FDR V54L78 - Innovation Data Processing

More documents

Recommendations

Info

MESSAGES AND CODES MESSAGES FROM FDR, DSF, AND ABR (FDRNNN) 100.3 Action: Q REBLOCK ERROR - reason – A logical restore error occurring while trying to re-block a data set (the BLKF= operand of RESTORE). “reason” briefly describes the error. R PDS DIRECTORY reason – A logical restore error occurred while processing the directory of a PDS (DSORG=PO). “reason” briefly describes the error. T TAPE BLOCK DEBLOCK ERROR – An FDR data block was improperly formatted. The backup may have been corrupted. U END OF FILE NOT FOUND ON INPUT – During a logical restore, an expected EOF record was not found within the dumped tracks of the data set; the data set may be usable. V VSAM ERROR reason – A logical restore error occurred while processing a VSAM cluster. “reason” briefly describes the error. W MISSING TTR – X DATA SET WAS EXCLUDED – Y TRACKS OUT OF ORDER FROM INPUT – On a logical restore, the tracks of the original non-VSAM data set were in multiple extents and not in ascending order on the backup or input disk. See “Action”. Correct the error, if possible, and rerun. If this was a logical restore or copy/move to an unlike device, it may be possible to do a physical restore/copy/move to a like device (same device type). If the error was due to multiple extents not in ascending order on a non-VSAM data set (REASON=Y or REASON=9), it may be possible restore or copy/move to a like device to reallocate the data set in a single extent then copy/move it to the unlike device (or use COMPAKTOR on the input disk to combine the extents of the data set). Read member UNLIKE in the Installation Control Library (ICL) for more details. Contact INNOVATION DATA PROCESSING if you need assistance. FDR139 TRACKIMAGE FORCED DSN=dsname REASON=7 BDAM VARIABLE OR UNDEFINED Reason: A logical restore of a BDAM (DSORG=DA) data set with variable or undefined format is done in track-image mode, restoring tracks exactly as they were dumped. Action: None. This is a warning only unless other errors occur. WARNING DSN=dsname REASON=7 CLUSTER NOT LOADED Reason: In this form of message FDR139, an attempt was made to perform a logical restore of an empty VSAM cluster. FDR only allocates and catalogs this cluster. Action: None. This is a warning only. WARNING DSN=dsn REASON=W MISSING TTR ttttrr FROM MEMBER=mem WARNING DSN=dsn REASON=W MISSING NOTE LIST TTR ttttrr Reason: In this form of message FDR139, during a logical restore or REORG of a PDS, a TTR pointer (relative track “tttt” and record number “rr”, both in hex) in the PDS directory or in a note list within a member did not point to any record in the original PDS. This is an error that existed in the PDS before FDR restored or reorganized the PDS. Action: The TTR is not changed. It is still invalid after the restore/reorg. All other members are processed. You should investigate the indicated member; it should probably be deleted. WARNING DSN=dsname REASON=U END OF FILE NOT FOUND ON INPUT Reason: In this form of message FDR139, during a logical restore of a PS or DA file, no EOF was found in the data set. However, all tracks were restored so the data set should be valid. WARNING DSN=dsname DATA=ALL IGNORED DUE TO DUMP OPTIONS Reason: In this form of message FDR139, during a logical restore DATA=ALL was specified, but the dump was not done with DATA=ALL. Action: DATA=ALL is ignored. The data set should be usable. REORG BYPASSED reason DSN=dsname Reason: In this form of message FDR139, an FDRCOPY REORG was requested for a data set, but it could not be done for the “reason” indicated: CHAPTER 100 – PAGE 100-28 –
