Agilent 34980A  Multifunction Switch/Measure Unit 34980-90005

More documents

Recommendations

Info

3 Features and Functions Auto-IP The Auto- IP standard automatically assigns an IP address to the 34980A when on a network that does not have DHCP servers. If you change the Auto- IP configuration, you must cycle power on the 34980A to activate the new setting. Auto- IP allocates IP addresses from the link- local address range (169.254.xxx.xxx). From the factory, the Auto- IP setting is enabled. The Auto- IP setting is stored in non- volatile memory, and does not change when power has been off, after a Factory Reset (*RST command), or after an Instrument Preset (SYSTem:PRESet command). Front Panel Operation: Utility > REMOTE I/O > LAN > LAN SETTINGS > MODIFY > DHCP OFF > AUTO IP Remote Interface Operation: SYSTem:COMMunicate:LAN:AUTOip (OFF|ON} 72 Agilent 34980A Mainframe User’s Guide
Subnet Mask Features and Functions 3 The instrument uses the Subnet Mask to determine if a client IP address is on the same local subnet. When a client IP address is on a different subnet, all packets must be sent to the Default Gateway. Contact your network administrator to determine if subnetting is being used and for the correct Subnet Mask. If you change the Subnet Mask, you must cycle power on the 34980A to activate the setting. The default Subnet Mask for the 34980A is “255.255.0.0”. If DHCP is enabled, the specified Subnet Mask is not used. However, if the DHCP server fails to assign a valid IP address, the currently configured Subnet Mask will be used. Dot- notation addresses (“nnn.nnn.nnn.nnn” where “nnn” is a byte value) must be expressed with care, as most web software on the computer will interpret byte values with leading zeros as octal numbers. For example, “255.255.020.011” is actually equivalent to decimal “255.255.16.9” not “255.255.20.11” because “.020” is interpreted as “16” expressed in octal, and “.011” as “9”. To avoid confusion, use only decimal expressions of byte values (0 to 255), with no leading zeros. For example, the 34980A assumes that all dot- notation addresses are expressed as decimal byte values and strips all leading zeros from these byte values. Thus, attempting to set a Subnet Mask of “255.255.020.011” will become “255.255.20.11” (a purely decimal expression). Be sure to enter the exact expression, “255.255.20.11”, in your computer web software to address the instrument. Do not use “255.255.020.011” — the the computer will interpret this address differently due to the leading zeros. A value of “0.0.0.0” or “255.255.255.255” indicates that subnetting is not being used. The Subnet Mask is stored in non- volatile memory, and does not change when power has been off, after a Factory Reset (*RST command), or after an Instrument Preset (SYSTem:PRESet command). Front Panel Operation: Utility > REMOTE I/O > LAN > LAN SETTINGS > MODIFY > DHCP OFF > AUTO IP OFF > . . . SUBNET MASK Remote Interface Operation: SYSTem:COMMunicate:LAN:SMASk "" Agilent 34980A Mainframe User’s Guide 73
Page 1 and 2:
Agilent 34980A Multifunction Switc
Page 3:
Additional Safety Notices The follo
Page 6 and 7:
Menu Example 4: Configuring a Chann
Page 8 and 9:
Error Conditions. . . . . . . . . .
Page 10 and 11:
1 Introduction to the 34980A Data A
Page 12 and 13:
1 Introduction to the 34980A Web Br
Page 14 and 15:
1 Introduction to the 34980A Plug-I
Page 16 and 17:
1 Introduction to the 34980A Signal
Page 18 and 19:
1 Introduction to the 34980A RF and
Page 20 and 21:
1 Introduction to the 34980A If the
Page 22 and 23:
1 Introduction to the 34980A You ca
Page 24 and 25:
1 Introduction to the 34980A The Di
Page 26 and 27:
1 Introduction to the 34980A Contro
Page 28 and 29:
1 Introduction to the 34980A The Ac
Page 30 and 31: 2 Getting Started Front Panel at a
Page 32 and 33: 2 Getting Started Rear Panel Connec
