Automatic control function programming manual ladder language

More documents

Recommendations

Info

9.4 Read an Analogue Input anai Syntax 9 - 6 en-938846/7 anai(cch, &winput) cch: Input address encoded on one byte. &winput: Address of a variable (%Mxxx.W or %Vxxx.W) to be loaded with the value of the input on 16 signed bits. Operation Reads an analogue input. Card location Channel number Bit 7 Bit 0 Refer to the Installation and Commissioning Manual for the card location on the system bus. The values 0 to 7 correspond to the channel numbers of the eight input registers or eight output registers. Example anai(0x37, %V100.&) Reads input 7 from card 3 and loads the result into %V100.W. Return code If OK 0 Error 1: Card absent. 2: Card parameter error. 3: Channel parameter error. Programming error causing a CPU fault Access to a prohibited address: - &winput parameter error.
Analogue Inputs/Outputs 9.5 Reassign an Analogue Card anaa Syntax anaa(initial_cch, future_cch) initial_cch: Byte containing the card No. (the channel number is not significant). future_cch: Byte containing the card No. (the channel number is not significant). Operation Reassigns an analogue card. This function is optional. It is used to reassign functions anas(initial_cch, ...), anao(initial_cch, ...), anai(initial_cch, ...) to card future_cch. Detail of the «initial_cch» and «future_cch» arguments ! CAUTION This function is authorised only in PLC task %INI. Card location Channel number Bit 7 Bit 0 Refer to the Installation and Commissioning Manual for the card location on the system bus. The values 0 to 7 correspond to the channel numbers of the eight input registers or eight output registers. Return code If OK 0 Error 1: Final card absent. 2: Card parameter error. 4: Function called in a task other than an %INI task. en-938846/7 9 - 7 9
Page 1 and 2:
NUM AUTOMATIC CONTROL FUNCTION PROG
Page 3 and 4:
Table of Contents Table of Contents
Page 5 and 6:
Table of Contents 9 Analogue Inputs
Page 7 and 8:
Record of Revisions Record of Revis
Page 9 and 10:
Date Revision Reason for revisions
Page 11 and 12:
Structure of the NUM 1020/1040/1060
Page 13 and 14:
Automatic Control Function Programm
Page 15 and 16:
CHAPTER 8 TRANSPARENT MODE CHAPTER
Page 17 and 18:
CHAPTER 16 PROGRAMMING IN C LANGUAG
Page 19 and 20:
Use of the Automatic Control Functi
Page 21 and 22:
Presentation of the Automatic Contr
Page 23 and 24:
1.1 General Presentation of the Aut
Page 25 and 26:
AXIS 1 INTERFACE AXIS 2 AXIS 3 AXIS
Page 27 and 28:
µ p 68020 SYSTEM BUS BUS INTERFACE
Page 29 and 30:
Structure of an Application 2 Struc
Page 31 and 32:
2.1 General The machine processor c
Page 33 and 34:
2.1.1.3 «System» I/O Card Refresh
Page 35 and 36:
Operation of the Background Tasks N
Page 37 and 38:
2.1.2.4 Real-Time Tasks Structure o
Page 39 and 40:
2.1.3.2 1060 Series II- UCSII Syste
Page 41 and 42:
2.2 Structure of an Application Str
Page 43 and 44:
2.3 Structure of a Ladder Module -
Page 45 and 46:
Variables 3 Variables 3.1 Principle
Page 47 and 48:
Variables 3.8.2.19 Backward of Forw
Page 49 and 50:
3.1 Principle of Exchanges Variable
Page 51 and 52:
Examples %M9 points to byte 9 of th
Page 53 and 54:
3.7 I/O Card Interface Variables %I
Page 55 and 56:
3.7.3.2 Card Status %Irc3C.W Variab
Page 57 and 58:
A configuration change requires mov
Page 59 and 60:
3.7.5 Physical Organisation of Vari
Page 61 and 62:
3.7.6 Rack and Card Identifiers 3.7
Page 63 and 64:
3.7.8 Image Part of the 32 Discrete
Page 65 and 66:
%Qrc00.0 to %Qrc02.7 %Irc00.0 to %I
Page 67 and 68:
%Qrc03.0 to %Qrc05.7 2nd relay modu
Page 69 and 70:
3.7.12 Image Part of the Extension
Page 71 and 72:
3.7.13 Image Part of the Compact Pa
Page 73 and 74:
3.8 CNC I/O Interface Family %R and
Page 75 and 76:
Variables Variable Mnemonic Descrip
Page 77 and 78:
3.8.1.7 Spindle Status: %R12.W Vari
Page 79 and 80:
3.8.1.10 Other Variables Variables
Page 81 and 82:
3.8.1.13 1050 Servo-Drive Status Wo
Page 83 and 84:
Variable Mnemonic Description %W3.0
Page 85 and 86:
3.8.2.4 Negative JOG Commands: %WA.
Page 87 and 88:
Programme %9999.9 must be structure
Page 89 and 90:
