FDR V54L78 - Innovation Data Processing

More documents

Recommendations

Info

MESSAGES AND CODES MESSAGES FROM FDR, DSF, AND ABR (FDRNNN) 100.3 FDR289 ERROR OBTAINING type DEFINITIONS R15=nnnnnnnn, SFN=fn, RETN=rrrrrrrr, RSN=ssssssss Reason: FDRCONVT was unable to obtain the definitions for SMS classes; type is STORCLAS, MGMTCLAS, or DATACLAS. R15 contains the return code from the SMS subsystem call. “fn” is the SMS function code. “rrrrrrrr” and “ssssssss” are the SMS return code and reason codes. The codes can be found in the IBM manual DFSMSdfp Diagnosis Reference. Action: Correct the error. Contact INNOVATION DATA PROCESSING for technical assistance if necessary. FDR290 type FACILITY CLASS NOT AUTHORIZED Reason: The authorization check for the specified RACF FACILITY class resource failed. “type” may be: Action: CONVERTVOL – The user was not authorized to resource STGADMIN.ADR.CONVERTV - required for FDRCONVT. INCAT – The INCAT parameter was specified but the user was not authorized to resource STGADMIN.ADR.CONVERTV.INCAT. BYPASSACS – The BYPASSACS parameter was specified but the user was not authorized to resource STGADMIN.ADR.RESTORE.BYPASSACS. Insure that the job has authority to the required RACF resources. FDR291 INCATNAME PARAMETER IGNORED -- CATLG=YES NOT SPECIFIED Reason: The INCAT parameter was specified without CATLG=YES when converting to SMS management. SMS-Managed data sets must be catalogued in the catalog where their high-level qualifier(s) is/are aliased. Action: Recatalog the data sets to the correct catalog or specify CATLG=YES and rerun the job. FDR292 INVALID DSN/DSG NAME Reason: The DSN or DSG parameter did not begin with an alphameric or national character. The special form of the DSN or DSG parameter beginning with a period is not allowed with FDRCONVT. Action: Revise the DSN or DSG parameter and rerun the job. FDR293 THRESHOLD PERCENT: LO=ll, HI=hh, PERCENT OF VOLUME IN USE=pp Reason: The high and low ALLOCATION/MIGRATION THRESHOLD values for the storage group to which this volume is assigned are displayed as well as the percentage of the disk volume that is in use. FDR294 FDRKWDPR INTERNAL ERROR Reason: An internal error was encountered while processing control statements. Action: Contact INNOVATION DATA PROCESSING for assistance. FDR295 INSUFFICIENT STORAGE Reason: Insufficient main storage was available for FDRCONVT to process all data sets on the volume. Action: Increase the region size and rerun the job. If there are a large number of VSAM components on the volume, increase the ICFCORE value. FDR296 WARNING: SPACE USED ON VOLUME EXCEEDS STORGRP THRESHOLD Reason: The percentage of the volume in use exceeds the upper value of the ALLOCATION/MIGRATION THRESHOLDS when converting to SMS management. The operating system may avoid allocating to this volume until the percentage of space used is decreased. Action: Move data sets off of the volume until the percentage of the volume in use is less than the THRESHOLD value. FDR297 UNKNOWN PARM: parm Reason: An unrecognized parameter was specified on a control statement. Action: Specify a valid parameter. CHAPTER 100 – PAGE 100-56 –
MESSAGES AND CODES MESSAGES FROM FDR, DSF, AND ABR (FDRNNN) 100.3 FDR298 REQUIRED PARM parmname MISSING Reason: A required parameter was not found on a control statement. Action: Supply the missing parameter. FDR299 VOLUME vvvvvv NOT FOUND Reason: Volume “vvvvvv” specified in the VOL= parameter was not mounted. Action: Specify the correct volume and rerun the job. FDR301 program/function -- VER v.r/mmt -- INNOVATION DATA PROCESSING DATE=yyyy.ddd PAGE nnn Reason: This is the ABR page heading. See message FDR001 for details. FDR302 Reason: CONTROL STATEMENT ERROR NEAR REL LOCATION nn -- REASON x -- JOB TERMINATED An error was encountered