FDR V54L78 - Innovation Data Processing

MESSAGES AND CODES
MESSAGES FROM FDR, DSF, AND ABR (FDRNNN) 100.3
FDR211 FDR ERROR ON DD=ddname REASON=reason
Reason: FDRINSTANT discovered an error when attempting to initialize “ddname”. The “reason” can be:
8 FDR.USE.UNIT NOT FOUND – The disk device specified by
DSN=FDR.USE.UNITuuuu on the DISKx DD statement was not found in
your I/O configuration.
9 FDR.USE.UNIT IS ONLINE – The disk device specified by
DSN=FDR.USE.UNITuuuu on the DISKx DD statement is online. It must be
offline to z/OS.
A FDRINSTANT VOLSER MISMATCH – The volume serial of the offline disk
device being dumped does not match the volume serial of the online
B
primary volume.
INSTANT TRIAL HAS EXPIRED – FDRINSTANT trial has expired. Contact
INNOVATION DATA PROCESSING for assistance.
C FDRINSTANT UNIT NOT FOUND – The disk device containing the
FDRINSTANT volume image was not found in your I/O configuration. For
PGM=FDR or FDRDSF, if you specify BCV=, PPRC=, FCOPY=, or SNAP=,
this can also occur if you are trying to do Instant backups and non-Instant
backups in the same step.
D FDR INSTANT PATH GROUP ERR – FDR called the IBM module
IECDVPTH to establish path groups for the offline disk, but the return code
was non-zero. The backup is completed but there may be some
performance degradation.
E
F
G
H
I
J
K
M
INSTANT BKUP NOT CATALOGED – The latest backup generation and
cycle as recorded in the ABR Model DSCB is not cataloged.
INSTANT BKUP ALREADY DONE – The latest backup generation and
cycle as recorded in the ABR Model DSCB is currently cataloged to a tape
or a disk other than the source disk itself, so the backup has already been
moved. This message is normal if you restart the ABR backup step after
some backups have been successfully moved to tape; it does not set any
error codes and processing on the volume is bypassed. Note that this
reason can occur if the previous SNAP, SPLIT, PSPLIT, or FCOPY step
failed on this volume, but that failure sets an error code.
INSTANT BKUP UNIT MISSING – A SNAP, SPLIT, PSPLIT, or FCOPY
was previously done, but FDR cannot locate the UCB for the device that
was the target of the operation (that contains the volume image).
INSTANT BKUP GEN/CYC ERROR – The generation/cycle of the backup
on the offline volume is not the same as current generation/cycle as
recorded in the ABR Model DSCB. This can also occur if an offline volume
is released in a prior unsuccessful run with FCOPY=(USE,REL) and the
DUMP job is being rerun.
LOAD FAILURE FOR MODULE EMCSAI/EMCQCAPI – FDR was unable
to load an EMC API module. The EMC libraries must be in the system
linklist or a STEPLIB in the FDR step.
INSTANTBKUP TYPE= MISMATCH – The TYPE= parameter used on the
SNAP, SPLIT, PSPLIT, or FCOPY operation was different from that
specified on the subsequent DUMP statement.
FDRINSTANT LABEL I/O ERROR – An I/O error occurred reading the
volume label from the offline volume.
INSTANTUNIT=uuuu NOT READY – The offline disk copy of the online
disk is not ready. If you have use the DSN=FDR.USE.UNITuuuu in the FDR
DISKx DD statement, this may mean that you have provided the wrong
offline device address, or it may mean that the offline copy has not been
properly split from its online source. If this is a BCV in an EMC subsystem or
a ShadowImage copy in a HDS subsystem, this may mean that the SPLIT
or PSPLIT function has not been executed or has not completed.
CHAPTER 100 – PAGE 100-46 –