Page 34 and 35: 2 Getting Started Installing and Co
Page 36 and 37: 2 Getting Started 2 Remove the two
Page 38 and 39: 2 Getting Started 3 Make connection
Page 40 and 41: 2 Getting Started Instrument Rack M
Page 42 and 43: 2 Getting Started Operating the 349
Page 44 and 45: 2 Getting Started Configure Key Gro
Page 46 and 47: 2 Getting Started Menu Example 2: O
Page 48 and 49: 2 Getting Started Menu Example 3: C
Page 50 and 51: 2 Getting Started Menu Example 4: C
Page 52 and 53: 2 Getting Started 11 To stop the co
Page 54 and 55: 2 Getting Started Connecting Over L
Page 56 and 57: 2 Getting Started 4 Press EXIT MENU
Page 58 and 59: 2 Getting Started 4 Press EXIT MENU
Page 60 and 61: 2 Getting Started Connecting Over U
Page 62 and 63: 2 Getting Started Launching the Web
Page 64 and 65: 2 Getting Started Selecting the “
Page 66 and 67: 2 Getting Started Modifying the Cha
Page 68 and 69: 2 Getting Started b Select commonly
Page 70 and 71: 2 Getting Started 62 Agilent 34980A
Page 72 and 73: 3 Features and Functions Front Pane
Page 74 and 75: 3 Features and Functions Basic Oper
Page 76 and 77: 3 Features and Functions Remote Int
Page 78 and 79: 3 Features and Functions DHCP DHCP
Page 82 and 83: 3 Features and Functions Default Ga
Page 84 and 85: 3 Features and Functions DNS Server
Page 86 and 87: 3 Features and Functions Clearing 3
Page 88 and 89: 3 Features and Functions Electrical
Page 92 and 93: 3 Features and Functions Analog Bus
Page 94 and 95: 3 Features and Functions Measuremen
Page 96 and 97: 3 Features and Functions Custom A/D
Page 98 and 99: 3 Features and Functions Trigger De
Page 100 and 101: 3 Features and Functions Safety Int
Page 104 and 105: 3 Features and Functions Temperatur
Page 108 and 109: 3 Features and Functions Thermistor
Page 110 and 111: 3 Features and Functions AC Low Fre
Page 112 and 113: 3 Features and Functions Current Me
Page 114 and 115: 3 Features and Functions Mx+B Scali
Page 116 and 117: 3 Features and Functions Scanning T
Page 118 and 119: 3 Features and Functions At the end
Page 120 and 121: 3 Features and Functions Scan Trigg
Page 124 and 125: 3 Features and Functions External S
Page 126 and 127: 3 Features and Functions Sample Cou
Page 128 and 129: 3 Features and Functions Channel De
Page 130 and 131:
3 Features and Functions AC Voltage
Page 132 and 133:
3 Features and Functions Non-Sequen
Page 134 and 135:
3 Features and Functions Remote Int
Page 136 and 137:
3 Features and Functions Front Pane
Page 138 and 139:
3 Features and Functions ABus1 HI A
Page 140 and 141:
3 Features and Functions Alarm Limi
Page 142 and 143:
3 Features and Functions The follow
Page 144 and 145:
3 Features and Functions Using the
Page 146 and 147:
3 Features and Functions Using Alar
Page 148 and 149:
3 Features and Functions Sequences
Page 150 and 151:
3 Features and Functions A sequence
Page 152 and 153:
3 Features and Functions Executing
Page 154 and 155:
3 Features and Functions Deleting S
Page 156 and 157:
3 Features and Functions Product Fi
Page 158 and 159:
3 Features and Functions Error Cond
Page 160 and 161:
3 Features and Functions You can di
Page 162 and 163:
3 Features and Functions Relay Cycl
Page 164 and 165:
3 Features and Functions Calibratio
Page 166 and 167:
3 Features and Functions Factory Re
Page 168 and 169:
3 Features and Functions Instrument
Page 170 and 171:
3 Features and Functions 162 Agilen
Page 172 and 173:
4 Introduction to the Plug-In Modul
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Index date, 153 dc current measurem
Page 182 and 183:
Index Sequence key, 36 sequences ca
Page 184:
Index 176 Agilent 34980A Mainframe
show all

Agilent 34980A  Multifunction Switch/Measure Unit *34980-90005*

Create successful ePaper yourself

Delete template?

Save as template?

Agilent 34980A  Multifunction Switch/Measure Unit 34980-90005