Duality SE Operator's Manual - Solid State Logic

More documents

Recommendations

Info

DaWOther useful transport modesHalf-speed PlaybackAbort Current Record PassCycle through Record Modes (Normal, Quickpunch, TrackPunch, Loop)Cycle through Machine Control Masters (accessible via the transport window)Link or Unlink the Edit and TimelinessHIFt + playsHIFt + stOpCtrl + reCOrDCtrl + OnlInesHIFt + / (backslash)setting pre and post roll (15)Hold down alt and press the pre or pOst button to highlight the left hand numeric field of the pre-roll or postrolltime window; the time is displayed on Duality SE’s TFT screen in place of the DAW’s timecode position. The selectednumeric field will flash; use the navigation left/right arrow buttons (16) to select a different numeric field if required, thenenter a value on the numeric keypad (18) or use the up/down arrow buttons (16) to increase or decrease the selected field.Press enter on the numeric keypad (18) to confirm the time. The numeric keypad’s Clr button can be used to clearthe selected time.setting start (In) and end (Out) times (15)Hold down alt and press the In or OUT button to highlight the left hand numeric field of the start or end time window.The time is displayed on Duality SE’s TFT screen in place of the DAW timecode position. The selected numeric field willflash; use the navigation left/right arrow buttons (16) to select a different numeric field if required, then enter a value onthe numeric keypad (18) or use the up/down arrow buttons (16) to increase or decrease the selected field.Press enter on the numeric keypad (18) to confirm the time. The numeric keypad’s Clr button can be used to clearthe selected time.audition (15)This function allows the In, Out, pre and pOst points to be checked. Press the auD button, then press either thepre, In, Out, or pOst button. Press the auD button again to cancel the function.preInOutpOstalt + OptIOn + pre or InPlays from the pre-roll point to the selection start pointPlays from the selection start point for the post-roll timePlays from the end point less the pre-roll time to the end pointPlays from the selection end point for the post-roll timePlays from the selection start point less the pre-roll time to the selectionstart time plus the post-roll timealt + OptIOn + pOst or Out Plays from the selection end point to the selection end point plus post-rolltime.3-28 Duality se V3 Operator’s Manual
DaWFootswitch ControlDuality SE has two 1/4" jack footswitch connectors on the rear of the console. These are intended for hands-free accessto essential transport functions:Footswitch Control 1 either plays or stops the DAW. Holding down sHIFt will abort a recording if in record, or initiatehalf-speed playback if stopped.Footswitch Control 2 is used to activate or deactivate record mode. Holding Ctrl while pressing the footswitch willcycle through record modes.Zoom, navigation and selection Modes (16)The Motion Control area has a section with four cursor buttons and a ZOOM/sel function that toggles the selection ofthree available modes: navigation edit, Zoom and select.navigation Mode (Zoom/sel button not lit)In this mode the cursor buttons can be used to select a region or regions on the DAW screen.The left and right buttons will snap to region/clip boundaries. The up/down buttons move the cursor to the track above orbelow respectively. Holding down the sHIFt modifier button will allow a selection to be extended in any direction. Holdingthe OptIOn button allows the current selection point to be centred on the screen.Holding Ctrl + up/Down/left/right cursor button allows you to change and extend the region/clip selection. AddsHIFt to the above combination to include either the previous or next region.Zoom Mode (Zoom/sel button lit)The cursor buttons now become horizontal and vertical zoom controls for the edit/arrange window on the DAW.Fixed edit/arrange zoom settings can be saved or recalled from Duality SE’s numeric keypad:To save a zoom setting — press sHIFt + numeric keypad numberTo recall a zoom setting — press OptIOn + numeric keypad numberDuality se V3 Operator’s Manual3-29
Page 1:
Solid State LogicS O U N D V I S I
Page 4 and 5:
Manual ContentsFader Grouping 2-12F