3.8.2.13 Spindle Controls: %W22.W V
Page 91 and 92:
- Select spindle b control: COMBRb
Page 93 and 94:
3.8.2.16 Modes Inhibited: %W30.L Va
Page 95 and 96:
3.8.2.19 Backward of Forward Moveme
Page 97 and 98:
3.8.3 Inputs from the Axis Groups V
Page 99 and 100:
3.8.3.4 Encoded M Function Without
Page 101 and 102:
Nonmodal functions A nonmodal funct
Page 103 and 104:
Variables Variable M function Defin
Page 105 and 106:
3.8.4 Outputs to the Axis Groups Th
Page 107 and 108:
3.8.5 System Faults and Diagnostic
Page 109 and 110:
3.8.7 Output Card Write Enable: %W9
Page 111 and 112:
3.8.10 Physical Organisation of %R
Page 113 and 114:
3.9.3 Organisation of %S Common Wor
Page 115 and 116:
Language element Includes Comment V
Page 117 and 118:
B4_ARR B3_ARR B2_ARR B1_ARR B4_ROT
Page 119 and 120:
3.11.3 Output to the CNC CHG_ C_ C-
Page 121 and 122:
VER VER VER VER STOP STOP STOP STOP
Page 123 and 124:
3.11.4 PLC-CNC Exchange Area - 1050
Page 125 and 126:
M63 M62 M65 M64 %Rg24.7 %Rg24.6 %Rg
Page 127 and 128:
Literal Elements of Ladder Language
Page 129 and 130:
4.1 Notations Used The notations us
Page 131 and 132:
Literal Elements of Ladder Language
Page 133 and 134:
4.5.5 Order of Evaluation of the Ex
Page 135 and 136:
4.5.8 Overflow - Sign Change Litera
Page 137 and 138:
Programming in Ladder Language 5 Pr
Page 139 and 140:
5.1 Elements Common to All Types of
Page 141 and 142:
Programming in Ladder Language en-9
Page 143 and 144:
5.2 Network Sequence 5.2.1 General
Page 145 and 146:
Example 5.2.2.3 Conditional Actions
Page 147 and 148:
Off Timeout «TOF_n» E Q %TQxx.7 T
Page 149 and 150:
Upcounters E C Q %CQxx.7 Threshold
Page 151 and 152:
5.2.3 Structure of the Action Zone
Page 153 and 154:
Pitfall Related to Scanning Program
Page 155 and 156:
Invalid Network - Branch without Po
Page 157 and 158:
5.2.7 Programming Hints 5.2.7.1 Opt
Page 159 and 160:
Unoptimised Network Optimised Netwo
Page 161 and 162:
5.2.7.4 Testing the Bits of a Byte,
Page 163 and 164:
General Purpose Functions 6 General
Page 165 and 166:
General Purpose Functions 6.1 Conve
Page 167 and 168:
General Purpose Functions 6.3 BCD
Page 169 and 170:
General Purpose Functions 6.5 Separ
Page 171 and 172:
General Purpose Functions 6.7 Copy
Page 173 and 174:
Page 175 and 176:
Return code If OK Number of charact
Page 177 and 178:
General Purpose Functions 6.14 Simu
Page 179 and 180:
General Purpose Functions 6.17 Sear
Page 181 and 182:
General Purpose Functions 6.20 Jump
Page 183 and 184:
Return code If OK Not significant.
Page 185 and 186:
Return code If OK Value returned by
Page 187 and 188:
Return code If OK Number of charact
Page 189 and 190:
Page 191 and 192:
General Purpose Functions 6.34 Swap
Page 193 and 194:
General Purpose Functions 6.36 Read
Page 195 and 196: General Purpose Functions 6.38 Init
Page 197 and 198: Task Management 7 Task Management 7
Page 199 and 200: 7.1 Introduction Task Management Fo
Page 201 and 202: Transparent Mode 8 Transparent Mode
Page 203 and 204: 8.1 Introduction Transparent Mode T
Page 205 and 206: 8.1.4 Character Codes Used by %R0.W
Page 207 and 208: 8.2 Functions Assigned to transpare
Page 209 and 210: Transparent Mode Operation Sends a
Page 211 and 212: Example 1 Consider the following va
Page 213 and 214: Transparent Mode 8.2.7 Open a Numer
Page 215 and 216: Return code Transparent Mode If OK
Page 217 and 218: Transparent Mode Operation putimage
Page 219 and 220: en-938846/7 8 - 19 Transparent Mode
Page 221 and 222: 471 470 89 76 40 0 4 16 COL. 0 A A
Page 223 and 224: Transparent Mode Description Instru
Page 225 and 226: 8.3.4 Alphanumeric Characters and I
Page 227 and 228: Format D (Expanded characters) 0x9B
Page 229 and 230: Example To position the cursor on L
Page 231 and 232: Definition of a Reference System Ce
Page 233 and 234: J: «J» [VALUE] Current Y coordina
Page 235 and 236: 8.3.5.8 Shift Screen Origin Instruc
Page 237 and 238: P2 P1 P1 P2 P1 P2 N1 P3 P1 N6 P0 P0
Page 239 and 240: ! CAUTION Arguments [CLIP], [X] and
Page 241 and 242: Analogue Inputs/Outputs 9 Analogue
Page 243 and 244: 9.1 General Analogue Inputs/Outputs
Page 245: Analogue Inputs/Outputs 9.3 Write a
