Lists 11/2003 Edition

11.03 3 Variables3.7 Tool and magazine datacuttEdgeParam$TC_DPCEx[y,z] x = ParamNo y = ToolNo z = EdgeNoOffset value parameter and edge list with D numbers for a tool1st section: Offset value parameter for a tool edge:The meaning of each parameter depends on the tool type. At present 25 parameters are reserved for each tool edge(however only some of them are used). To be flexible for future extensions use the variable 'numCuttEdgeParams'rather than the fixed number 25 for the number of parameters.A detailed description of tool parameters can be found in the documentation 'Tool Offset (W1)', Section "Tool edge".The following list is a summary of the tool edge parameters:Parameter 1: Geometry -- tool type ($TC_DP1)Parameter 2: Geometry -- tool point direction ($TC_DP2)Parameter 3: Geometry -- length 1 ($TC_DP3)Parameter 4: Geometry -- length 2 ($TC_DP4)Parameter 5: Geometry -- length 3 ($TC_DP5)Parameter 6: Geometry -- radius ($TC_DP6)Parameter 7: Geometry -- corner radius (tool type 700; slotting saw) ($TC_DP7)Parameter 8: Geometry -- length 4 (tool type 700; slotting saw) ($TC_DP8)Parameter 9: Geometry -- length 5 ($TC_DP9)Parameter 10: Geometry -- angle 1 ($TC_DP10)Parameter 11: Geometry -- angle 2 for tapered milling tools ($TC_DP11)Parameter 12: Wear -- length 1 ($TC_DP12)Parameter 13: Wear -- length 2 ($TC_DP13)Parameter 14: Wear -- length 3 ($TC_DP14)Parameter 15: Wear -- radius ($TC_DP15)Parameter 16: Wear -- slot width b / rounding radius ($TC_DP16)Parameter 17: Wear -- proj. length k ($TC_DP17)Parameter 18: Wear -- length 5 ($TC_DP18)Parameter 19: Wear -- angle 1 ($TC_DP19)Parameter 20: Wear -- angle 2 for tapered milling tools ($TC_DP20)Parameter 21: Adapter -- length 1 ($TC_DP21)Parameter 22: Adapter -- length 2 ($TC_DP22)Parameter 23: Adapter -- length 3 ($TC_DP23)Parameter 24: Relief angle ($TC_DP24)Parameter 25: Manual Turn: Cutting rate ($TC_DP25)Shopmill: Bit-coded value for different states of tools of type 1xx and 2xx ($TC_DP25)All parameters up to 25, that are not listed, are reserved.2nd section: edgeDNo (SW 5.1 and later), associated optional D numbers of edges:-1: No edge1 .. maxDNo: Edge exists, associated D number, only when "any D numbers" function is activated(maxnumCuttEdges_Tool < maxCuttingEdgeNo)Edge No.: 1 to maxnumCuttEdges_Tool, when edge exists, but when "Assignment of any D numbers" function is notactivated on the NC.0: No D number assigned/assignment cancelled. (In this case, OPI deviates from NCK variable$TC_DPCE....$TC_DPCE = edge number, D = offset number D.If the D number of an edge (variable of module TO) has been set to invalid, the value $TC_DPCE remains unaffected.The edge number specified in the description of the row index matches parameter $TC_DPCE.The variable D No. defined in the module matches the second index in the offset-specific parameters of type$TC_DPx[T,D],... and others; with x=1,....25.).Important: This variable is called "edgeData" in the MMC102.The value for the tool type is stored internally as an integer.- 0 DoubleMulti-line: yesFor edge offset value parameters:(edgeNo - 1) *numCuttEdgeParams +ParameterNoFor D numbers:((numCuttEdgeParams *maxnumCuttEdges_Tool) +EdgeNo)(numCuttEdgeParams + 1) *maxnumCuttEdges_Tool© Siemens AG, 2003. All rights reservedSINUMERIK 840D/840Di/810D SIMODRIVE 611 digital Lists (LIS) – 11.03 Edition 3-527