4 Introduction to the Plug-In Modules for the <strong>34980A</strong> Electrical Operating Conditions WARNING Transients The 34921A, 34922A, 34923A, 34924A, 34925A, 34931A, 34932A, 34933A, 34934A, 34937A, 34938A and 34939A modules are designed to safely withstand occasional transient overvoltages up to 1000 Vpeak. Typically, these transient overvoltages result from switching inductive loads or from nearby lightning strikes. The lightning- caused transient overvoltages that may occasionally occur on mains power outlets may be as high as 2500 Vpeak. The 34941A, 34942A, 34945A, 34946A, 34947A, 34950A, 34951A, 34952A and 34959A modules are intended for only low- voltage applications, and should not be connected to circuits that may generate or conduct large transient voltages. WARNING High Energy Sources To avoid electric shock, turn off the <strong>34980A</strong> and disconnect or de-energize all field wiring to the modules and the Analog Bus connector before removing any module or slot cover. These modules are designed to handle inputs up to their rated currents or their rated powers, whichever is less. Under certain fault conditions, high energy sources could provide substantially more current or power than a module can handle. It is important to provide external current limiting, such as fuses, if the module inputs are connected to high- energy sources. CAUTION Do not connect any of the modules directly to a mains power outlet. If it is necessary to measure a mains voltage or any circuit where a large inductive load may be switched, you must add signal conditioning elements to reduce the potential transients before they reach the module or the Analog Buses. Install current limiting devices between high energy sources and the module inputs. 170 <strong>Agilent</strong> <strong>34980A</strong> Mainframe User’s Guide
Symbols *RST state, 158 ±9.9E+37 (overload), 86 Numerics 10BaseT/100Base Tx, 23 2-wire versus 1-wire mode, 95 34832A BenchLink Data Logger Pro software, 3 34921A 40-Channel Armature Multiplexer Module, 165 34922A 70-Channel Armature Multiplexer Module, 165 34923A 40/80 Channel Reed Multiplexer Module, 165 34924A 70-Channel Reed Multiplexer Module, 165 34925A 40-Channel Optically Isolated FET Multiplexer Module, 165 34931A Dual 4x8 Armature Matrix Module, 165 34932A Dual 4x16 Armature Matrix Module, 165 34933A Dual/Quad 4x8 Reed Martix Module, 165 34934A High Density Matrix Module, 165 34937A 28-Channel Form C and 4-Channel Form A <strong>Switch</strong> Module, 165 34938A 28-channel, 5 Amp Form A <strong>Switch</strong> Module, 165 34939A 64-channel, 1 Amp Form A <strong>Switch</strong> Module, 165 34941A Quad 1x4, 50 Ohm, 3GHz RF Multiplexer Module, 165 34942A Quad 1x4, 75 Ohm, 1.5 GHz RF Multiplexer Module, 165 34945A Microwave <strong>Switch</strong> Attenuator/Driver Module, 165 34946A Dual 1x2 SPDT Terminated Microwave <strong>Switch</strong> Module, 165 34947A Triple 1x2 SPDT Unterminated Microwave <strong>Switch</strong> Module, 165 34950A 64-Bit Digital I/O Module with Memory and Counter, 165 34951A 4-Channel Isolated D/A Converter with Waveform Memory, 165 34952A <strong>Multifunction</strong> Module with 32-Bit Digital I/O, 2-Channel D/A and Totalizer, 165 34959A Breadboard Module, 165 <strong>34980A</strong> documentation, 61 simplified block diagram, 5 4W channel pairing, 103 5063-9214 Standard Rack Mount Kit, 32 A A/D conversion, 12 abort measurements, 82 absolute reading format, 123 ABus connector, 23, 24, 84 ac current measurements, 104 low frequency filter, 102 ac low frequency filter, 102 ac voltage measurements, 101 low frequency filter, 102 actuator switches, 20 addressing channel, 166 slots, 166 Advanced key, 36 <strong>Agilent</strong> Connectivity Guide, 45, 68 <strong>Agilent</strong> IO Libraries Suite, 45, 68 <strong>Agilent</strong> VEE, 53 Alarm key, 36 alarm limits, 7 alarm queue, 132 alarms, 132 Alarm Output connector, 136 annunciators, 134 latch mode, 136 output polarity, 137 rules, 132 scanning on alarm, 114 track mode, 136 viewing stored data, 135 with digital modules, 138 Alarms connector, 23, 24, 136 allow full control mode, 56 analog bus connector, 23, 24, 84 annunciators, 25 alarms, 134 arrow keys, 22 auto-IP address, 72 automatic channel delay, 121 automatic trigger delay, 91 autorange, 86 autorange thresholds, 86 autozero, 89 available documents, 61 B browser web control page, 55 buttons front panel, 22 C cables, 167 calendar, time and date, 153 calibration, 155 count, 156 default code, 155 message, 157 securing instrument, 155 Index security, 155 unsecuring instrument, 155 Cancel key, 22 celsius, 96 Chan Advance connector, 24 Chan Closed connector, 23, 24 channel advance, 129 channel closed, 129 channel configuration, 58 channel delay, 120 automatic delay, 121 Channel key (Configure menu), 36 Channel key (<strong>Measure</strong> group), 39 channel labels, 93 channel numbering, 166 channel pairing (4W), 103 channel relays front panel operation, 38 remote operation, 57 channel selection, 38 channels configuring for measurments, 42 clearing memory, 78 clock, 153 command errors. See <strong>34980A</strong> Programmer’s Reference Help file Command History field, 60 communication via GPIB, 51 via isolated LAN, 49 via site LAN, 47 computer connection, 45 condensation, 168 Configure key group, 22, 36 connecting to your PC, 45 connection via USB, 52 connectivity software, 45, 68 connector Alarms, 23, 136 analog bus, 23, 84 Chan Advance, 23 Chan Closed, 23 Ext Trig, 23, 116 GPIB (IEEE 488.2), 23 LAN, 23 USB, 23 VM Complete, 23 connector pinouts, 24 Control keys, 22 control output, 18 cooling requirements, 168 current measurements, 104 ac filter, 104 custom channel labels, 93 cycle count, 153, 154 <strong>Agilent</strong> <strong>34980A</strong> Mainframe User’s Guide 171 D DAC output, 19 data acquisition overview, 2 data acuisition circuitry overview, 5 data logger software, 3