FR-F700 INSTRUCTION MANUAL (BASIC) - MRO Stop

More documents

Recommendations

Info

3DRIVE THE MOTORStart/stop from the operation panel (PUoperation mode)3.5 Start/stop from the operation panel (PU operation mode)POINTFrom where is the frequency command given?· Operation at the frequency set in the frequency setting modeof the operation panel →Refer to 3.5.1 (Refer to page 39)· Operation using the setting dial as the potentiometer→Refer to 3.5.2 (Refer to page 40)· Change of frequency with ON/OFF switches connected toterminals →Refer to 3.5.3 (Refer to page 41)· Frequency setting with a voltage input signal→Refer to 3.5.4 (Refer to page 43)· Frequency setting with a current input signal→Refer to 3.5.5 (Refer to page 45)[Connection diagram]Three-phaseAC power supplyInverterR/L1S/L2T/L3<strong>FR</strong>-DU073.5.1 Set the set frequency to operate (example: performing operation at 30Hz)Operation1.Screen at powering onThe monitor display appears.Display,,UVWMotor2.Press to choose the PUoperation mode.3.Turn to show the frequencyyou want to set.The frequency flickers for about 5s.4.While the value is flickering,press to set the frequency.If you do not press , the value flickers for about 5sand the display then returns to " " (monitor display) Hz.At this time, return to "Step 3" and set the frequency again.5.After the value flickered for about 3s,the display returns to " " (monitor display).Press (or ) to start operation.6.To change the set frequency, perform theoperation in above steps 3 and 4.(Starts from the previously set frequency.)( )PU indication is lit.Flickers forabout 5sFlicker ··· Frequency setting complete!!3s later7.Pressto stop.Operation cannot be performed at the set frequency ... Why?Did you carry out step 4 within 5s after step 3? (Did you press within 5s after turning ?)The frequency does not change by turning ... Why?Check to see if the operation mode selected is the external operation mode. (Press to change tothe PU operation mode.)Operation does not change to the PU operation mode ... Why?Check that "0" (initial value) is set in Pr. 79 Operation mode selection.Check that the start command is not on.Change acceleration time Pr. 7 (Refer to page 58)Change deceleration time Pr. 8 (Refer to page 58)For example, limit the motor speed to 60Hz maximum. Set "60Hz" in Pr. 1. (Refer to page 57)REMARKS· Press to show the set frequency.· can also be used like a potentiometer to perform operation. (Refer to page 40)39
Start/stop from the operation panel (PUoperation mode)3.5.2 Use the setting dial like a potentiometer to perform operation.POINTSet "0" (extended mode parameter valid) in Pr. 160 User group read selection.Set "1" (setting dial potentiometer mode) in Pr. 161 Frequency setting/key lock operation selection.Operation exampleChange the frequency from 0Hz to 60Hz during operationOperationDisplay1. Screen at powering onThe monitor display appears.2. Press to choose the PU operationmode.PU indication is lit.3. Press to choose the parametersetting mode.The parameter numberpreviously read appears.4. Turn until (Pr. 160) appears.5. Press to read the currently set value." " (initial value) appears.6. Turn to change it tothe setting value of " ".7. Press to set.Flicker ··· Parameter setting complete!!8. Change Pr. 161 to the setting value of " "in the similar manner. (Refer to step 4 to 7.)9. Mode/monitor checkPress twice to choosemonitor/frequency monitor.Flicker ··· Parameter setting complete!!10. Press (or ) to start the inverter.11. Turn until " " appears.The flickering frequency is the set frequency.You need not press .The frequency flickers for about 5s.REMARKS· If flickering "60.00" turns to "0.0", the Pr. 161 Frequency setting/key lock operation selection setting may not be "1".· Independently of whether the inverter is running or at a stop, the frequency can be set by merely turning .40
