FDR V54L78 - Innovation Data Processing

MESSAGES AND CODES
MESSAGES FROM FDR, DSF, AND ABR (FDRNNN) 100.3
FDR326 function ENDED WITH NO dsvol process
Reason: DSF, FDRCOPY, or ABR was not able to successfully process any of the data sets or
volumes specified; or, no SELECT Commands followed a RESTORE, COPY, or
MOVE command.
“function” is RESTORE, COPY, MOVE, or REORG.
“dsvol” is VOLUMES or DATA SETS.
“process” is RESTORED, COPIED, MOVED SELECTED, or REORGED.
Action: Correct any specification errors and resubmit. If you wanted to select a VSAM cluster,
make sure you specified the VSAM cluster name and not the component names.
FDR327 CATALOG FAILURE TO LOCATE TAPE DSNAME=dsname
Reason: A restore from ABR Volume Backups was requested (RESTORE TYPE=ABR). The
required backup file was not found in the ABR catalog. If restoring an older backup
with the OLDB=nn operand, it may be that the backup generation and cycle selected
has been uncataloged by ABR, or expired by your tape management system.
Action: If the required backup tape is still available (has not been overwritten), even though it is
not cataloged, restores can still be done from it using the TAPEDD=n operand, and
providing a TAPEn DD statement specifying the ABR backup data set name, volume
serials, and file number (LABEL=n). This information can be found in the FDR305
messages printed during the backup, or from other ABR reports.
FDR328 UNABLE TO RESTORE REASON=reason--VOL=vvvvvv NVOL=vvvvvv
Reason: ABR was unable to perform a full volume restore (RESTORE TYPE=FDR). “vvvvvv” is
the original volume serial of the input volume and “nnnnnn” is the current volume
serial of the output volume. “reason” is:
1 RESTORE VOL OR DISK(X) MISSING – ABR did not find a DISKxxxx DD
statement pointing to the disk volume to be restored to (the original volume,
VOL=, or the new volume, NVOL=). If the ONLINE parameter was specified
to dynamically allocate the output volume, this can mean that the output
volume was not online; this also applies to FDRDRP.
2 NO ABR MODEL OR NO BACKUPS – GEN= was omitted, but either the
original volume was not online or an error occurred reading the ABR Model
DSCB from the volume AND no backups were cataloged for this volume in the
ABR catalog. So, ABR cannot find backups for this volume. At a disaster site,
be sure that the ABR catalog has been restored to its latest version.
3 TAPEDD NOT MATCHING A TAPEX DD – The TAPEDD=x operand was
specified. ABR could not find a TAPEx DD statement with the same
character as specified in this operand.
4 GEN SPECIFIED WITHOUT CYCLE –
5 GEN=CUR - NO BACKUPS CATALOGED – GEN=CURRENT was
specified but either no backup entries for this volume found on the ABR
catalog or an I/O error occurred reading the catalog.
6 SMS TO NON-SMS OR VICE-VERSA – A backup of an SMS volume is
being restored to a non-SMS volume, or a backup of a non-SMS volume is
being restored to an SMS volume. If “OVERRIDDEN” is displayed, then an SMS
backup is being restored to a non-SMS volume using SMSPROT=NONE.
7 FDRDRP DISASTER TRIAL HAS EXPIRED – Your trial of FDRDRP has
expired. Contact INNOVATION DATA PROCESSING if you want to extend
your trial or license FDRDRP.
8 INSUFFICIENT STORAGE SPECIFIED – A GETMAIN for a required work
area failed. On ESA and z/OS systems, the work area is above the 16M
line. Increase the size of your above the line private area with
REGION=nnM on the EXEC JCL statement.
CHAPTER 100 – PAGE 100-69 –