B.A.S.I.S. G Service Manual [T63300] - Best Access Systems

More documents

Recommendations

Info

Installation Instructions for B.A.S.I.S. Mortise Locks© 2002 Best Lock Corporation dba Best Access Systems.T61836/Rev – 1854161 ER-7991-12 February 200216BEST ACCESS SYSTEMSIndianapolis, Indiana
Planning the installationInstallation Instructions forB.A.S.I.S. Cylindrical LocksContentsThese installation instructions describe how to install yourB.A.S.I.S.® G (93KG–95KG) or B.A.S.I.S. V (93KBV–95KBV)Cylindrical Lock. The following topics are covered. †Planning the installation ................................................ 1Preparing the door and door jamb ................................ 2Installing the lock ............................................................ 6Completing the installation..........................................10Site surveyUse the following survey to record information about theinstallation site. You need this information to determinehow to prepare the door for the lock.Door informationDoor handing and bevel:❑ Left hand (LH)❑ Left hand, reverse bevel (LHRB)❑ Right hand (RH)❑ Right hand, reverse bevel (RHRB)Door thickness: inches (1 3/4″ to 2 1/4″)Environment informationAmbient temperature:❑ Is within specifications. See the tables below.This product meets the following Locked Door Outdoortest requirements for ANSI/BHMA 156.25:Side of door RangeInside+66°F to +74°F (+19°C to +23°C)Outside–31°F to +151°F (–35°C to +66°C)This product meets the following Full Indoor testrequirements for ANSI/BHMA 156.25:Side of door RangeInside and outside +32°F to +120°F (0°C to +42°C)† The Best Access Systems logo and B.A.S.I.S. areregistered trademarks of Best Lock Corporation.Components checklistUse the following checklist to make sure that you have theitems necessary to install your B.A.S.I.S. Cylindrical Lock.Components provided in the box:❑ Chassis with outside lever and outside rose linerassembly❑ Inside escutcheon assembly❑ Battery compartment door❑ Battery pack❑ Inside rose liner❑ Outside escutcheon assembly❑ Inside lever❑ Throw member package❑ Latch❑ Hub washers❑ Trim hole insert package❑ Plastic bushing package❑ Escutcheon screw package❑ Strike package❑ Bar code ID sticker (for your records)❑ Temporary operator card❑ Installation template and instructionsOther components:❑ Core❑ Control keySpecial tools checklistUse the following checklist to make sure that you have thespecial tools necessary to install your B.A.S.I.S. CylindricalLock.❑ KD303 Drill jig❑ T15 TORX® bit driver ‡❑ KD325 Strike plate locating pin❑ KD315 Faceplate marking chisel‡ TORX is a registered trademark of the CamcarDivision of Textron.BEST ACCESS SYSTEMSIndianapolis, Indiana1
Page 1 and 2:
SERVICE MANUALSERVICE MANUAL
Page 3 and 4:
CONTENTSFIGURESXIGETTING STARTED 1-
Page 5 and 6:
ContentsSERVICING STANDARD MORTISE
Page 7 and 8:
ContentsServicing the cylinder 8-10
Page 9 and 10:
ContentsServicing the yoke 10-20Rem
Page 11 and 12:
FIGURESGETTING STARTEDSystem overvi
Page 13 and 14:
FiguresRemoving the inside rose lin
Page 15 and 16:
FiguresB.A.S.I.S. Transport Diagnos
Page 17 and 18:
1 GETTING STARTEDINTRODUCTIONThe B.
Page 19 and 20:
Getting StartedPersonal computer ru
Page 21 and 22:
Getting StartedCERTIFICATIONS AND S
Page 23 and 24:
Getting StartedDocument TitleG09 In
Page 25 and 26:
2 STANDARD FUNCTIONS ANDPARTSThe fo
Page 27 and 28:
Standard Functions and PartsLV-Dead
Page 29 and 30:
B.A.S.I.S. G Service Manual 2-5TRIM
Page 31 and 32:
Standard Functions and PartsItem Pa
Page 33 and 34:
Standard Functions and PartsSmart c
Page 35 and 36:
B.A.S.I.S. G Service Manual 2-11DUA
Page 37 and 38:
Standard Functions and PartsItem Pa
Page 39 and 40:
Standard Functions and PartsMortise
Page 41 and 42:
Standard Functions and PartsOther m
Page 43 and 44:
Standard Functions and PartsCylindr
