FDR V54L78 - Innovation Data Processing
FDR V54L78 - Innovation Data Processing
FDR V54L78 - Innovation Data Processing
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
MESSAGES AND CODES<br />
<strong>FDR</strong> CONSOLE MESSAGES AND TSO TERMINAL MESSAGES 100.2<br />
<strong>FDR</strong>W04 FULL VOLUME RESTORE COMPLETED - UNIT=uuuu SHOULD BE REMOUNTED ON<br />
OTHER SYSTEMS<br />
Reason: A full volume restore was completed on the disk device “uuuu” that is marked as “Shared<br />
DASD” in your I/O configuration. <strong>FDR</strong> has determined that the restore changed the volume<br />
serial and/or the VTOC location on the output volume. <strong>FDR</strong> has made the necessary<br />
changes on the system where the restore was run, but if other CPUs access the disk, they<br />
do not know of this change and may not process this volume properly.<br />
Action: Normally all other systems should make this device offline prior to the restore, especially if the<br />
volume serial or VTOC changes. This message indicates that you may now remount the volume<br />
on the other systems; vary it OFFLINE if not already offline, then vary it ONLINE.<br />
<strong>FDR</strong>W05 DISK UNIT=uuuu VOL=vvvvvv HAS BEEN RELABELED TO VOL=nnnnnn<br />
Reason: Disk device “uuuu” has been restored. Its original volume serial was “vvvvvv” but the<br />
restore has changed the volume serial to “nnnnnn”.<br />
<strong>FDR</strong>W06 DISK UNIT=uuuu VOL=vvvvvv NOW OFFLINE - DUPLICATE VOLSER<br />
Reason: Disk device “uuuu” has been restored. The restore has changed the volume serial to “vvvvvv”,<br />
which matches the volser of another online volume (probably the original volume).<br />
Action: <strong>FDR</strong> sets disk device “uuuu” offline.<br />
<strong>FDR</strong>W10<br />
Reason:<br />
Action:<br />
<strong>FDR</strong>DRP COULD USE ADDITIONAL type TAPE DRIVES; PLEASE VARY SOME<br />
ONLINE IF AVAILABLE.<br />
A <strong>FDR</strong>DRP restore has not reached its limit of active tape drives (MAXTAPES=) but no<br />
additional drives of the needed type are online.<br />
Vary one or more tape drives online. After a few moments, <strong>FDR</strong>DRP begins to use them.<br />
<strong>FDR</strong>W22 DSN dsname PASSWORD PROTECTED<br />
Reason: <strong>Data</strong> set “dsname” is password protected and is being backed up or restored. This<br />
refers to old OS password protection for non-VSAM data sets and VSAM password<br />
protection for VSAM. It does not refer to security systems like IBM RACF.<br />
Action: To continue processing the operator must reply to the appropriate z/OS password message.<br />
<strong>FDR</strong>W23 DSN dsname DATE PROTECTED REPLY YES OR NO FOR ARCHIVE<br />
Reason: Non-VSAM data set “dsname” was selected for Archive or Superscratch, but the data set has<br />
an expiration date that has not been reached. If you wish to suppress this message and<br />
automatically select the data set, specify EXPD=NONE on the DUMP statement.<br />
Action: Reply “YES” – Archive and/or scratch the data set.<br />
Reply “NO” – DO NOT select the data set.<br />
<strong>FDR</strong>W24 <strong>FDR</strong>ABR REQUEST FOR TAPES - vvvvvv... REPLY YES NO OR BYPASS<br />
Reason: The OPERATOR operand was specified on a RESTORE statement. A restore of a data<br />
set was requested from the backup volumes “vvvvvv…”.<br />
Action: Reply “YES” – You have the volumes available.<br />
Reply “NO” – You do not have the volumes available, or do not wish to mount them at<br />
this time. The restore is cancelled.<br />
Reply “BYPASS” – same as NO.<br />
CHAPTER 100 – PAGE 100-4 –