Duality SE Operator's Manual - Solid State Logic

More documents

Recommendations

Info

automationMix runningPress play on the DAW to move forward. Check that timecode on the screen matches that of the DAW — if Duality SEis not reading MTC, it will not record any mix data.Note that when doing the first Mix Pass, it is important to start the Pass at the beginning of the song/track.As soon as the automation system has locked to the MIDI timecode (MTC), the mix status display will indicate ‘Mixrunning’. Simply operate the faders and switches to write your Mix as required, and the fader moves and switch data willbe recorded. The DAW may be toggled freely between Stop and Play – if Fast Forward is used or the DAW is locatedforward, the automation data will be extended to the new position when the DAW returns to Play.To abort the current Mix at any time, press the Discard soft key or the dedicated DIsCarD button in the‘AUTOMATION’ group above the ‘TRANSPORT’ buttons. To save the current Mix to flash memory and return to the MixList, press the end softkey or the dedicated enD button in the ‘AUTOMATION’ group. For more on the other buttonsin this group, see Dedicated automation Buttons.Mix reviewAt any time you can rewind the system, and as soon as the DAW is located to an earlier time and valid MTC or a MMClocate position command is received, the mix system enters ‘Mix Review’. All faders will switch to Replay status (all LEDsare off). This operation is known as a ‘rollback’.Mix running:Mix review:displayed while writing new automation datadisplayed when you replay previous automation dataThe number after Mix review (in this case 23) indicates the number of times you have rolled back in the current Mixand added new mix data. Playing through a section without writing data does not increment the rollback counter.When the DAW returns to Play, previously written automation data is replayed. Whilst in Mix review you may rollbackas many times as required to allow the Mix to be built up fader by fader. Each time a rollback takes place, and new mix dataentered, the rollback counter in the mix status display increments. Faders in Write at a rollback point will automaticallyswitch to Write when the system plays through the rollback point.5-10 Duality se V3 Operator’s Manual
automationDedicated automation ButtonsA group of dedicated automation buttons are provided in the centre section, just above the transport buttons:A double-press on the CanCel button cancels a Mix and returns you to the Mix List page. Pressing the enD buttonsaves the current Mix to flash memory and also returns you to the Mix List.Pressing the all replay button simply puts all faders and switches which are in Write into Replay status, which is usefulfor flipping all the currently recording controls into Replay without stopping or rewinding.The other buttons in this group are described on the following pages.Duality se V3 Operator’s Manual5-11
Page 1:
Solid State LogicS O U N D V I S I
Page 4 and 5:
Manual ContentsFader Grouping 2-12F
Page 6 and 7:
Manual ContentsWorking with DaW aut
Page 8 and 9:
Manual ContentsseCtiOn 6: reMOte Br
Page 10 and 11:
This page is intentionally almost b
Page 12 and 13:
IntroductionThis page is intentiona
Page 14 and 15:
IntroductionCreative Versatility•
Page 16 and 17:
IntroductionThis page is intentiona
Page 18 and 19:
Page 20 and 21:
Console OperationsThis page is inte
Page 22 and 23:
Console OperationsSignal Processor
Page 24 and 25:
Console Operationsan Introduction t
Page 26 and 27:
Console OperationsAbove each bay of
Page 28 and 29:
Console Operationsrel/HOlD — This
Page 30 and 31:
Console OperationsChannel Output (C
Page 32 and 33:
Console OperationsChannel panAt the
Page 34 and 35:
Console OperationsMaster Channel Fa
Page 36 and 37:
Console OperationsTo edit any exist
Page 38 and 39:
Console Operations12342-16 Duality
Page 40 and 41:
Console OperationsCentral routing p
Page 42 and 43:
Console OperationsMain Output Funct
Page 44 and 45:
Console OperationsMaster FaderThe m
Page 46 and 47:
Console OperationsIf either MInI a
Page 48 and 49:
Console OperationsMonitor OptionsA
Page 50 and 51:
Console OperationsMonitor speaker C
Page 52 and 53:
Console OperationsMonitor level Dis
Page 54 and 55:
Console OperationsCue/Fx send Maste
Page 56 and 57:
Console OperationsMisc OptionsA num
Page 58 and 59:
Console OperationsThe following opt
Page 60 and 61:
Console OperationsMix reassign Matr
Page 62 and 63:
Console OperationsCentre section Me
Page 64 and 65:
Console Operationssetup MenuThe cen
Page 66 and 67:
Console OperationsDaw setupThe next
Page 68 and 69:
Page 70 and 71:
DaWplug-In editor 3-33Plug-In Edito
Page 72 and 73:
DaWThis page is intentionally almos
Page 74 and 75:
DaWConsole FocusThe console can be
Page 76 and 77:
Page 78 and 79:
DaWConnecting via physical MIDI por
Page 80 and 81:
DaWsetting your workstation(s) to c
Page 82 and 83:
DaWlogic pro 8When Logic is assigne
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
DaWDaW utility Buttons (9)This grou
Page 90 and 91:
Page 92 and 93:
DaWChannel solo and Cut panelsChann
Page 94 and 95:
DaWselect ModeWith the sel button (
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
DaWOther useful transport modesHalf
Page 102 and 103:
DaWselection Mode (Zoom/sel button
Page 104 and 105:
Page 106 and 107:
DaWselecting a DaW Channel for plug
Page 108 and 109: DaWComparing your ChangesPressing t
Page 110 and 111: DaWedit tools MenuEdit Tools (edts)
Page 112 and 113: DaWThis page is intentionally almos
Page 114 and 115: DaWautomation status DisplayPressin
Page 116 and 117: DaWThis page is intentionally almos
Page 118 and 119: DaWThe majority of DAW functions ar
Page 120 and 121: DaWthe logic templateDuality SE emu
Page 122 and 123: DaWnuendo/Cubase templateAs with ot
Page 124 and 125: DaWDuality se’s nuendo Control sc
Page 126 and 127: DaWCHannel is unchanged and assigns
Page 128 and 129: DaWThe Transport Control buttons ar
Page 130 and 131: This page is intentionally almost b
Page 132 and 133: total recallThis page is intentiona
Page 136 and 137: total recalltOtal reCall anD prOjeC
Page 138 and 139: total recallrecalling a tr setupWit
Page 140 and 141: total recallresettInG COntrOlsautom
Page 146 and 147: automationThis page is intentionall
Page 148 and 149: automation5-ivDuality se V3 Operato
Page 152 and 153: automationworking with projects and
Page 156 and 157: automationCreating a new Mix passTo
Page 160 and 161: automationJoin and reviseAt any tim
Page 162 and 163: automationprotection ModesEach comp
Page 164 and 165: automationswitch automationPressing
Page 166 and 167: automationtrim lokTrim Lok (only av
Page 168 and 169: automationCopy and swapCopy and Swa
Page 170 and 171: automationautomation setup OptionsT
Page 172 and 173: automationTo set up MMC locates, se
Page 176 and 177: automationsetup GuidelinesFor A-FAD
Page 182 and 183: emoteThis page is intentionally alm
Page 186 and 187: emoteConnecting Duality se to the C
Page 188 and 189: emoteBacking up a projectTo create
Page 190 and 191: emotetOtal reCall taBHere you can r
Page 192 and 193: emoteexternals taBThis page allows
Page 198 and 199: Block DiagramsThis page is intentio
show all

Duality SE Operator's Manual - Solid State Logic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?