FR-F700 INSTRUCTION MANUAL (BASIC) - MRO Stop

More documents

Recommendations

Info

7.4 Heatsink protrusion attachment procedureHeatsink protrusion attachment procedureWhen encasing the inverter in an enclosure, the generated heat amount in an enclosure can be greatly reduced byinstalling the heatsink portion of the inverter outside the enclosure. When installing the inverter in a compactenclosure, etc., this installation method is recommended.7.4.1 When using a heatsink protrusion attachment (FR-A7CN)For the FR-F720-2.2K to 110K, FR-F740-0.75K to 160K, a heatsink can be protruded outside the enclosure using aheatsink protrusion attachment (FR-A7CN). For a panel cut dimension drawing and an installation procedure of theheatsink protrusion attachment (FR-A7CN) to the inverter, refer to a manual of "heatsink protrusion attachment (FR-A7CN01 to 11)".7.4.2 Protrusion of heatsink of the FR-F740-185K or more(1) Panel cuttingCut the panel of the enclosure according to the inverter capacity.• FR-F740-185K, 220K• FR-F740-250K, 280K, 315K13484200 2006-M10 screw15662300 3006-M10 screw985954Hole984954Hole18• FR-F740-355K, 400K(Unit: mm)15• FR-F740-450K, 500K, 560K(Unit: mm)7716-M10 screw9768-M10 screw315 31521300 300 3001300125821Hole15501508Hole21(Unit: mm)21(Unit: mm)SPECIFICATIONS1337
Heatsink protrusion attachment procedure(2) Shift and removal of a rear side installation frame• FR-F740-250K to 315KOne installation frame is attached to each of the upper and lowerpart of the inverter. Change the position of the rear side installationframe on the upper and lower side of the inverter to the frontside as shown on the right. When changing the installationframes, make sure that the installation orientation is correct.ShiftUpperinstallationframe• FR-F740-185K/220K, 355K or moreTwo installation frames each are attached to the upper and lowerparts of the inverter. Remove the rear side installation frame onthe upper and lower side of the inverter as shown on the right.ShiftLowerinstallationframeRemovalUpper installationframe (rear side)Lower installationframe (rear side)Removal134
Page 1 and 2:
INVERTERINSTRUCTION MANUAL (BASIC)F
Page 3 and 4:
— CONTENTS —1 PRODUCT CHECKING
Page 5 and 6:
6 PRECAUTIONS FOR MAINTENANCE AND I
Page 7 and 8:
2 INSTALLATION AND WIRINGThree-phas
Page 9 and 10:
Peripheral devices400V classMotorOu
Page 11 and 12:
Method of removal and reinstallatio
Page 13 and 14:
Wiring2.4 Wiring2.4.1 Terminal conn
Page 15 and 16:
Wiring2.4.3 Specification of main c
Page 17 and 18:
Wiring400V classFR-F740-0.75K to 5.
Page 19 and 20:
Wiring(1) Cable sizes etc., of the
Page 21 and 22:
Wiring(2) Notes on earthing (ground
Page 23 and 24:
UVWWiring• FR-F720-15K, FR-F740-1
Page 25 and 26:
WiringTypeFrequency settingTerminal
Page 27 and 28:
Wiring2.4.6 Changing the control lo
Page 29 and 30:
Wiring2.4.7 Wiring of control circu
Page 31 and 32:
Wiring2.4.9 RS-485 terminal block
Page 33 and 34:
Precautions for use of the inverter
Page 35 and 36:
Failsafe of the system which uses t
Page 37 and 38:
Operation panel (FR-DU07)3.2 Operat
Page 39 and 40:
Operation panel (FR-DU07)3.2.3 Oper
Page 41 and 42:
Operation panel (FR-DU07)3.2.7 Chan
Page 43 and 44:
When the rated motor frequency is 5
Page 45 and 46:
Start/stop from the operation panel
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Make a start and stop with terminal
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Increase the starting torque (Pr. 0
Page 63 and 64:
Change acceleration and deceleratio
Page 65 and 66:
Energy saving operation (Pr. 60)Ope
Page 67 and 68:
Parameter clear, all parameter clea
Page 69 and 70:
Parameter copy and parameter verifi
Page 71 and 72:
Parameter listOperation selection a
Page 73 and 74:
Parameter list4.9.3 Parameter list
Page 75 and 76:
Parameter listFunctionJog operation
Page 77 and 78:
Parameter listFunctionDetection of
Page 79 and 80:
Parameter listFunctionRetry functio
Page 81 and 82:
Parameter listFunctionOperation mod
Page 83 and 84:
Parameter listFunctionChange of ana
Page 85 and 86:
Parameter listSwitch between the in
Page 87 and 88: Parameter listFunctionOperation sel
Page 89 and 90: Parameter listFunctionSlip compensa
Page 91 and 92: Parameter listFunctionPU connector
Page 93 and 94: Parameter listFunctionRegeneration
Page 95 and 96: Parameter listFunctionAdjustment of
Page 97 and 98: List of faults or alarm display5.2
Page 99 and 100: Causes and corrective actionsOperat
Page 109 and 110: Correspondences between digital and
Page 111 and 112: Check and clear of the faults histo
Page 113 and 114: Check first when you have troubles5
Page 115 and 116: Inspection item6 PRECAUTIONS FOR MA
Page 117 and 118: Inspection item6.1.4 Display of the
Page 119 and 120: Inspection item(1) Cooling fanThe r
Page 121 and 122: Inspection item• Removal (FR-F740
Page 123 and 124: Rating7 SPECIFICATIONS7.1 Rating•
Page 125 and 126: Common specifications7.2 Common spe
Page 127 and 128: Outline dimension drawings7.3 Outli
Page 129 and 130: Outline dimension drawings• FR-F7
Page 137: Outline dimension drawings• Opera
Page 141 and 142: For customers who have replaced the
Page 143 and 144: Appendix 2 Instructions for UL and
Page 145 and 146: Appendix 3 Instructions for Complia
Page 147: REVISIONS*The manual number is give
show all

FR-F700 INSTRUCTION MANUAL (BASIC) - MRO Stop

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?