FDR V54L78 - Innovation Data Processing

MESSAGES AND CODES
MESSAGES FROM FDR, DSF, AND ABR (FDRNNN) 100.3
FDR332 function SCRATCH status ON DSN=dsname
Reason: An attempt to delete a non-VSAM data set FAILED or was BYPASSED. FDR deletes
data sets during an FDRCOPY MOVE, an Archive Backup (DUMP TYPE=ARC), or
ABR Superscratch (DUMP TYPE=SCR).
“status” of FAILED indicates that a SCRATCH SVC (for non-SMS data sets) or DELETE
NVR or NONVSAM (for SMS-Managed data sets) failed to scratch this data set. An FDR
mini-dump is printed showing the registers and SCRATCH or DELETE parameter list.
Action:
For a non-SMS data set, the SCRATCH status code appears in the mini-dump, in the first line of
the storage display after the registers, in the second byte of the last word (right most word).
❖
❖
Code 1 indicates that the data set was not found in the VTOC.
Code 7 indicates that SCRATCH failed because the data set was in use; this can
be avoided by using the DSNENQ= option.
❖ Code 2 or 8 indicates a security violation.
For an SMS data set, register 15 (R15) contains the DELETE return code, and the
reason code is in the last 2 bytes of the 6th word of the first line of the storage dump
after the registers, in hex. These codes can be found under message IDC3009I in the
IBM messages manual after converting the codes to decimal.
❖ For Archive Backup, ABR has backed up the data set and recorded it in the
Archive Control File. This data set may have been uncataloged or recataloged for
recall as indicated by message FDR314.
❖ For Superscratch, this data set may have been uncataloged as indicated by
message FDR314.
❖ For FDRCOPY MOVE, if the data set was cataloged, it has been successfully
recataloged and/or uncataloged.
A “status” of BYPASSED indicates that the scratch was not attempted for this data set,
because of an earlier error, such as a catalog error that is described by another message.
If appropriate, scratch the data set manually. If desired, contact INNOVATION DATA
PROCESSING for assistance.
FDR333 CARD IMAGE--control statement image
Reason: Displays a control statement read from an ABR remote queue data set (DDname
ABRREST for RESTORE TYPE=ABR, ABRARCH for RESTORE TYPE=ARC,
ABRBKDQ for DUMP TYPE=ABR/AUTO, ABRARDQ for DUMP TYPE=ARC).
FDR334 FDR FAILED TO CATALOG comp DSN=dsname status
Reason: FDR allocated and restored the non-VSAM data set “dsname”, but could not catalog it.
If “comp” is printed, it is COMP=x'ffff00001111' that contains the catalog return codes
from registers R15 (ffff), R0 (0000), and R1 (1111). If the register 15 value is x'FF14',
then the code was generated by FDR, and indicates either that the data set was
currently cataloged on zero volumes or more than 255 volumes, or that the volume
sequence number of the current piece of the data set was higher than 255; the R0
value is the number of volumes currently in the catalog entry (in hex). FDR supports
cataloging of multi-volume data sets up to a maximum of 255 volumes.
If “status” is ALREADY CATALOG VOL=vvvvvv then RECAT was not specified, and
the output data set was already cataloged to a volume “vvvvvv” other than the output
volume (or the input volume for a MOVE). For a multi-volume data set, “vvvvvv” is the
volume in the catalog entry that corresponds to the volume sequence number of the
portion of the data set that has just been processed.
If “status” is NAME IS AN ALIAS then the data set name being cataloged was an alias
of another data set in the catalog so FDR did not update it.
Action: Determine the cause and take appropriate action. If desired, contact INNOVATION
DATA PROCESSING for assistance.
CHAPTER 100 – PAGE 100-71 –