Page 249 and 250: Explicit Read/Write of Input/Output
Page 251 and 252: 10.1 General Explicit Read/Write of
Page 253 and 254: Explicit Read/Write of Input/Output
Page 255 and 256: Interrupt Inputs 11 Interrupt Input
Page 257 and 258: 11.1 General The automatic control
Page 259 and 260: 11.2 Principle of Line Assignment N
Page 261 and 262: Example Filtering on rising edge T1
Page 263 and 264: Interrupt Inputs 11.6 Associate a %
Page 265 and 266: Serial Lines 12 Serial Lines 12.1 G
Page 267 and 268: 12.1 General The automatic control
Page 269 and 270: Detail of the «format» argument 0
Page 271 and 272: PERIPHERAL Transmission to peripher
Page 273 and 274: Copy requested No. into buffer Yes
Page 275 and 276: Serial Lines 12.6 Control the Seria
Page 277 and 278: Serial Lines 12.7.2.3 Xon/Xoff Flow
Page 279 and 280: 13.1 General Description of the Tim
Page 281 and 282: 14.1 General Description of the Dat
Page 283 and 284: Exchanges by Protocol 15 Exchanges
Page 285 and 286: 15.1 General Description of Exchang
Page 287 and 288: 15.1.2 DNC1000 Exchange Mechanism E
Page 289 and 290: 15.2 Objects Accessible by a UNITE
Page 291 and 292: 15.2.2 Object Constituents The IU c
Page 293 and 294: Exchanges by Protocol Segment Acces
Page 295 and 296: Exchanges by Protocol Segment Acces
Page 297 and 298:
Detailed List of G Functions Presen
Page 299 and 300:
Example of reading the current prog
Page 301 and 302:
15.3.3 «DELETE-FILE» Request Used
Page 303 and 304:
Negative answer ANSWER CODE (1 byte
Page 305 and 306:
Request format Answer format Positi
Page 307 and 308:
15.3.8 «READ-BLOCK» Request Used
Page 309 and 310:
15.3.10 «RESERVE-MEMORY» Request
Page 311 and 312:
Exchanges by Protocol Transmission
Page 313 and 314:
Return code If OK Code Report messa
Page 315 and 316:
TRANSMISSION (PORT 0x30) TRANSMISSI
Page 317 and 318:
Structure of the Transmission Buffe
Page 319 and 320:
Structure of the Reception Buffer B
Page 321 and 322:
Exchanges by Protocol 15.5.4 Settin
Page 323 and 324:
Programming in C Language 16 Progra
Page 325 and 326:
16.1 General Programming in C Langu
Page 327 and 328:
16.4 Programming in C 16.4.1 Concep
Page 329 and 330:
16.4.3 Exchange Area Programming in
Page 331 and 332:
16.4.9 Library Functions Programmin
Page 333 and 334:
16.4.9.2 Using System Functions Exa
Page 335 and 336:
Programming in C Language Read an I
Page 337 and 338:
Programming in C Language Initialis
Page 339 and 340:
Programming in C Language Draw a Ci
Page 341 and 342:
Programming in C Language Colour an
Page 343 and 344:
Programming in C Language Read an A
Page 345 and 346:
Programming in C Language End a Cri
Page 347 and 348:
Programming in C Language Semaphore
Page 349 and 350:
Programming in C Language REMARKS I
Page 351 and 352:
Programming in C Language Write a F
Page 353 and 354:
Description of a Directory File A d
Page 355 and 356:
17.1 General The PLC axis programmi
Page 357 and 358:
18 Programme Debugging 18.1 Program
Page 359 and 360:
Programme Debugging 18.1 Programme
Page 361 and 362:
18.2.2 Monitoring CPU Operation Thi
Page 363 and 364:
Programme Debugging Messages Commen
Page 365 and 366:
Requirements «PLC OPERATION» menu
Page 367 and 368:
18.2.3 Monitor and %TS Task Times P
Page 369 and 370:
18.2.4 File Management This functio
Page 371 and 372:
18.2.4.2 Application Directory This
Page 373 and 374:
18.2.5 Input/Output Configuration T
Page 375 and 376:
Example Identification of rack 0 an
Page 377 and 378:
18.2.6.1 Software Backup Actions Se
Page 379 and 380:
Select the module to be animated us
Page 381 and 382:
Load a new Ladder module Press «F2
Page 383 and 384:
Write a Variable Press «F10». ☞
Page 385 and 386:
19.1 List of Hardware Errors ERR_BU
Page 387 and 388:
Lists of Functions A Lists of Funct
Page 389 and 390:
A.1 List by Themes A.1.1 General Pu
Page 391 and 392:
A.1.6 Interrupt Input Management Li
Page 393 and 394:
Lists of Functions Function Descrip
Page 395 and 396:
Symbols %I Organisation 3-15 %INI 2
Page 397 and 398:
L Label 4-3 Ladder module structure
show all

Automatic control function programming manual ladder language

Create successful ePaper yourself

Delete template?

Save as template?