FDR V54L78 - Innovation Data Processing

FDR224
Reason:
Action:
MESSAGES AND CODES
MESSAGES FROM FDR, DSF, AND ABR (FDRNNN) 100.3
FDR VOL=vvvvvv IS BEING DUMPED FROM ONLINE UNIT BECAUSE
SNAP/SPLIT/PSPLIT/FCOPY NEVER DONE
A FDRABR DUMP is being executed with SNAP=USE, PPRC=USE, FCOPY=USE,
and/or BCV=USE but the identified volume is not eligible for FDRINSTANT
processing. It is issued for every volume in the backup step that has not had a SNAP,
SPLIT, PSPLIT, or FCOPY executed against it successfully.
This message is issued for all normal volumes (volumes that you want regular backups,
not FDRINSTANT) that are processed in the same step with FDRINSTANT volumes,
unless you have erroneously attempted to do a SNAP, SPLIT, PSPLIT, or FCOPY of
those ineligible volumes.
The message is also issued for all eligible volumes for which SNAP, SPLIT, PSPLIT, or
FCOPY has never been done, indicating that you want to backup those volumes normally.
The volume is backed up by normal ABR backup processing, but it is not a point-in-time backup.
If the message identifies a volume that you did not intend to backup with FDRINSTANT,
it can be ignored.
If you did intend to use FDRINSTANT on this volume, check your SNAP, SPLIT,
PSPLIT, or FCOPY step to be sure that it was included.
NOTE: If you attempted a SNAP, SPLIT, PSPLIT, or FCOPY but it failed for some reason,
ABR fails that backup with message FDR211 REASON=E or F assuming that you
wanted a point-in-time backup. Check the output of the SNAP, SPLIT, PSPLIT, or
FCOPY step to determine the failure.
FDR225 FDRINST DID NOT action OFFLINE type UNIT=uuuu - OFFLINE BACKUP IS IN USE
Reason: A FDRABR DUMP is being executed with SNAP=(USE,REL), PPRC=(USE,RET),
FCOPY=(USE,REL) or BCV=(USE,RET) (or both) but at the end of the backup, ABR
could not release the copied volume or RE-ESTABLISH the BCV because another
task has the backup data set enqueued, probably because of a restore.
Action: You should RE-ESTABLISH the BCV or release the copied volume later when the
backup data set is no longer in use.
FDR230 program type UNIT=uuuu REASON=reason
Reason: FDRINSTANT had an error attempting to use special hardware facilities to get a
point-in-time image of a volume for FDRINSTANT use. “type” is “WARNING” or
“ERROR”. “uuuu” is the device address of the target disk and “reason” indicates the
cause. Note that some reason codes have several versions depending on the
hardware facility that failed. Reason codes include:
1 MOUNT STATEMENT NOT SPECIFIED – There were no MOUNT statements
following a SNAP, SPLIT, PSPLIT, or FCOPY statement. MOUNT statements are
used to define the source volume and target device for the FDRINSTANT copy.
2 MOUNT STATEMENT NOT FOUND – Some control statements were provided
after the SNAP, SPLIT, PSPLIT, or FCOPY statement, but none of them were
MOUNT statements. Only MOUNT statements can follow that statement.
3 xxxxUNIT= NOT SPECIFIED IN MOUNT STATEMENT – A MOUNT
statement does not contain the operand SNAPUNIT=, PPRCUNIT=,
FLASHUNIT=, or BCVUNIT=. It is required.
4 SOURCE AND type UNIT ADDRESS ARE EQUAL – The unit on which
the volume specified by VOL= is mounted is the same as the unit specified
by xxxxUNIT=. A volume cannot be copied to itself.
5 INCOMPATIBLE SOURCE AND type UNIT DEVICE TYPES – The device
type of the unit on which the volume specified by VOL= and the unit
specified by xxxxUNIT= are not the same. You cannot snap from a 3380 to
a 3390 or vice versa.
CHAPTER 100 – PAGE 100-49 –