FDR V54L78 - Innovation Data Processing

MESSAGES AND CODES
MESSAGES FROM FDR, DSF, AND ABR (FDRNNN) 100.3
H MESSAGE ID=mmmm COMPLETION CODE=cccc REASON=rrrr –
ECAM message number “mmmm” was issued to the SnapShot device. The
message was rejected with completion code “cccc” and reason code “rrrr”.
Contact INNOVATION DATA PROCESSING for assistance.
I MESSAGE ID=mmmm PARMID=pppp COMP CODE=cccc REASON=rrrr –
ECAM message number “mmmm” was issued to the SnapShot device. The
message was rejected because of a problem with message parameter
“pppp” with completion code “cccc” and reason code “rrrr”. Contact
INNOVATION DATA PROCESSING for assistance.
J
TARGET UNIT HAS LESS CYLINDERS THAN SOURCE DEVICE – The
source volume specified by VOL= has more cylinders than the target
volume specified by SNAPUNIT=. The target volume must be equal to or
larger than the source volume in size.
K UNDEFINED SNAPSHOT STATUS – Unexpected response from the
SnapShot device.
L UNDEFINED SNAPSHOT MESSAGE COUNT – Unexpected response
from the SnapShot device.
M
EXPECTED MSGID=nnnn. RECEIVED MSGID=nnnn – Unexpected
response from the SnapShot device; the wrong ECAM message was received.
N INVALID FDRINSTANT VOL1 LABEL OR GEN/CYCLE MISMATCH –
FDR changed the ID of the volume label of the target disk to FDR1 so that it
can't be accidentally brought online. When the point-in-time image was
dumped, the label was no longer FDR1, or the ABR generation and cycle
created during the SNAP, SPLIT, PSPLIT, or FCOPY was not the same as that
currently recorded on the target. Contact INNOVATION DATA PROCESSING if
you do not want FDRINSTANT to modify the volume label.
O
PRIOR FDRABR INSTANT BACKUP PENDING DSN=dsname – A DUMP
or SNAP, SPLIT, PSPLIT, or FCOPY was not done because a previous SNAP,
SPLIT, PSPLIT, or FCOPY had been done, but you have not yet executed the
DUMP to move the point-in-time backup to tape. If you want to do a DUMP
(non-FDRINSTANT) and discard the point-in-time backup, specify the operand
INSTANTLOSS=YES on the DUMP statement.
P PRIOR FDRABR INSTANT BACKUP IS LOST DSN=dsname – A DUMP
or SNAP, SPLIT, PSPLIT, FCOPY detected that a previous SNAP, SPLIT,
PSPLIT, FCOPY had been done, but you have not yet executed the DUMP to
move the point-in-time backup to tape. Since you replied “YES” to the FDRW02
message or specified CONFMESS=NO or INSTANTLOSS=YES, the
uncompleted backup is discarded and is no longer usable.
Q
Q
TOO MANY WRITES PENDING – While FDRCOPY was attempting to use
the EMCCOPY internal copy function on an EMC Symmetrix, the
Symmetrix reported that an internal limit of pending writes (from cache to
disk) was exceeded. The copy continues using normal read/write I/O.
CONTROLLER DOES NOT SUPPORT LRE/WFT – Contact INNOVATION
DATA PROCESSING for assistance.
R TARGET VOLSER DOES NOT MATCH SOURCE – The operand
VERIFYVOLSER=YES was specified, but the current volser of the offline
target does not match the volser of the online source volume.
R
S
DEVN/UNIT LOCATION ROUTINE ERROR FUNC=function – Contact
INNOVATION DATA PROCESSING for assistance.
PPRCUNIT IS NOT PAIRED WITH PRIMARY – The device specified by
PPRCUNIT= is not currently in a PPRC session with the primary volume. You
did not issue a previous (C)ESTPAIR command to establish the session.
S ANTRQST IS NOT INSTALLED AT LEVEL 4 – You do not have the
proper level of the IBM ANTRQST API to support FlashCopy installed.
Contact INNOVATION DATA PROCESSING for assistance.
CHAPTER 100 – PAGE 100-51 –