FDR142 Reason: Action: MESSAGES AND CODES MESSAGES FROM FDR, DSF, AND ABR (FDRNNN) 100.3 PDSE – PDSEs are not supported for REORG. UNMOVABLE – The data set’s DSORG was POU. MODEL – The data set has no extents. NOT A PDS – The data set was not partitioned. ERROR USING THE READ MULTIPLE CKD COMMAND (5E) - NEW PERFORMANCE OPTION TERMINATED FDR detected an error using the 5E (RMCKD) command. This control unit may not support the command. FDR reverts to the previous performance option. Contact INNOVATION DATA PROCESSING for assistance. FDR149 API FORCED: xxxxxxxx xxxxxx0F RCxxxxxx xxxxxxxx xxxxxxxx EXCP REQUEST - CCW: xxxxxxxx xxxxxxxx RETINFO ANTF0xxxx error-description ANTRQST function-call TRACE - RTNCD=xxxx, RSNCD=xxx -- … EXCP FAILED - FUNCTION function CCW: xxxxxxxx xxxxxxxx IOB SENSE: xxxxxxxx xxxxxx0F RCxxxxxx xxxxxxxx xxxxxxxx NORMAL I/O PERFORMED - FLASH NOT ALLOWED tracedata INFO: FLASHCOPY TFT IS AN ACTIVE SRC Reason: FDR detected an I/O error while performing an FDRINSTANT operation. API FORCED – Re-attempt is performed and Sense Message Format (X'0F') and Reason Code (X‘RC') is displayed. IOB SENSE – I/O error detected - Sense Message Format (X'0F') and Reason Code (X'RC') is displayed. Common Reason Code values are: X'85' – An ESTABLISH could not be completed because the target is a PPRC primary or secondary volume, or an XRC primary volume X'A7' – An ESTABLISH could not be completed because the designated source track is already an existing target track X'AE' – An ESTABLISH could not be completed because the designated target track is already an existing target track X'AF' – An ESTABLISH could not be completed because the designated target track is already an existing source track. RETINFO ANTF0xxxx – Provides IBM description for error condition. ANTRQST function-call – Internal API request has failed. Return Code and Reason Code are displayed. EXCP FAILED – I/O command has issued an error return code. IOB Sense information is displayed for diagnostic purposes NORMAL I/O PERFORMED – FLASH operation is not allowed due to reason displayed in IOB Sense information. Copy / Move is performed using Normal I/O. Message is informational. tracedata – Debugging and diagnostic trace information is displayed during error handling or if “debugging” is enabled. FDR150 DISK TRACK X'cccchhhh' BYPASSED ERROR WHEN DUMPED Reason: FDR detected an I/O error or logical error when this track was dumped. Another message may have been issued detailing the error. Since the data was not properly dumped, FDR does not restore the track on the restore function. Action: The data set associated with this track may be incomplete. On a data set restore, message FDR155 indicates the dsname. If message FDR155 does not appear, the track was not needed for this restore. If you need assistance, contact INNOVATION DATA PROCESSING. CHAPTER 100 – PAGE 100-29 –
Page 1 and 2: MESSAGES AND CODES INTRODUCTION TO
Page 3 and 4: MESSAGES AND CODES FDR CONSOLE MESS
Page 17 and 18: MESSAGES AND CODES MESSAGES FROM FD
Page 19 and 20: FDR020 Reason: Action: MESSAGES AND
Page 27: MESSAGES AND CODES CHAPTER 100 - PA
Page 59 and 60: MESSAGES AND CODES CHAPTER 100 - PA
Page 79 and 80:
MESSAGES AND CODES MESSAGES FROM FD
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
MESSAGES AND CODES CHAPTER 100 - PA
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
FDR547 Reason: Action: MESSAGES AND
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
FDR939 Reason: MESSAGES AND CODES T
Page 123 and 124:
MESSAGES AND CODES MESSAGES FROM SA
Page 125 and 126:
100.6 COMPAKTOR MESSAGES (CPKNNNXX)
Page 127 and 128:
CHAPTER 100 - PAGE 100-127 - MESSAG
Page 129 and 130:
MESSAGES AND CODES COMPAKTOR MESSAG
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
CPK526E MESSAGES AND CODES COMPAKTO
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
MESSAGES AND CODES FDRREORG MESSAGE
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
MESSAGES AND CODES ABEND CODES 100.
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
100.9 WAIT STATE CODES FROM SAR WAI
show all

FDR V54L78 - Innovation Data Processing

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?