FDR V54L78 - Innovation Data Processing

MESSAGES AND CODES
MESSAGES FROM FDR, DSF, AND ABR (FDRNNN) 100.3
Action:
F –
G –
H –
I –
J –
K –
L –
M –
O –
P –
Q –
R –
S –
T –
U –
V –
An operand that requires numeric data (e.g., MAXCARDS=) specified nonnumeric
characters, or an operand that requires hexadecimal data (e.g.,
SNAPUNIT=) specified non-hex characters.
An operand did not end with a blank or comma or exceeded 15 digits (e.g.,
MAXCARDS=).
ADAYS= operand resulted in a negative year.
Keyword is invalid under the operation indicated. (e.g., GEN= was specified
on a DUMP operation). Check manual for allowable keywords under this
operation. Also, if the operation invokes ENCRYPTion, ensure that
RTC=YES is not specified since ENCRYPTion preforms its own
compression.
Control statement was completely blank. You can enter comment lines by
placing an * (asterisk) in column 1.
A required operand was not specified on the preceding SELECT statement.
On RESTORE TYPE=FDR, VOL= was not specified. On all other
operations DSN, DSG, DD, ALLDSN, or FROM/TO was not specified.
NEWG= began with a period.
COPY operand specified other than “1” or “2” on the SELECT command,
DSORG specified an invalid value, a date was improperly specified, the
data set specified by CATDSN= is cataloged on more than 255 volumes or
an invalid TAPEVOLGn= operand.
An operand was specified on a system that does not support it. For example,
SMSMANAGE=YES cannot be specified on a system where SMS is not active.
ALLDSN was specified without ADATE on RESTORE TYPE=ARC.
NEWN/G/I was specified with NEWNAME disabled. VOLG was specified on
a RESTORE TYPE=ABR or TYPE=FDR.
Keyword exceeded maximum value or was negative (e.g., GEN=10000 or
CYCLE=64).
TYPE=xxx was specified multiple times.
An operand on the SELECT statement was specified multiple times or was
mutually exclusive with another operand. (e.g., DSN and DSG were both
specified). DSN or DSG was specified on a MOUNT command.
The operand BACKUP appeared on a SELECT statement read during a
RESTORE TYPE=ARC operation or the operand ARCHIVE appeared on a
SELECT statement read during a RESTORE TYPE=ABR operation. The
operands BACKUP and ARCHIVE should only appear on restore requests
written to the remote queue restore data sets (ABRREST and ABRARCH),
respectively. Perhaps these two data sets were reversed.
The TYPE=xxx operand was missing or invalid on the first statement. This
operand is required for FDR, DSF, FDRCOPY, or ABR.
An absolute track keyword was specified to FDRDSF (FROM/TO). The
FROM/TO specification was in error. CYL and TRK did not specify numeric
values or FROM value was higher than TO value, or absolute track
operations have been disabled (NOABSTRK), or FROM/TO was specified
on an EXCLUDE statement (DUMP only).
Correct error and resubmit job. If you do not understand the error after reviewing the relevant
sections of this manual, call INNOVATION DATA PROCESSING for assistance.
NOTE: If the control statements look good and you can't see any obvious reason for the
error, check the JCL to be sure you are executing the right program for the
statements you provided (PGM=FDR, PGM=FDRDSF, PGM=FDRABR, etc.).
FDR303 CARD IMAGE – control statement image source
Reason: An input control statement is displayed by this message. “source” may be:
blank – From SYSIN.
PARM ENTRY – From the JCL PARM= operand.
PROTECT LIST – From an ABR protect list.
CHAPTER 100 – PAGE 100-58 –