AJA FS1 Installation and Operation Guide

40
2.21 Audio Map Ch 1/2
This parameter is used with parameter 2.2—when Stereo Map is selected—to specify
the source of the channel pair for audio output channels 1 and 2. Possible choices
(24 in all) are:
2.21 Audio Map Ch1/2 Description of Choices
Parameter Adjustments:
AES Ch 1/2 (default)
AES Ch 3/4
AES Ch 5/6
AES Ch 7/8
Analog Ch 1/2
Analog Ch 3/4
Analog Ch 5/6
Analog Ch 7/8
SDI 1 Ch 1/2
SDI 1 Ch 3/4
SDI 1 Ch 5/6
SDI 1 Ch 7/8
SDI 2 Ch 1/2
SDI 2 Ch 3/4
SDI 2 Ch 5/6
SDI 2 Ch 7/8
SDI 1 Ch 9/10
SDI 1 Ch 11/12
SDI 1 Ch 13/14
SDI 1 Ch 15/16
SDI 2 Ch 9/10
SDI 2 Ch 11/12
SDI 2 Ch 13/14
SDI 2 Ch 15/16
Mute
2.22 Audio Map Ch 3/4
2.23 Audio Map Ch 5/6
Selects AES Channels 1/2, and maps them to Channel 1/2 audio out.
Selects AES Channels 3/4, and maps them to Channel 1/2 audio out.
Selects AES Channels 5/6, and maps them to Channel 1/2 audio out.
Selects AES Channels 7/8, and maps them to Channel 1/2 audio out.
Selects Analog Channels 1/2, and maps them to Channel 1/2 audio out.
Selects Analog Channels 3/4, and maps them to Channel 1/2 audio out.
Selects Analog Channels 5/6, and maps them to Channel 1/2 audio out.
Selects Analog Channels 7/8, and maps them to Channel 1/2 audio out.
Selects SDI 1 Channels 1/2, and maps them to Channel 1/2 audio out.
Selects SDI 1 Channels 3/4, and maps them to Channel 1/2 audio out.
Selects SDI 1 Channels 5/6, and maps them to Channel 1/2 audio out.
Selects SDI 1 Channels 7/8, and maps them to Channel 1/2 audio out.
Selects SDI 2 Channels 1/2, and maps them to Channel 1/2 audio out.
Selects SDI 2 Channels 3/4, and maps them to Channel 1/2 audio out.
Selects SDI 2 Channels 5/6, and maps them to Channel 1/2 audio out.
Selects SDI 2 Channels 7/8, and maps them to Channel 1/2 audio out.
Selects SDI 1 Channels 9/10, and maps them to Channel 1/2 audio out.
Selects SDI 1 Channels 11/12, and maps them to Channel 1/2 audio out.
Selects SDI 1 Channels 13/14, and maps them to Channel 1/2 audio out.
Selects SDI 1 Channels 15/16, and maps them to Channel 1/2 audio out.
Selects SDI 2 Channels 9/10, and maps them to Channel 1/2 audio out.
Selects SDI 2 Channels 11/12, and maps them to Channel 1/2 audio out.
Selects SDI 2 Channels 13/14, and maps them to Channel 1/2 audio out.
Selects SDI 2 Channels 15/16, and maps them to Channel 1/2 audio out.
Mute Channel pair 1/2 (no audio)
Note: If parameter 4.5 Audio Follow Video is set to On, then Audio Map Ch1/2
selection is independently kept for each separate input: SDI 1, SDI 2, Composite,
S-Video, and Component. If Audio Follow Video is set to Off, then another Audio
Map Ch1/2 selection is used. This note applies to Parameters 2.21 through 2.24.
This parameter is used with parameter 2.2—when Stereo Map is selected—to specify
the source of the channel pair for audio output channels 3 and 4. Possible choices
are the same as parameter 2.21. Default = AES Ch 3/4.