during the processing of a user-supplied control statement. If “NEAR REL LOCATION nn” appears, the keyword or operand causing the error is at or near column “nn” on the input statement. The error is defined by the reason code within the message. The failing statement is displayed immediately above. NOTE: The expression “SELECT statement” in the reason codes below refers to SELECT and EXCLUDE statements. For FDRABR, it also refers to MOUNT, PROFILE, PROTECT, and ALLOCATE statements. The reason “x” can be: 1 – A SELECT statement did not specify any operands. Control statement was blank after the command name. 2 – Command name on the first control statement was incorrectly specified. For example, FDRDSF must start with a DUMP, RESTORE, or PRINT statement. See the section in this manual for the program you are executing for details. 3 – Operand on the first control statement was incorrectly specified. (Valid operands are TYPE=DSF, RESERVE, etc.). 4 – Operand did not end with a blank or comma. 5 – SYSIN data set was empty. 6 – Expected continuation statement was not found. The previous statement ended with a comma and a blank. 7 – On the first control statement, invalid or incompatible operands were specified. (Examples: RESERVE was specified but TYPE= was omitted, or FROM/TO was specified and TYPE= followed it.) 7 – The TYPE= operand was omitted on a command that requires it (such as PRINT or COPY). 7 – A control statement after the first was not a SELECT statement. A SELECT statement contained an invalid keyword. (Valid keywords are DSN=, VOL=, etc.). 8 – An operand on a SELECT statement specified a blank or comma after the equal sign. 9 – On the control statement printed above, one of the options exceeded its maximum length. A data set name exceeded 44 characters. A volume serial number exceeded 6 characters. The TAPEDD= option exceeded one (1) character. The NOTIFY operand exceeded seven (7) characters. The DD= or NEWDD= operand exceeded eight (8) characters. B – C – D – E – The DD= or NEWDD= operand specified a DDname that did not appear in the JCL. Maximum number of SELECT statements was exceeded. The number of SELECT statements plus the number of commands in the PROTECT and/or ALLOCATE list was greater than the value specified in the MAXCARDS operand (default of 100 for ABR or 250 for FDRDSF). ADATE= operand did not specify numeric data. ADATE= operand is neither five digits (yyddd) nor seven digits (yyyyddd). CHAPTER 100 – PAGE 100-57 –
Page 1 and 2:
MESSAGES AND CODES INTRODUCTION TO
Page 3 and 4:
MESSAGES AND CODES FDR CONSOLE MESS
Page 5 and 6: MESSAGES AND CODES FDR CONSOLE MESS
Page 17 and 18: MESSAGES AND CODES MESSAGES FROM FD
Page 19 and 20: FDR020 Reason: Action: MESSAGES AND
Page 27 and 28: MESSAGES AND CODES CHAPTER 100 - PA
Page 55: MESSAGES AND CODES MESSAGES FROM FD
Page 107 and 108:
MESSAGES AND CODES MESSAGES FROM FD
Page 109 and 110:
Page 111 and 112:
FDR665 Reason: Action: MESSAGES AND
Page 113 and 114:
MESSAGES AND CODES CHAPTER 100 - PA
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
FDR939 Reason: MESSAGES AND CODES T
Page 123 and 124:
MESSAGES AND CODES MESSAGES FROM SA
Page 125 and 126:
100.6 COMPAKTOR MESSAGES (CPKNNNXX)
Page 127 and 128:
CHAPTER 100 - PAGE 100-127 - MESSAG
Page 129 and 130:
MESSAGES AND CODES COMPAKTOR MESSAG
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
CPK526E MESSAGES AND CODES COMPAKTO
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
MESSAGES AND CODES FDRREORG MESSAGE
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
MESSAGES AND CODES ABEND CODES 100.
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
100.9 WAIT STATE CODES FROM SAR WAI
show all

FDR V54L78 - Innovation Data Processing

Create successful ePaper yourself

Delete template?

Save as template?