Page 1 and 2: INVERTERINSTRUCTION MANUAL (BASIC)F
Page 3 and 4: — CONTENTS —1 PRODUCT CHECKING
Page 5 and 6: 6 PRECAUTIONS FOR MAINTENANCE AND I
Page 7 and 8: 2 INSTALLATION AND WIRINGThree-phas
Page 9 and 10: Peripheral devices400V classMotorOu
Page 11 and 12: Method of removal and reinstallatio
Page 13 and 14: Wiring2.4 Wiring2.4.1 Terminal conn
Page 15 and 16: Wiring2.4.3 Specification of main c
Page 17 and 18: Wiring400V classFR-F740-0.75K to 5.
Page 19 and 20: Wiring(1) Cable sizes etc., of the
Page 21 and 22: Wiring(2) Notes on earthing (ground
Page 23 and 24: UVWWiring• FR-F720-15K, FR-F740-1
Page 25 and 26: WiringTypeFrequency settingTerminal
Page 27 and 28: Wiring2.4.6 Changing the control lo
Page 29 and 30: Wiring2.4.7 Wiring of control circu
Page 31 and 32: Wiring2.4.9 RS-485 terminal block
Page 33 and 34: Precautions for use of the inverter
Page 35 and 36: Failsafe of the system which uses t
Page 37 and 38: Operation panel (FR-DU07)3.2 Operat
Page 39 and 40: Operation panel (FR-DU07)3.2.3 Oper
Page 41 and 42: Operation panel (FR-DU07)3.2.7 Chan
Page 43: When the rated motor frequency is 5
Page 47 and 48: Start/stop from the operation panel
Page 53 and 54: Make a start and stop with terminal
Page 61 and 62: Increase the starting torque (Pr. 0
Page 63 and 64: Change acceleration and deceleratio
Page 65 and 66: Energy saving operation (Pr. 60)Ope
Page 67 and 68: Parameter clear, all parameter clea
Page 69 and 70: Parameter copy and parameter verifi
Page 71 and 72: Parameter listOperation selection a
Page 73 and 74: Parameter list4.9.3 Parameter list
Page 75 and 76: Parameter listFunctionJog operation
Page 77 and 78: Parameter listFunctionDetection of
Page 79 and 80: Parameter listFunctionRetry functio
Page 81 and 82: Parameter listFunctionOperation mod
Page 83 and 84: Parameter listFunctionChange of ana
Page 85 and 86: Parameter listSwitch between the in
Page 87 and 88: Parameter listFunctionOperation sel
Page 89 and 90: Parameter listFunctionSlip compensa
Page 91 and 92: Parameter listFunctionPU connector
Page 93 and 94: Parameter listFunctionRegeneration
Page 95 and 96:
Parameter listFunctionAdjustment of
Page 97 and 98:
List of faults or alarm display5.2
Page 99 and 100:
Causes and corrective actionsOperat
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Correspondences between digital and
Page 111 and 112:
Check and clear of the faults histo
Page 113 and 114:
Check first when you have troubles5
Page 115 and 116:
Inspection item6 PRECAUTIONS FOR MA
Page 117 and 118:
Inspection item6.1.4 Display of the
Page 119 and 120:
Inspection item(1) Cooling fanThe r
Page 121 and 122:
Inspection item• Removal (FR-F740
Page 123 and 124:
Rating7 SPECIFICATIONS7.1 Rating•
Page 125 and 126:
Common specifications7.2 Common spe
Page 127 and 128:
Outline dimension drawings7.3 Outli
Page 129 and 130:
Outline dimension drawings• FR-F7
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Outline dimension drawings• Opera
Page 139 and 140:
Heatsink protrusion attachment proc
Page 141 and 142:
For customers who have replaced the
Page 143 and 144:
Appendix 2 Instructions for UL and
Page 145 and 146:
Appendix 3 Instructions for Complia
Page 147:
REVISIONS*The manual number is give
show all

FR-F700 INSTRUCTION MANUAL (BASIC) - MRO Stop

Create successful ePaper yourself

Delete template?

Save as template?