1935 Cadillac - GM Heritage Center
1935 Cadillac - GM Heritage Center
1935 Cadillac - GM Heritage Center
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Fisher Body Service Manual, <strong>1935</strong><br />
UPPER REAR QUARTER TRIM REMOVAL<br />
The Upper Rear Quarter Trim is assembled to the Cardboard<br />
Foundation before it is installed in the Body. This complete<br />
Assembly is removed as follows:<br />
may be loosened sufficiently to make the needed adjustment,<br />
while in cases of damage, to the Trim Pad itself, complete removal<br />
may be necessary. To completely remove a Door Trim<br />
Pad proceed as follows:,<br />
1. Remove the Door Window Garnish Molding.<br />
2. Remove the Door Arm Rest.<br />
3. Remove the Regulator and Remote Control Handles.<br />
4. Remove the Inside Safety Lock Rod Handle.<br />
5. Untack the Trim Pad from the top edges of the Regulator<br />
Board.<br />
6. Turn down the cloth of the Trim Pad and remove the<br />
tacks holding the Cardboard Foundation of this Assembly<br />
to the Regulator Board.<br />
7. Starting in the vicinity of the Door Lock, insert a screws<br />
driver between the Trim Pad and the Door Lock Pillar<br />
and pry the Pad loose.<br />
8. Follow this procedure and pry the Pad loose from the<br />
Door Hinge Pillar.<br />
9. Finish this operation by detaching the Pad from the Door<br />
Bottom Board in a similar manner.<br />
SUN VISOR INSTALLATION<br />
The Sun Visor on the left side above the Windshield is<br />
standard on most style Bodies. On some, the right side Sun<br />
Visor is also standard equipment.<br />
On those cars having only the left side installation, if the<br />
right side one is to be added, care should be used not to tear the<br />
Headlining when placing the Bracket in position.<br />
The Headlining has to be stretched tightly for appearance<br />
Illustration No. 93<br />
Upper Quarter Trim Removal.<br />
1. Remove the Rear Seat Cushion and Cushion Back.<br />
2. Remove the Rear Quarter Window Garnish Molding.<br />
3. Loosen and turn back the Trim qji top of the Parcel Shelf<br />
Board at corner.<br />
4. Untack the Trim around the upper and rear part of the<br />
Quarter Window Opening, also from the top of the Parcel<br />
Shelf Board at the corners.<br />
5. Remove tacks holding the Cardboard Foundation of this<br />
Assembly to the Rear Body Hinge Pillar, Side Roof Rail<br />
Filler, Rear Quarter Pillar and upper Rear Quarter<br />
Trim Stick.<br />
DOOR TRIM PAD REMOVAL<br />
In order to adjust or repair Door Mechanical Hardware<br />
Parts, it may be necessary to remove the Trim Pad from the<br />
Door. In some cases, the upper or lower part of this Assembly<br />
Illustration No. 95<br />
Sun Visor Installation.<br />
Illustration No. 94<br />
Door Trim Pad Removal.<br />
sake and the added tension of the Bracket may tear it loose<br />
at the edges. By gently smoothing it toward the Roof Side<br />
Rail, enough slack may be gained to suffice.<br />
NOTE—If Headlining is stretched too tight at this point<br />
it may be a good policy to loosen it at this corner to prevent<br />
tearing.<br />
As shown in Illustration No. 95 locate the threaded holes<br />
and install the Visor Bracket and Screws. The locations for<br />
the Socket and Escutcheon, above the Windshield and above<br />
the Door Opening may easily be found after the Visor Pivot<br />
Bracket is screwed into place. By cutting a hole through the<br />
Trim and Foundation Cardboard at these locations the Escutcheons<br />
may be pressed into the openings provided.<br />
Page 29