B.A.S.I.S. G Service Manual [T63300] - Best Access Systems

More documents

Recommendations

Info

Servicing Exit Hardware Trim Escutcheon PartsSERVICING THE YOKEEach time you service the yoke you need to replace the following partswith new parts:■ escutcheon gasket (C64564)■ cable tie■ lift finger screw (page 4–9)■ mounting plate screws (page 4–9)■ 4 shoulder screws (page 4–10).Removing the yoke1. Remove the following parts:■ escutcheon from the door (page 8–13)■ mounting standoffs (page 10–2)■ escutcheon gasket (page 10–3)■ lift finger (page 10–4)■ mounting plate (page 10–6)■ lever return springs (page 10–8).2. Unscrew the 4 shoulder screws and discard. See Figure 10.12.3. Remove the yoke from the escutcheon.Shoulder screwsYokeShoulder screwsFigure 10.12 Removing and reinstalling the yoke10–20 B.A.S.I.S. G Service Manual
Servicing Exit Hardware Trim Escutcheon PartsReinstalling theyoke1. Position the yoke in the escutcheon with the threaded nut down.2. Apply Lubriplate ® GR-132 grease or an equivalent quality petroleumaround the slots on the face of the yoke.3. Tightly secure the yoke to the escutcheon using the 4 new shoulderscrews (20–25 lbs. torque). See Figure 10.12.4. Reinstall the following parts:■ lever return springs (page 10–8)■ mounting plate (page 10–7)■ lift finger (page 10–5)■ escutcheon gasket (page 10–3)■ mounting standoffs (page 10–2)■ escutcheon on the door (page 8–14).B.A.S.I.S. G Service Manual 10–21
Page 1 and 2:
SERVICE MANUALSERVICE MANUAL
Page 3 and 4:
CONTENTSFIGURESXIGETTING STARTED 1-
Page 5 and 6:
ContentsSERVICING STANDARD MORTISE
Page 7 and 8:
ContentsServicing the cylinder 8-10
Page 9 and 10:
ContentsServicing the yoke 10-20Rem
Page 11 and 12:
FIGURESGETTING STARTEDSystem overvi
Page 13 and 14:
FiguresRemoving the inside rose lin
Page 15 and 16:
FiguresB.A.S.I.S. Transport Diagnos
Page 17 and 18:
1 GETTING STARTEDINTRODUCTIONThe B.
Page 19 and 20:
Getting StartedPersonal computer ru
Page 21 and 22:
Getting StartedCERTIFICATIONS AND S
Page 23 and 24:
Getting StartedDocument TitleG09 In
Page 25 and 26:
2 STANDARD FUNCTIONS ANDPARTSThe fo
Page 27 and 28:
Standard Functions and PartsLV-Dead
Page 29 and 30:
B.A.S.I.S. G Service Manual 2-5TRIM
Page 31 and 32:
Standard Functions and PartsItem Pa
Page 33 and 34:
Standard Functions and PartsSmart c
Page 35 and 36:
B.A.S.I.S. G Service Manual 2-11DUA
Page 37 and 38:
Standard Functions and PartsItem Pa
Page 39 and 40:
Standard Functions and PartsMortise
Page 41 and 42:
Standard Functions and PartsOther m
Page 43 and 44:
Standard Functions and PartsCylindr
Page 45 and 46:
3 EXIT HARDWARE TRIMFUNCTIONS AND P
Page 47 and 48:
B.A.S.I.S. G Service Manual 3-3TRIM
Page 49 and 50:
Exit Hardware Trim Functions and Pa
Page 51 and 52:
Page 53 and 54:
B.A.S.I.S. G Service Manual 3-9DUAL
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
4 SHARED STANDARD AND EXITHARDWARE
Page 61 and 62:
Shared Standard and Exit Hardware T
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
OTHER SYSTEM COMPONENTSOther system
Page 71 and 72:
5 SERVICING STANDARDMORTISE TRIM PA
Page 73 and 74:
Servicing Standard Mortise Trim Par
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
6 SERVICING STANDARDMORTISE CASE PA
Page 91 and 92:
Servicing Standard Mortise Case Par
