FR-F700 INSTRUCTION MANUAL (BASIC) - MRO Stop

More documents

Recommendations

Info

Heatsink protrusion attachment procedure(3) Installation of the inverterPush the inverter heatsink portion outside the enclosure and fix the enclosure and inverter with upper and lowerinstallation frame.InverterInside theenclosureEnclosureExhausted air** For the FR-F740-250K or more, there are fingerguards behind the enclosure. Therefore, thethickness of the panel should be less than10mm(*1) and also do not place anything aroundfinger guards to avoid contact with the fingerguards.EnclosureInstallationframe10* 1 140Finger guard(Unit: mm)Dimension ofCoolingwind the outside ofD1 the enclosureInverter TypeD1(mm)FR-F740-185K, 220K 185FR-F740-250K to 560K 184CAUTION· Having a cooling fan, the cooling section which comes out of the enclosure can not be used in the environment of waterdrops, oil, mist, dust, etc.· Be careful not to drop screws, dust etc. into the inverter and cooling fan section.SPECIFICATIONS61357
For customers who have replaced the older model with this inverterAPPENDICESAppendix 1 For customers who have replaced the older model with thisinverterAppendix 1-1(1) Instructions for installationReplacement of the FR-F500 series1)Removal procedure of the front cover was changed. (with screws) Please note. (Refer to page 5.)2)Removal procedure of the operation panel was changed. (with screws) Please note. (Refer to page 5.)3)Plug-in options of the F500 series are not compatible4)Operation panel (FR-DU04) can not be used.5)Setup software (FR-SW0-SETUP) can not be used.(2) Wiring instructions1)The control circuit terminal block can be used for the FR-F700 series without removing wiring.Note that the wiring cover (0.75K to 30K) is not compatible.FR-F500 seriesFR-F700 series(Note that the relay output 2 (A2, B2, C2) specific for the FR-F700 series can not be used with the FR-F500 seriesterminals.)(3) Instructions for continuous use of the FR-PU04 (parameter unit)1)For the FR-F700 series, many functions (parameters) have been added. When setting these parameters, theparameter name and setting range are not displayed. Parameter list, change list, initial value list, initial value list2 and parameter clear of the HELP function can not be used.2)For the FR-F700 series, many protective functions have been added. These functions activate, but all faults aredisplayed as "Fault 14". When the faults history has been checked, "E.14" appears. Added faults display will notappear on the parameter unit.3) User initial value setting can not be used.4) User registration/clear (user group 2) can not be used.5) Parameter copy/verification function can not be used.136
Page 1 and 2:
INVERTERINSTRUCTION MANUAL (BASIC)F
Page 3 and 4:
— CONTENTS —1 PRODUCT CHECKING
Page 5 and 6:
6 PRECAUTIONS FOR MAINTENANCE AND I
Page 7 and 8:
2 INSTALLATION AND WIRINGThree-phas
Page 9 and 10:
Peripheral devices400V classMotorOu
Page 11 and 12:
Method of removal and reinstallatio
Page 13 and 14:
Wiring2.4 Wiring2.4.1 Terminal conn
Page 15 and 16:
Wiring2.4.3 Specification of main c
Page 17 and 18:
Wiring400V classFR-F740-0.75K to 5.
Page 19 and 20:
Wiring(1) Cable sizes etc., of the
Page 21 and 22:
Wiring(2) Notes on earthing (ground
Page 23 and 24:
UVWWiring• FR-F720-15K, FR-F740-1
Page 25 and 26:
WiringTypeFrequency settingTerminal
Page 27 and 28:
Wiring2.4.6 Changing the control lo
Page 29 and 30:
Wiring2.4.7 Wiring of control circu
Page 31 and 32:
Wiring2.4.9 RS-485 terminal block
Page 33 and 34:
Precautions for use of the inverter
Page 35 and 36:
Failsafe of the system which uses t
Page 37 and 38:
Operation panel (FR-DU07)3.2 Operat
Page 39 and 40:
Operation panel (FR-DU07)3.2.3 Oper
Page 41 and 42:
Operation panel (FR-DU07)3.2.7 Chan
Page 43 and 44:
When the rated motor frequency is 5
Page 45 and 46:
Start/stop from the operation panel
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Make a start and stop with terminal
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Increase the starting torque (Pr. 0
Page 63 and 64:
Change acceleration and deceleratio
Page 65 and 66:
Energy saving operation (Pr. 60)Ope
Page 67 and 68:
Parameter clear, all parameter clea
Page 69 and 70:
Parameter copy and parameter verifi
Page 71 and 72:
Parameter listOperation selection a
Page 73 and 74:
Parameter list4.9.3 Parameter list
Page 75 and 76:
Parameter listFunctionJog operation
Page 77 and 78:
Parameter listFunctionDetection of
Page 79 and 80:
Parameter listFunctionRetry functio
Page 81 and 82:
Parameter listFunctionOperation mod
Page 83 and 84:
Parameter listFunctionChange of ana
Page 85 and 86:
Parameter listSwitch between the in
Page 87 and 88:
Parameter listFunctionOperation sel
Page 89 and 90: Parameter listFunctionSlip compensa
Page 91 and 92: Parameter listFunctionPU connector
Page 93 and 94: Parameter listFunctionRegeneration
Page 95 and 96: Parameter listFunctionAdjustment of
Page 97 and 98: List of faults or alarm display5.2
Page 99 and 100: Causes and corrective actionsOperat
Page 109 and 110: Correspondences between digital and
Page 111 and 112: Check and clear of the faults histo
Page 113 and 114: Check first when you have troubles5
Page 115 and 116: Inspection item6 PRECAUTIONS FOR MA
Page 117 and 118: Inspection item6.1.4 Display of the
Page 119 and 120: Inspection item(1) Cooling fanThe r
Page 121 and 122: Inspection item• Removal (FR-F740
Page 123 and 124: Rating7 SPECIFICATIONS7.1 Rating•
Page 125 and 126: Common specifications7.2 Common spe
Page 127 and 128: Outline dimension drawings7.3 Outli
Page 129 and 130: Outline dimension drawings• FR-F7
Page 137 and 138: Outline dimension drawings• Opera
Page 139: Heatsink protrusion attachment proc
Page 143 and 144: Appendix 2 Instructions for UL and
Page 145 and 146: Appendix 3 Instructions for Complia
Page 147: REVISIONS*The manual number is give
show all

FR-F700 INSTRUCTION MANUAL (BASIC) - MRO Stop

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?