FDR V54L78 - Innovation Data Processing
FDR V54L78 - Innovation Data Processing
FDR V54L78 - Innovation Data Processing
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
MESSAGES AND CODES<br />
<strong>FDR</strong> CONSOLE MESSAGES AND TSO TERMINAL MESSAGES 100.2<br />
<strong>FDR</strong>W42 THE <strong>FDR</strong> SYSTEM MODULES ARE status type<br />
Reason: This message is issued by <strong>FDR</strong>PARE or <strong>FDR</strong>STATS when the <strong>FDR</strong> operating system<br />
exit modules are disabled. This message is also issued by <strong>FDR</strong>START when<br />
activating or replacing the operating system exit modules.<br />
The “status” of the modules may be:<br />
NOT ACTIVE – When the ABR operating system exit modules are not installed in<br />
the system.<br />
INACTIVE – When the ABR operating system exit modules are installed in the<br />
system but are disabled, i.e., not processing any requests.<br />
REPLACED – When the ABR operating system exit modules have been replaced<br />
by running the <strong>FDR</strong>START program with the “REPLACE” parm.<br />
ACTIVE – When the ABR operating system exit modules are installed.<br />
RE-ACTIVATED – When the ABR operating system exit modules that were<br />
INACTIVE have been enabled so they process requests.<br />
DE-INSTALLED – When the ABR operating system exit modules are removed.<br />
“type” may indicate:<br />
PROD – For production exits.<br />
TEST – For test exits (the JOBNAME= or JOBGROUP= that use the test exists is<br />
also displayed).<br />
<strong>FDR</strong>W44 module ESTAE RECOVERY ENTERED FOR ABEND Ssss Uuuuu AT OFFSET xxxx<br />
Reason: This message is issued by “module”, which can be <strong>FDR</strong>START, <strong>FDR</strong>STATS, or<br />
<strong>FDR</strong>PARE, when an unexpected system “sss” or user “uuuu” ABEND occurs at<br />
displacement “xxxx” in the module. If the offset is not displayed, the ABEND did not<br />
occur within the <strong>FDR</strong>START module.<br />
Action: If the problem persists call INNOVATION DATA PROCESSING for assistance.<br />
<strong>FDR</strong>W46 module FAILURE - REASON=nn<br />
Reason: The execution of “module”, which can be <strong>FDR</strong>START, <strong>FDR</strong>STATS, or <strong>FDR</strong>PARE failed<br />
for one of the following reasons “nn”:<br />
01 O. S. NOT MVS SP 1.2 OR HIGHER –<br />
02 INVALID INPUT PARAMETERS – Check the PARM= specified.<br />
03 UNABLE TO OBTAIN AUTHORIZATION – Program library must be APF<br />
authorized.<br />
04 <strong>FDR</strong>VECTB VECTOR TABLE IS INVALID – Call INNOVATION DATA<br />
PROCESSING.<br />
05 SYSLIB DD MISSING OR OPEN ERROR – Check the SYSLIB DD statement.<br />
06 modname NOT FOUND IN SYSLIB – The ABR exit “modname” was not<br />
found in the library pointed to by the SYSLIB DD statement.<br />
07 modname MODULE LOAD ERROR: Ssss-rr – Call INNOVATION DATA<br />
PROCESSING.<br />
08 ERROR MODIFYING THE SVC TABLE – Call INNOVATION DATA<br />
PROCESSING.<br />
09 modname NOT FOUND – The module “modname” was not found in the<br />
link pack area. Call INNOVATION DATA PROCESSING.<br />
10 modname NOT FOUND IN THE LINKLIST – The ABR exit module<br />
“modname” was not found in an APF authorized LINKLIST library.<br />
11 modname - UNABLE TO DE-INSTALL – Call INNOVATION DATA<br />
PROCESSING.<br />
12 modname CDE OR LPDE ABOVE 16M ERROR – Call INNOVATION<br />
DATA PROCESSING.<br />
13 modname MODULE ABOVE 16M ERROR – Call INNOVATION DATA<br />
PROCESSING.<br />
14 GETMAIN ERROR – Increase the region in the step JCL.<br />
CHAPTER 100 – PAGE 100-6 –