Page 6 and 7:
Manual ContentsWorking with DaW aut
Page 8 and 9:
Manual ContentsseCtiOn 6: reMOte Br
Page 10 and 11:
This page is intentionally almost b
Page 12 and 13:
IntroductionThis page is intentiona
Page 14 and 15:
IntroductionCreative Versatility•
Page 16 and 17:
IntroductionThis page is intentiona
Page 18 and 19:
Page 20 and 21:
Console OperationsThis page is inte
Page 22 and 23:
Console OperationsSignal Processor
Page 24 and 25:
Console Operationsan Introduction t
Page 26 and 27:
Console OperationsAbove each bay of
Page 28 and 29:
Console Operationsrel/HOlD — This
Page 30 and 31:
Console OperationsChannel Output (C
Page 32 and 33:
Console OperationsChannel panAt the
Page 34 and 35:
Console OperationsMaster Channel Fa
Page 36 and 37:
Console OperationsTo edit any exist
Page 38 and 39:
Console Operations12342-16 Duality
Page 40 and 41:
Console OperationsCentral routing p
Page 42 and 43:
Console OperationsMain Output Funct
Page 44 and 45:
Console OperationsMaster FaderThe m
Page 46 and 47:
Console OperationsIf either MInI a
Page 48 and 49:
Console OperationsMonitor OptionsA
Page 50 and 51: Console OperationsMonitor speaker C
Page 52 and 53: Console OperationsMonitor level Dis
Page 54 and 55: Console OperationsCue/Fx send Maste
Page 56 and 57: Console OperationsMisc OptionsA num
Page 58 and 59: Console OperationsThe following opt
Page 60 and 61: Console OperationsMix reassign Matr
Page 62 and 63: Console OperationsCentre section Me
Page 64 and 65: Console Operationssetup MenuThe cen
Page 66 and 67: Console OperationsDaw setupThe next
Page 68 and 69: This page is intentionally almost b
Page 70 and 71: DaWplug-In editor 3-33Plug-In Edito
Page 72 and 73: DaWThis page is intentionally almos
Page 74 and 75: DaWConsole FocusThe console can be
Page 78 and 79: DaWConnecting via physical MIDI por
Page 80 and 81: DaWsetting your workstation(s) to c
Page 82 and 83: DaWlogic pro 8When Logic is assigne
Page 88 and 89: DaWDaW utility Buttons (9)This grou
Page 92 and 93: DaWChannel solo and Cut panelsChann
Page 94 and 95: DaWselect ModeWith the sel button (
Page 102 and 103: DaWselection Mode (Zoom/sel button
Page 106 and 107: DaWselecting a DaW Channel for plug
Page 108 and 109: DaWComparing your ChangesPressing t
Page 110 and 111: DaWedit tools MenuEdit Tools (edts)
Page 114 and 115: DaWautomation status DisplayPressin
Page 118 and 119: DaWThe majority of DAW functions ar
Page 120 and 121: DaWthe logic templateDuality SE emu
Page 122 and 123: DaWnuendo/Cubase templateAs with ot
Page 124 and 125: DaWDuality se’s nuendo Control sc
Page 126 and 127: DaWCHannel is unchanged and assigns
Page 128 and 129: DaWThe Transport Control buttons ar
Page 132 and 133: total recallThis page is intentiona
Page 136 and 137: total recalltOtal reCall anD prOjeC
Page 138 and 139: total recallrecalling a tr setupWit
Page 140 and 141: total recallresettInG COntrOlsautom
Page 146 and 147: automationThis page is intentionall
Page 148 and 149: automation5-ivDuality se V3 Operato
Page 150 and 151:
automationThis page is intentionall
Page 152 and 153:
automationworking with projects and
Page 154 and 155:
Page 156 and 157:
automationCreating a new Mix passTo
Page 158 and 159:
automationMix runningPress play on
Page 160 and 161:
automationJoin and reviseAt any tim
Page 162 and 163:
automationprotection ModesEach comp
Page 164 and 165:
automationswitch automationPressing
Page 166 and 167:
automationtrim lokTrim Lok (only av
Page 168 and 169:
automationCopy and swapCopy and Swa
Page 170 and 171:
automationautomation setup OptionsT
Page 172 and 173:
automationTo set up MMC locates, se
Page 174 and 175:
Page 176 and 177:
automationsetup GuidelinesFor A-FAD
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
emoteThis page is intentionally alm
Page 184 and 185:
Page 186 and 187:
emoteConnecting Duality se to the C
Page 188 and 189:
emoteBacking up a projectTo create
Page 190 and 191:
emotetOtal reCall taBHere you can r
Page 192 and 193:
emoteexternals taBThis page allows
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Block DiagramsThis page is intentio
show all

Duality SE Operator's Manual - Solid State Logic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?