Series 16/18/160/180-Model C Maintenance Manual, GFZ-62755EN ...

B–62755EN/01Numbers16–TC/MC, 160–TC/MC, 18–TC/MC, 180–TC/MC, 9464–bit RISC board, 153AAbnormal sound and vibration during rotation, 407AC spindle (analog interface), 279AC spindle (serial interface), 261Action against noise, 125Address, 213Adjusting reference position (dog method), 257Adjusting the color liquid crystal display and plasma display,179Adjusting the flat display, 179Air filter cleaning and replacement method, 176AL–01 (motor overheat), 400AL–02 (excessive deviation of speed), 401AL–06,07 (over speed), 402AL–09 (unit overheat/6S to 26S only), 403AL–10 (low input voltage), 404AL–11 (DC link excessive voltage), 405AL–12 (DC link excessive current), 406Alarm 300 (Request for reference position return), 336Alarm 301 to 305 (Absolute pulse coder is faulty), 337Alarm 306 to 308 (Absolute pulse coder battery is low), 339Alarm 350 (Serial pulse coder is abnormal), 342Alarm 351 (Serial pulse coder is abnormal), 343Alarm 400 (Overload), 344Alarm 401 (*DRDY signal turned off), 346Alarm 404 and 405 (*DRDY signal turned on), 348Alarm 410 (Excessive position error amount during stop), 349Alarm 411 (Excessive position error during move), 350Alarm 414 (Digital servo system is abnormal), 352Alarm 416 (Disconnection alarm), 364Alarm 417 (Digital servo system is abnormal), 365Alarm 700 (Overheat at control side), 366Alarm 704 (Spindle speed fluctuation detection alarm), 367Alarm 749 (Serial spindle communication error), 368Alarm 750 (Spindle serial link cannot be started), 370Alarm 751,761 (Spindle alarm), 373Alarm 85 to 87 (Reader/puncher interface alarm), 325Alarm 90 (Reference position return is abnormal), 334Alarm 900 (ROM parity error), 374Alarm 914 to 915 (SRAM parity), 375Alarm 916 (DRAM parity error), 377Alarm 920, 922 (Watch dog or ram parity), 378Alarm 924 (Servo module mounting error), 381Alarm 930 (CPU error), 382IndexAlarm 950 (PMC system alarm), 383Alarm 951 (PMC–WATCH DOG alarm), 385Alarm 972 (NMI alarm in other board), 386Alarm 973 (NMI alarm by unknown cause), 387Alarm display, 27Alarm history screen, 27Alarm List, 419Analog signal interface, 124Applicable models, 2Associated parameters, 260Automatic operation cannot be done, 313Automatic setting of standard parameter, 278BBackground graphic board, 151Block diagram, 280Boot slot configuration screen, 479Boot system, 477Built–in debug function, 214CCalculation of S analog voltage and associated parameters, 281Cleaning heat exchanger, 177Clearing alarm history, 27Clearing CAP–II data (16–T), 208Clearing CAP–II memory, 209Combining serial spindle and analog spindle, 116Configuration display of software, 23Configuration of PCBs, 24Confirmation of transistor module, 409Confirming power supply (serial interface), 267Confirming the parameters required for data output, 186Connection to a serial spindle amplifier, 118Connection to analog spindle amplifier, 120Connection to serial spindle amplifier, 119Connections by type of detectors, 115Contents displayed, 54Control unit P.C.B., 155Control unit rack, 154Corrective action for failures, 297Correspondence between operation mode an parameters onspindle tuning screen, 275CRT/MDI unit, 98, 159Cycle start LED signal has turned off, 321DData sampling for storage type waveform diagnosis, 75i–1