AJA FS1 Installation and Operation Guide

More documents

Recommendations

Info

104 The trap message would be sent to server-based external network management systems (NMS). These trap destinations must have a fixed IP address that you have pre-defined (FS1 parameters 51.2 and 51.4 must be set to point to these, if used). 51.2 SNMP Trap Dest 1 Description of Choices Parameter Adjustments: variable Using the Adjust buttons, enter the IP address of the destination where SNMP command messages (called “traps”) will be sent. This is usually an SNMP client (“NMS” or Network Management System) somewhere on your LAN. Default: 192.168.0.3 51.4 SNMP Trap Dest 2 Description of Choices Parameter Adjustments: variable Using the Adjust buttons, enter the IP address of the destination where SNMP command messages (called “traps”) will be sent. This is usually an SNMP client (“NMS” or Network Management System) somewhere on your LAN. Default: 192.168.0.3 For example, the FS1 could send a trap message if one of its redundant power supplies becomes unplugged. A client software agent that communicates with the NMS might then get a message telling the operator what has happened. Parameter 51.3 and 51.5 determine the SNMP Port(s) used for sending the trap messages. UDP Port 162 is the default used for SNMP trap messages. However, if this port is being used by another protocol or service, you can change the setting by modifying these parameters. 51.3 SNMP Trap Port 1 Description of Choices Parameter Adjustments: variable Using the Adjust buttons, select a UDP port for sending FS1 trap messages. Default: 162 51.5 SNMP Trap Port 2 Description of Choices Parameter Adjustments: variable Using the Adjust buttons, select a UDP port for sending FS1 trap messages. Default: 162
Formats 525i 625i 1080i 50/59.94/60 Hz 1080psf 23.98/24 Hz 720p 50/59.94/60 Hz Video Inputs and Outputs Video A/D, D/A Dual SDI/HD-SDI, SMPTE 259/274/292/296 HD component YPbPr/RGB (RGB is output only), SMPTE-274 SD component/composite/YC (S-Video) 12 bits 2x oversampled (HD) 4x oversampled (SD) Audio Inputs and Outputs Audio levels LAN 8 Channel Balanced, 25 pin D (Tascam pinout) 8 Channel AES (BNC) 8 Channel SDI/HD-SDI Embedded +12dBu, +15dBu, +18dBu, +24dBu, (Full Scale Digital) 10/100 automatic configuration Automatic cable crossover (auto MDI-X) Embedded web server HTTP v1.1 SNMP VTECS protocol for Remote Control Panel Appendix A: Specifications A1
Page 1 and 2:
B e c a u s e i t m a t t e r s . w
Page 3:
Limited Warranty Important Safety I
Page 6 and 7:
vi Reference Video (looping). . . .
Page 8 and 9:
viii 21.2 Audio Phase Ch2 . . . . .
Page 10 and 11:
x Canadian ICES Statement . . . . .
Page 12 and 13:
2 FS1 Front Panel Control • HD cr
Page 14 and 15:
4 w/Embedded Audio Analog Audio Inp
Page 17 and 18:
Controls and Indicators Chapter 2:
Page 19 and 20:
FS1 Installation and Operation Manu
Page 21 and 22:
Page 23 and 24:
About Video and Format Compatibilit
Page 25 and 26:
Connector Descriptions • 10/100 L
Page 27:
Page 30 and 31:
20 Warning! To meet safety regulati
Page 32 and 33:
22 Unpacking Shipping Box Contents
Page 34 and 35:
24 Networking the FS1 via DHCP The
Page 36 and 37:
26 Networking the FS1 using the Fac
Page 38 and 39:
28 Uploading and Installing the Sof
Page 40 and 41:
30 Power Requirements System Video/
Page 42 and 43:
32 RP-155), so the +24 dBu setting
Page 44 and 45:
34 Pressing either a parameter Sele
Page 46 and 47:
36 1.3 Component Out This parameter
Page 48 and 49:
38 2.11 Audio Map Ch1 This paramete
Page 50 and 51:
40 2.21 Audio Map Ch 1/2 This param
Page 52 and 53:
42 3.4 NTSC Standard 4.1 Analog Aud
Page 54 and 55:
44 4.5 Audio Follow Video 4.6 AFV M
Page 56 and 57:
46 5.2 Downconvert Mode This parame
Page 58 and 59:
48 5.3 SD Aspect Ratio Convert This
Page 60 and 61:
50 5.6 AFD Out SDI 1 5.7 AFD Out SD
Page 62 and 63:
52 6.4 Analog Output Fine (Horizont
Page 64 and 65: 54 10.2 Proc Amp Gain 10.3 Proc Amp
Page 66 and 67: 56 20.2 Audio Level Ch2 20.3 Audio
Page 68 and 69: 58 21.5 Audio Phase Ch5 21.6 Audio
Page 70 and 71: 60 31.1 Upconvert Line 21 31.1 Upco
Page 72 and 73: 62 36.1 GPI IN 1 Response The setti
Page 74 and 75: 64 37.1 GPI 1 OUT 37.2 GPI 2 OUT Th
Page 76 and 77: 66 50.1 IP Config 50.2 IP Address T
Page 78 and 79: 68 50.5 System Name 50.6 MAC Addres
Page 80 and 81: 70 51.3 SNMP Trap Port 1 This param
Page 82 and 83: 72 60.2 Format Alarm 60.3 Reference
Page 84 and 85: 74 91.1 Preset Recall 92.1 Preset S
Page 87 and 88: Remote FS1 Control Via a Web Browse
Page 89 and 90: Resetting Values To Factory Setting
Page 91 and 92: Embed Audio Out (4.3) On (default)
Page 93 and 94: Audio Control Screen FS1 Installati
Page 95 and 96: Convert Mode Screen Stereo Map Chan
Page 97 and 98: AFD Out SDI1 (5.6) Off (Default) Au
Page 99 and 100: ProcAmp Control Screen FS1 Installa
Page 101 and 102: FS1 Installation and Operation Manu
Page 103 and 104: Miscellaneous Screen FS1 Installati
Page 105 and 106: No Action (default) Freeze FS1 Inst
Page 109 and 110: Test Signals Screen FS1 Installatio
Page 113: FS1 Simple Network Management Proto
Page 117 and 118: GPI Connections 5 4 3 2 1 9 8 7 6 G
Page 119 and 120: Analog Audio Connections Connector
Page 121 and 122: Federal Communications Commission (
Page 124 and 125: 114 Before Operating Your FS1 Unit,
Page 126 and 127: 116 Attenzione! Questo dispositivo
Page 128 and 129: 118 Avviso! Proteggere il cavo di a
Page 130 and 131: 120 16:9 Refers to the aspect ratio
Page 132 and 133: 122 Processing Amplifier (Proc Amp)
Page 134 and 135: 124 C Cable Connections 7, 30 Cabli
Page 136 and 137: 126 1.3 Component Out 36 10.1 Proc
Page 138: 128 Video Format Status 9 Video In
show all

AJA FS1 Installation and Operation Guide

Create successful ePaper yourself

Delete template?

Save as template?