Page 45 and 46:
3 EXIT HARDWARE TRIMFUNCTIONS AND P
Page 47 and 48:
B.A.S.I.S. G Service Manual 3-3TRIM
Page 49 and 50:
Exit Hardware Trim Functions and Pa
Page 51 and 52:
Page 53 and 54:
B.A.S.I.S. G Service Manual 3-9DUAL
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
4 SHARED STANDARD AND EXITHARDWARE
Page 61 and 62:
Shared Standard and Exit Hardware T
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
OTHER SYSTEM COMPONENTSOther system
Page 71 and 72:
5 SERVICING STANDARDMORTISE TRIM PA
Page 73 and 74:
Servicing Standard Mortise Trim Par
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
6 SERVICING STANDARDMORTISE CASE PA
Page 91 and 92:
Servicing Standard Mortise Case Par
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
7 SERVICING CYLINDRICAL PARTSThis c
Page 111 and 112:
Servicing Cylindrical PartsSERVICIN
Page 113 and 114:
Page 115 and 116:
Servicing Cylindrical Partsb. Remov
Page 117 and 118:
Servicing Cylindrical Parts2. Insta
Page 119 and 120:
Servicing Cylindrical Parts4. Conne
Page 121 and 122:
Servicing Cylindrical PartsCautionC
Page 123 and 124:
Page 125 and 126:
Servicing Cylindrical Parts6. Tight
Page 127 and 128:
8 SERVICING EXIT HARDWARETRIM PARTS
Page 129 and 130:
Servicing Exit Hardware Trim PartsR
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Servicing Exit Hardware Trim PartsS
Page 137 and 138:
Page 139 and 140:
Servicing Exit Hardware Trim PartsS
Page 141 and 142:
9 SERVICING STANDARDOUTSIDE ESCUTCH
Page 143 and 144:
Servicing Standard Outside Escutche
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
10 SERVICING EXIT HARDWARETRIM ESCU
Page 169 and 170:
Servicing Exit Hardware Trim Escutc
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
11 MAINTENANCEThis chapter includes
Page 199 and 200: MaintenanceReinstalling thebackup b
Page 201 and 202: MaintenanceInside escutcheonBattery
Page 203 and 204: Maintenance4. Use a T15 TORX bit dr
Page 205 and 206: MaintenanceReinstalling thebattery
Page 207 and 208: Maintenance6. For B.A.S.I.S. mortis
Page 209 and 210: MaintenancePERFORMING DIAGNOSTICS U
Page 211 and 212: MaintenancePDASerial cableCommunica
Page 213 and 214: MaintenanceNote: To perform other a
Page 215 and 216: MaintenanceUnlocking a doortemporar
Page 217 and 218: 12 TROUBLESHOOTINGThis chapter cont
Page 219 and 220: TroubleshootingENABLING COMMUNICATI
Page 221 and 222: Troubleshooting8. For standard lock
Page 223 and 224: TroubleshootingRESPONDING TO PROBLE
Page 225 and 226: TroubleshootingLEDs Sounder Access
Page 227 and 228: TroubleshootingWhen communicatingbe
Page 229 and 230: A LOCK HISTORY EVENT TYPESThe follo
Page 231 and 232: Lock History Event TypesEventREADER
Page 233 and 234: B INSTALLATION INSTRUCTIONSThe foll
Page 235 and 236: Planning the installationContentsTh
Page 237 and 238: Preparing the door and door jamb3 M
Page 239 and 240: Preparing the door and door jambIns
Page 241 and 242: Installing the lock9 Install core (
Page 243 and 244: Installing the lockInstallation Ins
Page 247 and 248: Completing the installationInstalla
Page 249: Completing the installation20 Test
Page 259 and 260: Installing the lock13 Make motor co
Page 261 and 262: Completing the installation17 Insta
Page 263 and 264: Planning the installationContentsTh
Page 265 and 266: Preparing the doorInstallation Inst
Page 267 and 268: Preparing the doorInstallation Inst
Page 269 and 270: Installing the exit hardware and tr
Page 271 and 272: Installing the exit hardware and tr
Page 273 and 274: Completing the installationInstalla
Page 275 and 276: C INDEXAadding key override sensing
Page 277 and 278: IndexLlatch 2-20latch leverpart dra
Page 279 and 280: Indextechnical documentation packag
show all

B.A.S.I.S. G Service Manual [T63300] - Best Access Systems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?