FDR V54L78 - Innovation Data Processing
FDR V54L78 - Innovation Data Processing
FDR V54L78 - Innovation Data Processing
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>FDR</strong>927<br />
Reason:<br />
Action:<br />
MESSAGES AND CODES<br />
MESSAGES FROM SAR (<strong>FDR</strong>9NN) 100.4<br />
ENTER ABSOLUTE TRACK ADDRESS IN DECIMAL - ENTER ***END TO PROCESS<br />
You requested an absolute track operation. The message “STARTING CCHH=CCCCCHHHH” is<br />
displayed.<br />
Replace the CCCCCHHHH with the cylinder (5 digits) and head/track (4 digits) in decimal.<br />
After ENTER is depressed, SAR displays the ENDING CCHH= message; the ending<br />
cylinder and head/track is then entered. Up to 10 absolute ranges may be specified. When<br />
the last range is entered, reply “***END” to the STARTING CCHH= message.<br />
<strong>FDR</strong>928 MAXIMUM NUMBER OF ENTRIES EXCEEDED - ENTER ***END TO PROCESS<br />
Reason: You have entered the maximum number of entries (10) for data set names or absolute<br />
track ranges.<br />
Action: You must enter “***END” for SAR to process the data sets or tracks specified.<br />
<strong>FDR</strong>929 RESTORED CYL=cccc TRK - 0....5....ABCDEF0....5....ABCDEF<br />
Reason: On absolute track operations, SAR displays each cylinder processed (“cccc” is the<br />
cylinder number in hex). An “X” is printed in the appropriate column for each track<br />
restored within the cylinder.<br />
<strong>FDR</strong>930 TRACK TABLE ERROR<br />
Reason: A cylinder and head address was encountered on the backup tape that exceeded the<br />
track capacity of the disk volume.<br />
Action: If a hardcopy device was assigned, use the hardware PSW RESTART function to take a<br />
storage dump. Contact INNOVATION DATA PROCESSING for assistance.<br />
<strong>FDR</strong>931 VALID RESPONSE=responses<br />
Reason: This is an informative message to indicate the responses that are valid for the current<br />
console message. SAR may not display all of the possible responses. Chapter 30<br />
“<strong>FDR</strong>REORG®” of the <strong>FDR</strong> manual details all of the allowed responses to a message.<br />
Action: Enter the appropriate response.<br />
VALID RESPONSE=xxxxxx -- IDENTIFIED BY SAR<br />
Reason: The device type “xxxxxx” was determined by SAR to be the actual type of the disk<br />
device you input. It should not be overridden, except as discussed under “Alternate<br />
Device Support” in Section 15.1 “SAR Technical Description”.<br />
<strong>FDR</strong>932 I/O ERROR ON DISK TRACK X'cccchhhh' - REPLY CONTINUE OR TERM<br />
Reason: A logical or physical hardware error occurred on the disk track at cylinder “cccc” and<br />
track “hhhh” (in hex). A <strong>FDR</strong>951-<strong>FDR</strong>990 error message may have been displayed<br />
detailing the error. SAR did not backup or restore the indicated track properly.<br />
Action:<br />
SAR prompts you for a reply. Reply “CONTINUE” to ignore the error and continue with the next<br />
disk track (the contents of the bad track is not dumped or may be improperly restored), or<br />
“TERM” to terminate SAR with an error. If you have a hardcopy device assigned, you can use<br />
the hardware PSW RESTART function to take a storage dump before replying.<br />
<strong>FDR</strong>933 TAPE MOUNTED FOR usage status DSN=dsname<br />
REPLY YES FOR SAR TO USE IT AS type - NO TO REJECT - EXPDT=yyddd<br />
Reason: SAR displays the current data set name (last 17 characters from the tape label) for each<br />
tape mounted. “usage” may be HARDCPY, DUMP, or RESTORE.<br />
“status” indicates whether SAR detected labels on the tape and can be:<br />
IS VOL=vvvvvv – For a labeled tape.<br />
CHAPTER 100 – PAGE 100-119 –