B.A.S.I.S. G Service Manual [T63300] - Best Access Systems

More documents

Recommendations

Info

TroubleshootingLEDs Sounder Access Possible causes include… You should…––– ––– Denied a. Card reader needs cleaning. a. Clean the card reader head using a cleaningcard for magnetic stripe card readers.Greenflashesb. Primary wire harness isdamaged or disconnected.c. Foreign object is inserted inthe card reader.b. Check the primary wire harness. If it’sdamaged, replace the wire harness. Forstandard locks, see page 9–7. For exithardware trim, see page 10–9.c. Remove the object or replace the reader.d. Battery pack is faulty. d. Check the battery pack. Replace it, ifnecessary. See page 11–4.e. Firmware has locked up due to e. Contact your local BEST Representative.incorrect sequence whenconnecting the battery pack.f. Primary wire harness isdisconnected from the motoror is damaged.g. Smart card reader is notproperly aligned in the bezelon the inside of the reader.(Smart card present switch isstuck.)h. For smart card readers,conformal coating has beenapplied to the flex cableconnector.i. Firmware is out-of-date orfaulty.j. Control electronics board ismalfunctioning.k. Control electronics boardfailed for an unknown reason.Note: If the above conditionexists, the key override may beused to access the door. If thedoor has no key override, callyour local BEST representative.f. Check the primary wire harness.For standard locks, see page 9–7. For exithardware trim, see page 10–9.g. Pop the smart card reader into place in thebezel.For standard locks, see page 9–22. Forexit hardware trim, see page 10–13.h. Remove the flex cable from the connectorand apply electrical contact cleaner onto theconnector. Reinstall the flex cable.For standard locks, see page 9–22. For exithardware trim, see page 10–13.i. Update the firmware. Contact your localBEST Representative.j. Replace the control electronics board.For standard locks, see page 9–10. For exithardware trim, see page 10–10.k. Replace the control electronics board.For standard locks, see page 9–10. For exithardware trim, see page 10–10.l. Reader has failed. l. Replace the reader. For standard locks, seepage 9–17. For exit hardware trim, seepage 10–12.––– Denied a. For a standard mortise lock,self-aligning trim isovertightened.a. Loosen the escutcheon mounting screws.See page 5–3.12–8 B.A.S.I.S. G Service Manual
TroubleshootingLEDs Sounder Access Possible causes include… You should…GreenflashesRed &greenflashesGreenstays onRedflashes3 longtones3 shorttonesGrantedafterdelayb. For a standard mortise lock,mounting plates areovertightened.c. For a standard cylindricallock, chassis type is set to“mortise”.d. For a standard cylindricallock, the spindle may be faulty.e. For exit hardware trim, thelocking plate is not properlypositioned.f. The trim or latchbolt is notproperly aligned.b. Loosen the mounting plates. See page 5–14.c. Change the programming setting for chassistype to cylindrical.d. If you can hear the chassis cycling, replacethe chassis. Contact your local BESTRepresentative for assistance.e. Reposition the locking plate.See page 10–18.f. Realign the trim or latchbolt.Battery is low (warning). Change the battery pack. See page 11–4.Denied Battery is very low (alarm). Change the battery pack. See page 11–4.––– Denied Communication card was used. Wait 1 minute for the communications mode toautomatically expire, or use any card again toturn off communications.––– Denied a. Sounder is damaged. a. Replace the reader.For standard locks, see page 9–17. For exithardware trim, see page 10–12.b. Control electronics board ismalfunctioning.c. Primary harness connection isdamaged or loose.b. Replace the control electronics board.For standard locks, see page 9–10. For exithardware trim, see page 10–10.c. Check the primary harness and replace theharness, if necessary. For standard locks, seepage 9–7. For exit hardware trim, seepage 10–9.––– ––– Granted a. LEDs are damaged. a. Replace the reader.For standard locks, see page 9–17. For exithardware trim, see page 10–12.b. Control electronics board ismalfunctioning.c. Smart card flex cable isbroken.b. Replace the control electronics board.For standard locks, see page 9–10. For exithardware trim, see page 10–10.c. Replace the smart card reader.For standard locks, see page 9–20. For exithardware trim, see page 10–13.B.A.S.I.S. G Service Manual 12–9
Page 1 and 2:
SERVICE MANUALSERVICE MANUAL
Page 3 and 4:
CONTENTSFIGURESXIGETTING STARTED 1-
Page 5 and 6:
ContentsSERVICING STANDARD MORTISE
Page 7 and 8:
ContentsServicing the cylinder 8-10
Page 9 and 10:
ContentsServicing the yoke 10-20Rem
Page 11 and 12:
FIGURESGETTING STARTEDSystem overvi
Page 13 and 14:
FiguresRemoving the inside rose lin
Page 15 and 16:
FiguresB.A.S.I.S. Transport Diagnos
Page 17 and 18:
1 GETTING STARTEDINTRODUCTIONThe B.
Page 19 and 20:
Getting StartedPersonal computer ru
Page 21 and 22:
Getting StartedCERTIFICATIONS AND S
Page 23 and 24:
Getting StartedDocument TitleG09 In
Page 25 and 26:
2 STANDARD FUNCTIONS ANDPARTSThe fo
Page 27 and 28:
Standard Functions and PartsLV-Dead
Page 29 and 30:
B.A.S.I.S. G Service Manual 2-5TRIM
Page 31 and 32:
Standard Functions and PartsItem Pa
Page 33 and 34:
Standard Functions and PartsSmart c
Page 35 and 36:
B.A.S.I.S. G Service Manual 2-11DUA
Page 37 and 38:
Standard Functions and PartsItem Pa
Page 39 and 40:
Standard Functions and PartsMortise
Page 41 and 42:
Standard Functions and PartsOther m
Page 43 and 44:
Standard Functions and PartsCylindr
Page 45 and 46:
3 EXIT HARDWARE TRIMFUNCTIONS AND P
Page 47 and 48:
B.A.S.I.S. G Service Manual 3-3TRIM
Page 49 and 50:
Exit Hardware Trim Functions and Pa
Page 51 and 52:
Page 53 and 54:
B.A.S.I.S. G Service Manual 3-9DUAL
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
4 SHARED STANDARD AND EXITHARDWARE
Page 61 and 62:
Shared Standard and Exit Hardware T
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
OTHER SYSTEM COMPONENTSOther system
Page 71 and 72:
5 SERVICING STANDARDMORTISE TRIM PA
Page 73 and 74:
Servicing Standard Mortise Trim Par
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
6 SERVICING STANDARDMORTISE CASE PA
Page 91 and 92:
Servicing Standard Mortise Case Par
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
7 SERVICING CYLINDRICAL PARTSThis c
Page 111 and 112:
Servicing Cylindrical PartsSERVICIN
Page 113 and 114:
Page 115 and 116:
Servicing Cylindrical Partsb. Remov
Page 117 and 118:
Servicing Cylindrical Parts2. Insta
Page 119 and 120:
Servicing Cylindrical Parts4. Conne
Page 121 and 122:
Servicing Cylindrical PartsCautionC
Page 123 and 124:
Page 125 and 126:
Servicing Cylindrical Parts6. Tight
Page 127 and 128:
8 SERVICING EXIT HARDWARETRIM PARTS
Page 129 and 130:
Servicing Exit Hardware Trim PartsR
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Servicing Exit Hardware Trim PartsS
Page 137 and 138:
Page 139 and 140:
Servicing Exit Hardware Trim PartsS
Page 141 and 142:
9 SERVICING STANDARDOUTSIDE ESCUTCH
Page 143 and 144:
Servicing Standard Outside Escutche
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
10 SERVICING EXIT HARDWARETRIM ESCU
Page 169 and 170:
Servicing Exit Hardware Trim Escutc
Page 171 and 172:
Servicing Exit Hardware Trim Escutc
Page 173 and 174: Servicing Exit Hardware Trim Escutc
Page 197 and 198: 11 MAINTENANCEThis chapter includes
Page 199 and 200: MaintenanceReinstalling thebackup b
Page 201 and 202: MaintenanceInside escutcheonBattery
Page 203 and 204: Maintenance4. Use a T15 TORX bit dr
Page 205 and 206: MaintenanceReinstalling thebattery
Page 207 and 208: Maintenance6. For B.A.S.I.S. mortis
Page 209 and 210: MaintenancePERFORMING DIAGNOSTICS U
Page 211 and 212: MaintenancePDASerial cableCommunica
Page 213 and 214: MaintenanceNote: To perform other a
Page 215 and 216: MaintenanceUnlocking a doortemporar
Page 217 and 218: 12 TROUBLESHOOTINGThis chapter cont
Page 219 and 220: TroubleshootingENABLING COMMUNICATI
Page 221 and 222: Troubleshooting8. For standard lock
Page 223: TroubleshootingRESPONDING TO PROBLE
Page 227 and 228: TroubleshootingWhen communicatingbe
Page 229 and 230: A LOCK HISTORY EVENT TYPESThe follo
Page 231 and 232: Lock History Event TypesEventREADER
Page 233 and 234: B INSTALLATION INSTRUCTIONSThe foll
Page 235 and 236: Planning the installationContentsTh
Page 237 and 238: Preparing the door and door jamb3 M
Page 239 and 240: Preparing the door and door jambIns
Page 241 and 242: Installing the lock9 Install core (
Page 243 and 244: Installing the lockInstallation Ins
Page 247 and 248: Completing the installationInstalla
Page 249 and 250: Completing the installation20 Test
Page 251 and 252: Planning the installationInstallati
Page 259 and 260: Installing the lock13 Make motor co
Page 261 and 262: Completing the installation17 Insta
Page 263 and 264: Planning the installationContentsTh
Page 265 and 266: Preparing the doorInstallation Inst
Page 267 and 268: Preparing the doorInstallation Inst
Page 269 and 270: Installing the exit hardware and tr
Page 271 and 272: Installing the exit hardware and tr
Page 273 and 274: Completing the installationInstalla
Page 275 and 276:
C INDEXAadding key override sensing
Page 277 and 278:
IndexLlatch 2-20latch leverpart dra
Page 279 and 280:
Indextechnical documentation packag
show all

B.A.S.I.S. G Service Manual [T63300] - Best Access Systems

Create successful ePaper yourself

Delete template?

Save as template?