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
7 SERVICING CYLINDRICAL PARTSThis c
Page 111 and 112:
Servicing Cylindrical PartsSERVICIN
Page 113 and 114:
Page 115 and 116:
Servicing Cylindrical Partsb. Remov
Page 117 and 118:
Servicing Cylindrical Parts2. Insta
Page 119 and 120:
Servicing Cylindrical Parts4. Conne
Page 121 and 122:
Servicing Cylindrical PartsCautionC
Page 123 and 124:
Page 125 and 126:
Servicing Cylindrical Parts6. Tight
Page 127 and 128:
8 SERVICING EXIT HARDWARETRIM PARTS
Page 129 and 130:
Servicing Exit Hardware Trim PartsR
Page 131 and 132:
Page 133 and 134:
Page 135 and 136: Servicing Exit Hardware Trim PartsS
Page 137 and 138: Servicing Exit Hardware Trim PartsR
Page 139 and 140: Servicing Exit Hardware Trim PartsS
Page 141 and 142: 9 SERVICING STANDARDOUTSIDE ESCUTCH
Page 143 and 144: Servicing Standard Outside Escutche
Page 167 and 168: 10 SERVICING EXIT HARDWARETRIM ESCU
Page 169 and 170: Servicing Exit Hardware Trim Escutc
Page 185: Servicing Exit Hardware Trim Escutc
Page 197 and 198: 11 MAINTENANCEThis chapter includes
Page 199 and 200: MaintenanceReinstalling thebackup b
Page 201 and 202: MaintenanceInside escutcheonBattery
Page 203 and 204: Maintenance4. Use a T15 TORX bit dr
Page 205 and 206: MaintenanceReinstalling thebattery
Page 207 and 208: Maintenance6. For B.A.S.I.S. mortis
Page 209 and 210: MaintenancePERFORMING DIAGNOSTICS U
Page 211 and 212: MaintenancePDASerial cableCommunica
Page 213 and 214: MaintenanceNote: To perform other a
Page 215 and 216: MaintenanceUnlocking a doortemporar
Page 217 and 218: 12 TROUBLESHOOTINGThis chapter cont
Page 219 and 220: TroubleshootingENABLING COMMUNICATI
Page 221 and 222: Troubleshooting8. For standard lock
Page 223 and 224: TroubleshootingRESPONDING TO PROBLE
Page 225 and 226: TroubleshootingLEDs Sounder Access
Page 227 and 228: TroubleshootingWhen communicatingbe
Page 229 and 230: A LOCK HISTORY EVENT TYPESThe follo
Page 231 and 232: Lock History Event TypesEventREADER
Page 233 and 234: B INSTALLATION INSTRUCTIONSThe foll
Page 235 and 236: Planning the installationContentsTh
Page 237 and 238:
Preparing the door and door jamb3 M
Page 239 and 240:
Preparing the door and door jambIns
Page 241 and 242:
Installing the lock9 Install core (
Page 243 and 244:
Installing the lockInstallation Ins
Page 245 and 246:
Page 247 and 248:
Completing the installationInstalla
Page 249 and 250:
Completing the installation20 Test
Page 251 and 252:
Planning the installationInstallati
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Installing the lock13 Make motor co
Page 261 and 262:
Completing the installation17 Insta
Page 263 and 264:
Planning the installationContentsTh
Page 265 and 266:
Preparing the doorInstallation Inst
Page 267 and 268:
Preparing the doorInstallation Inst
Page 269 and 270:
Installing the exit hardware and tr
Page 271 and 272:
Installing the exit hardware and tr
Page 273 and 274:
Completing the installationInstalla
Page 275 and 276:
C INDEXAadding key override sensing
Page 277 and 278:
IndexLlatch 2-20latch leverpart dra
Page 279 and 280:
Indextechnical documentation packag
show all

B.A.S.I.S. G Service Manual [T63300] - Best Access Systems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?