Duality SE Operator's Manual - Solid State Logic

More documents

Recommendations

Info

Console OperationsMonitor level Display and Calibrated listening levelThe ssl / Misc / setup menu provides two additional options:Monitor Gain Display: Music (Off to 11)Film (Off to 95dB)Gain (Off to 0dB)Monitor set Cal level is: 70 - 90Furthermore it is possible to change the Monitor Level pots resolution between ‘Fine’ and ‘Large’ in ‘Music’ or ‘Gain’modes by pushing down on the pot. The display above it will show which mode it is in. ‘Fine’ mode makes adjustments in0.1dB steps while ‘Large’ mode adjusts the value in 0.5dB steps.When working in ‘Film’ mode pushing down on the Level pot will adjust the monitor volume to the user defined calibratedlevel selected in the ssl / Misc / setup menu. Normal selection here would be the international recognized 85dB but itis possible to set a range from 70dB to 90dB. It is recommended that you use a SPL meter to calibrate your studiosmonitoring level to match that displayed on your Monitor Level display.Note that the monitor gain corresponding to +85dB SPL can be set in the Monitor options / CAL page 1 byadjusting the main monitor level control to give an SPL of 85dB, then pressing the 85dB switch.Note that if you make a change to this value in the Setup menu while running in Calibrated mode this change will not bereflected until you come out of Calibrated mode and re-enter it. You can tell which mode you have switched into as it willdisplay either ‘Cal’ for calibrated or ‘uCal’ for uncalibrated. Bear in mind that switching to a calibrated level of 85dB maycause a significant increase in listening volume so take care not to damage your hearing and of course your loudspeakermonitoring system.The third option setting ‘Gain’ allows a range of volume level settings where the maximum value is 0dB. All other valuesare reductions of this level through to ‘OFF’.2-30 Duality se V3 Operator’s Manual
Console OperationssOlO / aFl / pFlThe console’s default solo mode is a destructive solo-in-place — soloing a channel cuts all other channels. The alternativesolo modes — AFL, PFL and Solo-in-front are selected via the soft key display on the monitor control panel. Press theaFl/pFl button above the display to produce the following options:aFlpFlsIFIsOPressing a channel sOlO button routes the post channel pan signal, via the stereo AFL bus and the AFLlevel control, to the currently selected monitor speakers.Pressing a channel sOlO button routes a mono pre-fade signal, via the PFL bus and the PFL level control,to the left and right Main monitor speakers. Optionally, PFL signals may be fed to the Mini loudspeakers —see pFM in Monitor Options.(Solo-In-Front) Pressing a channel sOlO button routes a mix of the AFL signal and the selected left andright monitor sources to the monitor outputs. The SIF level control (select the sIF button to the right of themain monitor pot and use the pot to set the level) adjusts the balance between AFL signal and desk output.To solo isolate a number of channels, select IsO, press the sOlO buttons on all channels to be isolated,then deselect IsO. The SOLO switches on isolated channels will flash.Solo-isolated channels can be set to automatically solo in AFL mode via the Isolated channels AFL on solo:option in the SSL / Misc / Setup menu.altMOMMakes channel sOlO buttons intercancel with each other, so that soloing one channel will clear any othersolo selections.This option makes all the channel sOlO buttons momentary.Note that ALT and MOM do not affect the operation of centre section AFL and SOLO functionsSolo, AFL and PFL signals are all metered on the centre section sOlO meter. See Centre section Metering for moreinformation.When auditioning signals which are low in the mix, it is possible to boost the solo bus signal level by up to 10dB via the soloGain boost: option in the ssl / Misc / setup menu.Note that this boost is applied at the final output stage of the signal and is not reflected in the Solo meters. Ifinsufficient headroom is available, less gain will be applied.Duality se V3 Operator’s Manual2-31
Page 1: Solid State LogicS O U N D V I S I
Page 4 and 5: Manual ContentsFader Grouping 2-12F
Page 6 and 7: Manual ContentsWorking with DaW aut
