FR-F700 INSTRUCTION MANUAL (BASIC) - MRO Stop

More documents

Recommendations

Info

Method of removal and reinstallation of thefront cover2.2 Method of removal and reinstallation of the front cover•Removal of the operation panel1) Loosen the two screws on the operation panel.(These screws cannot be removed.)2) Push the left and right hooks of the operation paneland pull the operation panel toward you to remove.When reinstalling the operation panel, insert it straight to reinstall securely and tighten the fixed screws of theoperation panel.FR-F720-30K or less, FR-F740-30K or less•Removal1) Loosen the installation screws of the 2) Pull the front cover toward you to remove by pushing anfront cover.installation hook using left fixed hooks as supports.Front coverFront cover2•Reinstallation1) Insert the two fixed hooks on the left side ofthe front cover into the sockets of theinverter.2) Using the fixed hooks as supports,securely press the front coveragainst the inverter.(Although installation can be donewith the operation panel mounted,make sure that a connector issecurely fixed.)Installation hook3) Tighten the installationscrews and fix the frontcover.INSTALLATION AND WIRINGFront coverFront coverFront cover5
Method of removal and reinstallation of thefront coverFR-F720-37K or more, FR-F740-37K or more•Removal1) Remove installation screws on 2) Loosen the installationthe front cover 1 to remove the screws of the front cover 2.front cover 1.3) Pull the front cover 2 toward you toremove by pushing an installationhook on the right side using leftfixed hooks as supports.Installation hookFront cover 1Front cover 2•Reinstallation1) Insert the two fixed hooks on the left side of thefront cover 2 into the sockets of the inverter.2) Using the fixed hooks as supports, securelypress the front cover 2 against the inverter.(Although installation can be done with theoperation panel mounted, make sure that aconnector is securely fixed.)Front cover 2 Front cover 23) Fix the front cover 2 with theinstallation screws.4) Fix the front cover 1 with theinstallation screws.Front cover 2Front cover 1REMARKS⋅ For the FR-F740-185K or more, the front cover 1 is separated into two parts.CAUTION1. Fully make sure that the front cover has been reinstalled securely. Always tighten the installation screws of the front cover.2. The same serial number is printed on the capacity plate of the front cover and the rating plate of the inverter. Before reinstalling thefront cover, check the serial numbers to ensure that the cover removed is reinstalled to the inverter from where it was removed.6
Page 1 and 2: INVERTERINSTRUCTION MANUAL (BASIC)F
Page 3 and 4: — CONTENTS —1 PRODUCT CHECKING
Page 5 and 6: 6 PRECAUTIONS FOR MAINTENANCE AND I
Page 7 and 8: 2 INSTALLATION AND WIRINGThree-phas
Page 9: Peripheral devices400V classMotorOu
Page 13 and 14: Wiring2.4 Wiring2.4.1 Terminal conn
Page 15 and 16: Wiring2.4.3 Specification of main c
Page 17 and 18: Wiring400V classFR-F740-0.75K to 5.
Page 19 and 20: Wiring(1) Cable sizes etc., of the
Page 21 and 22: Wiring(2) Notes on earthing (ground
Page 23 and 24: UVWWiring• FR-F720-15K, FR-F740-1
Page 25 and 26: WiringTypeFrequency settingTerminal
Page 27 and 28: Wiring2.4.6 Changing the control lo
Page 29 and 30: Wiring2.4.7 Wiring of control circu
Page 31 and 32: Wiring2.4.9 RS-485 terminal block
Page 33 and 34: Precautions for use of the inverter
Page 35 and 36: Failsafe of the system which uses t
Page 37 and 38: Operation panel (FR-DU07)3.2 Operat
Page 39 and 40: Operation panel (FR-DU07)3.2.3 Oper
Page 41 and 42: Operation panel (FR-DU07)3.2.7 Chan
Page 43 and 44: When the rated motor frequency is 5
Page 45 and 46: Start/stop from the operation panel
Page 53 and 54: Make a start and stop with terminal
Page 61 and 62:
Increase the starting torque (Pr. 0
Page 63 and 64:
Change acceleration and deceleratio
Page 65 and 66:
Energy saving operation (Pr. 60)Ope
Page 67 and 68:
Parameter clear, all parameter clea
Page 69 and 70:
Parameter copy and parameter verifi
Page 71 and 72:
Parameter listOperation selection a
Page 73 and 74:
Parameter list4.9.3 Parameter list
Page 75 and 76:
Parameter listFunctionJog operation
Page 77 and 78:
Parameter listFunctionDetection of
Page 79 and 80:
Parameter listFunctionRetry functio
Page 81 and 82:
Parameter listFunctionOperation mod
Page 83 and 84:
Parameter listFunctionChange of ana
Page 85 and 86:
Parameter listSwitch between the in
Page 87 and 88:
Parameter listFunctionOperation sel
Page 89 and 90:
Parameter listFunctionSlip compensa
Page 91 and 92:
Parameter listFunctionPU connector
Page 93 and 94:
Parameter listFunctionRegeneration
Page 95 and 96:
Parameter listFunctionAdjustment of
Page 97 and 98:
List of faults or alarm display5.2
Page 99 and 100:
Causes and corrective actionsOperat
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Correspondences between digital and
Page 111 and 112:
Check and clear of the faults histo
Page 113 and 114:
Check first when you have troubles5
Page 115 and 116:
Inspection item6 PRECAUTIONS FOR MA
Page 117 and 118:
Inspection item6.1.4 Display of the
Page 119 and 120:
Inspection item(1) Cooling fanThe r
Page 121 and 122:
Inspection item• Removal (FR-F740
Page 123 and 124:
Rating7 SPECIFICATIONS7.1 Rating•
Page 125 and 126:
Common specifications7.2 Common spe
Page 127 and 128:
Outline dimension drawings7.3 Outli
Page 129 and 130:
Outline dimension drawings• FR-F7
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Outline dimension drawings• Opera
Page 139 and 140:
Heatsink protrusion attachment proc
Page 141 and 142:
For customers who have replaced the
Page 143 and 144:
Appendix 2 Instructions for UL and
Page 145 and 146:
Appendix 3 Instructions for Complia
Page 147:
REVISIONS*The manual number is give
show all

FR-F700 INSTRUCTION MANUAL (BASIC) - MRO Stop

Create successful ePaper yourself

Delete template?

Save as template?