FDR V54L78 - Innovation Data Processing

MESSAGES AND CODES
CHAPTER 100 – PAGE 100-95 –
MESSAGES FROM FDR, DSF, AND ABR (FDRNNN) 100.3
UNCATALOGED (SERVICE=UNCATLG) – User specified a RECATALOG
command with SERVICE=UNCATLG.
DATA FIELD MODIFY COMPLETED – User ran FDRTSEL or FDRTCOPY, which
invoked FDRARCH, that updated the Archive Control File to reflect the copied files.
FDR511 RECALL/BACKUP DATA SET function status--DSNAME=dsname
Reason: An FDRARCH function may create, update, or uncatalog the catalog entry for a data set
archived for auto-recall. An error occurred during this process so the catalog entry for
data set “dsname” was not disturbed. “function” is LOCATE, CATALOG, RECATLG,
UNCATALOG, or CVAFDIR. “status” is FAILED for an actual failure or IGNORED
when FDRARCH could not do the catalog update (an additional reason is displayed).
This message is always followed by message FDR516 or FDR674 to document the
error when “status” is FAILED.
Action: See message FDR516 or FDR674 if “status” is FAILED.
FDR512 WARNING--IMBEDDED INACTIVE BLOCK--ENTRY COUNT=nnn--RBN=rrr
Reason: The DUMP function encountered an imbedded block within a control file that is not
marked as containing data. The number of entries within the block is printed as “nnn”.
The relative block number within the control file is printed as “rrr”.
Action: This is a serious error. Call INNOVATION DATA PROCESSING for technical support.
FDR513 type TABLE CONTAINS nnnnnnnn ENTRIES
Reason: A reorganization of the Archive Control File is being performed and obsolete Archive
Backup data sets are to be uncataloged (UNCAT=YES). FDRARCH builds tables of
all Archive Backups it finds in the Archive Control File. The resulting table contains
“nnnnnnnn” entries. “type” may be TAPE for the full table of Archive Backup files, or
VOLSER for the table of unique backup volume serials.
FDR514 ARCHIVE TAPE function FAILED--DSNAME=dsname
Reason: A reorganization of the Archive Control File is being performed and obsolete Archive
Backup data sets are to be uncataloged (UNCAT=YES) but a catalog action failed on
the Archive Backup “dsname”. “function” may be:
UNCATALOG – Uncatalog of an obsolete Archive Backup failed.
SCRATCH – Scratch of an obsolete Archive Backup data set on disk failed.
CATALOG – An Archive Backup tape data set that is no longer required had been
uncataloged, but then it became necessary to catalog another Archive Backup
tape data set on the same volume. (Cataloging of Archive tape data sets is
done only to provide an entry in the catalog for a given tape volume serial and is
designed for those installations tape management catalog control retention).
Action: See message FDR516, FDR526, or FDR674 for details on the error.
FDR515 ARCHIVE TAPE action VOL=volser--DSNAME=dsname
Reason: A reorganization of the Archive Control File is being performed and obsolete Archive
Backup data sets are to be uncataloged (UNCAT=YES). “action” may be:
UNCATALOGED – An obsolete Archive Backup data set was uncataloged.
SCRATCHED – An obsolete Archive Backup data set on disk was scratched.
CATALOGED – An Archive Backup tape data set that is no longer required had
been uncataloged, but then it became necessary to catalog another Archive
tape data set on the same volume (see message FDR514 for explanation).
FDR516 function REGISTERS -- R0=xxxxxxxx R1=xxxxxxxx R15=xxxxxxxx
Reason: “function” may be:
CAMLST – A CAMLST request for a CATALOG operation or a SCRATCH failed.
CATLG or CATALOG – A request to catalog a data set failed.
LOCATE – A LOCATE request to read a catalog record failed.