Page 8 and 9: Manual ContentsseCtiOn 6: reMOte Br
Page 10 and 11: This page is intentionally almost b
Page 12 and 13: IntroductionThis page is intentiona
Page 14 and 15: IntroductionCreative Versatility•
Page 16 and 17: IntroductionThis page is intentiona
Page 20 and 21: Console OperationsThis page is inte
Page 22 and 23: Console OperationsSignal Processor
Page 24 and 25: Console Operationsan Introduction t
Page 26 and 27: Console OperationsAbove each bay of
Page 28 and 29: Console Operationsrel/HOlD — This
Page 30 and 31: Console OperationsChannel Output (C
Page 32 and 33: Console OperationsChannel panAt the
Page 34 and 35: Console OperationsMaster Channel Fa
Page 36 and 37: Console OperationsTo edit any exist
Page 38 and 39: Console Operations12342-16 Duality
Page 40 and 41: Console OperationsCentral routing p
Page 42 and 43: Console OperationsMain Output Funct
Page 44 and 45: Console OperationsMaster FaderThe m
Page 46 and 47: Console OperationsIf either MInI a
Page 48 and 49: Console OperationsMonitor OptionsA
Page 50 and 51: Console OperationsMonitor speaker C
Page 54 and 55: Console OperationsCue/Fx send Maste
Page 56 and 57: Console OperationsMisc OptionsA num
Page 58 and 59: Console OperationsThe following opt
Page 60 and 61: Console OperationsMix reassign Matr
Page 62 and 63: Console OperationsCentre section Me
Page 64 and 65: Console Operationssetup MenuThe cen
Page 66 and 67: Console OperationsDaw setupThe next
Page 70 and 71: DaWplug-In editor 3-33Plug-In Edito
Page 72 and 73: DaWThis page is intentionally almos
Page 74 and 75: DaWConsole FocusThe console can be
Page 78 and 79: DaWConnecting via physical MIDI por
Page 80 and 81: DaWsetting your workstation(s) to c
Page 82 and 83: DaWlogic pro 8When Logic is assigne
Page 88 and 89: DaWDaW utility Buttons (9)This grou
Page 92 and 93: DaWChannel solo and Cut panelsChann
Page 94 and 95: DaWselect ModeWith the sel button (
Page 100 and 101: DaWOther useful transport modesHalf
Page 102 and 103:
DaWselection Mode (Zoom/sel button
Page 104 and 105:
DaWThis page is intentionally almos
Page 106 and 107:
DaWselecting a DaW Channel for plug
Page 108 and 109:
DaWComparing your ChangesPressing t
Page 110 and 111:
DaWedit tools MenuEdit Tools (edts)
Page 112 and 113:
Page 114 and 115:
DaWautomation status DisplayPressin
Page 116 and 117:
Page 118 and 119:
DaWThe majority of DAW functions ar
Page 120 and 121:
DaWthe logic templateDuality SE emu
Page 122 and 123:
DaWnuendo/Cubase templateAs with ot
Page 124 and 125:
DaWDuality se’s nuendo Control sc
Page 126 and 127:
DaWCHannel is unchanged and assigns
Page 128 and 129:
DaWThe Transport Control buttons ar
Page 130 and 131:
This page is intentionally almost b
Page 132 and 133:
total recallThis page is intentiona
Page 134 and 135:
Page 136 and 137:
total recalltOtal reCall anD prOjeC
Page 138 and 139:
total recallrecalling a tr setupWit
Page 140 and 141:
total recallresettInG COntrOlsautom
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
automationThis page is intentionall
Page 148 and 149:
automation5-ivDuality se V3 Operato
Page 150 and 151:
Page 152 and 153:
automationworking with projects and
Page 154 and 155:
Page 156 and 157:
automationCreating a new Mix passTo
Page 158 and 159:
automationMix runningPress play on
Page 160 and 161:
automationJoin and reviseAt any tim
Page 162 and 163:
automationprotection ModesEach comp
Page 164 and 165:
automationswitch automationPressing
Page 166 and 167:
automationtrim lokTrim Lok (only av
Page 168 and 169:
automationCopy and swapCopy and Swa
Page 170 and 171:
automationautomation setup OptionsT
Page 172 and 173:
automationTo set up MMC locates, se
Page 174 and 175:
Page 176 and 177:
automationsetup GuidelinesFor A-FAD
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
emoteThis page is intentionally alm
Page 184 and 185:
Page 186 and 187:
emoteConnecting Duality se to the C
Page 188 and 189:
emoteBacking up a projectTo create
Page 190 and 191:
emotetOtal reCall taBHere you can r
Page 192 and 193:
emoteexternals taBThis page allows
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Block DiagramsThis page is intentio
show all

Duality SE Operator's Manual - Solid State Logic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?