using System Functions Exa
Page 335 and 336:
Programming in C Language Read an I
Page 337 and 338:
Programming in C Language Initialis
Page 339 and 340:
Programming in C Language Draw a Ci
Page 341 and 342:
Programming in C Language Colour an
Page 343 and 344:
Programming in C Language Read an A
Page 345 and 346:
Programming in C Language End a Cri
Page 347 and 348:
Programming in C Language Semaphore
Page 349 and 350:
Programming in C Language REMARKS I
Page 351 and 352:
Programming in C Language Write a F
Page 353 and 354:
Description of a Directory File A d
Page 355 and 356:
17.1 General The PLC axis programmi
Page 357 and 358:
18 Programme Debugging 18.1 Program
Page 359 and 360:
Programme Debugging 18.1 Programme
Page 361 and 362:
18.2.2 Monitoring CPU Operation Thi
Page 363 and 364:
Programme Debugging Messages Commen
Page 365 and 366:
Requirements «PLC OPERATION» menu
Page 367 and 368:
18.2.3 Monitor and %TS Task Times P
Page 369 and 370:
18.2.4 File Management This functio
Page 371 and 372:
18.2.4.2 Application Directory This
Page 373 and 374:
18.2.5 Input/Output Configuration T
Page 375 and 376:
Example Identification of rack 0 an
Page 377 and 378:
18.2.6.1 Software Backup Actions Se
Page 379 and 380:
Select the module to be animated us
Page 381 and 382:
Load a new Ladder module Press «F2
Page 383 and 384:
Write a Variable Press «F10». ☞
Page 385 and 386:
19.1 List of Hardware Errors ERR_BU
Page 387 and 388:
Lists of Functions A Lists of Funct
Page 389 and 390:
A.1 List by Themes A.1.1 General Pu
Page 391 and 392:
A.1.6 Interrupt Input Management Li
Page 393 and 394:
Lists of Functions Function Descrip
Page 395 and 396:
Symbols %I Organisation 3-15 %INI 2
Page 397 and 398:
L Label 4-3 Ladder module structure
show all

Automatic control function programming manual ladder language

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?