FDR V54L78 - Innovation Data Processing

MESSAGES AND CODES
MESSAGES FROM FDR, DSF, AND ABR (FDRNNN) 100.3
Action:
N FDRINSTANT I/O ERROR – An I/O error occurred while performing the
FDRINSTANT backup.
P FDRINSTANT LABEL NOT FDR1 – FDRINSTANT changes the VOL1
label on the output volume to FDR1 when you do a SNAP, SPLIT, PSPLIT,
or FCOPY so it cannot be brought online by accident. But during the backup
phase of FDRINSTANT, the volume label was not FDR1 as expected.
Y UNABLE TO SPLIT – SPLIT RETRY COUNT EXCEEDED – Because of
conditions within the Symmetrix, FDR was forced to re-establish and re-split
the BCV a number of times, but the retry limit for this re-establish/re-split
was reached before a valid split BCV was created.
The backup is terminated (except for reason “D”). Many of these errors indicate that the
FDRINSTANT jobs have not been run in the correct order or with the correct
parameters. Correct the error, if possible, and rerun. Otherwise, contact
INNOVATION DATA PROCESSING Technical Support.
If you attempted to do a SNAP, SPLIT, PSPLIT, or FCOPY, but it failed for some
reason, then the DUMP step gets this message with reason “E” or “F”. Check the
output of the SNAP, SPLIT, PSPLIT, or FCOPY step to determine the cause of the
error. However, reason F is normal if the DUMP step fails after processing some
volumes, and you resubmit it; ABR gets reason “F” for the SNAP, SPLIT, PSPLIT, or
FCOPY volumes it has already processed and automatically bypasses them.
FDR212 program ERROR UNIT=uuuu REASON=reason
Reason: FDRINSTANT had an error attempting to process a volume on the device address
shown as “uuuu”, for the reason shown. Reason codes include:
F BCV VOLUME NOT FOUND OR NOT CONNECTED TO BCV – A DUMP
with BCV=USE is being executed, but FDR is not able the find the BCV.
Probably a BCV ESTABLISH was never done on the online device.
G ERROR DURING SPLIT PROCESSING – A PSPLIT operation has been
performed, but the units are not in the correct state. Check return and
reason codes for explanation of failure.
H BCV MATCHING BCV VOLUME NOT FOUND IN UCBVTOC – When a
BCV SPLIT is done the UCBVTOC field in the BCV is updated to point back to the
online UCB, but no offline disk had a pointer to the online disk you are dumping.
I LOAD FAILURE FOR MODULE EMCSAI/EMCQCAPI – FDR was unable
to load an EMC API module. The EMC libraries must be in the system
linklist or a STEPLIB in the FDR step.
K EMC CODE nn - reason – A BCV operation was requested, but the BCV
request to the Symmetrix subsystem failed with the indicated reason code
“nn”. “reason” is a brief text explanation of the reason.
L CANNOT SPLIT VOLUME PAIR NOT ESTABLISHED – A SPLIT operation
was requested, but the primary volume was never ESTABLISHed with an
FDRINSTANT volume or the volume has been reused with a different primary
volume.
N ESTABLISH TO BCVUNIT ALREADY IN USE – FDR attempted to do an
ESTABLISH of the online volume to the identified BCV, but the BCV was
already established to a different volume.
O VOL1 LABEL RESERVED FIELDS NOT BLANKS – When ABR does a
SPLIT, it records some information in the volume label of the offline disk.
During the ABR dump, the fields are not filled in. This is only a warning.
U ERROR INVALIDATING VOL1 LABEL – An I/O error occurred when
FDRINSTANT was attempting to modify the volume label of the
FDRINSTANT volume to insure that it cannot come online accidentally.
V CANNOT RESTORE VOLUME IS NOT SPLIT – A request to restore from
a captured volume image on an FDRINSTANT volume failed because that
volume is currently ESTABLISHed to a volume.
CHAPTER 100 – PAGE 100-47 –