Lists 11/2003 Edition

11.03 I IndexplaceData .................................................... 3-545placeType .................................................... 3-547Plane assignment of protection zone ....3-362, 3-370Plane setting ................................................ 3-433PLC messages (DB2) .................................... 4-625PLC_ALARM_PICTUREMD 9055 .................................................. 2-159PLC_CYCLE_TIME_AVERAGEMD 10110................................................. 2-196PLC_CYCLIC_TIMEOUTMD 10100................................................. 2-196PLC_HOTKEYMD 9017 .................................................. 2-158PLC_RUNNINGUP_TIMEOUTMD 10120................................................. 2-196PLC_SYMBOL_FILTERMD 9054 .................................................. 2-159PLC_SYMBOL_SORTMD 9053 .................................................. 2-159PLCIO_IN_UPDATE_TIMEMD 10398................................................. 2-202PLCIO_LOGIC_ADDRESS_INMD 10395................................................. 2-202PLCIO_LOGIC_ADDRESS_OUTMD 10397................................................. 2-202PLCIO_NUM_BYTES_INMD 10394................................................. 2-201PLCIO_NUM_BYTES_OUTMD 10396................................................. 2-202PLCIO_TYPE_REPRESENTATIONMD 10399................................................. 2-202plcStartReason ..................................3-465, 3-468pMthSDC ..................................................... 3-447PO_WITHOUT_POLYMD 10674................................................. 2-206pOffn........................................................... 3-447POLE_ORI_MODEMD 21108................................................. 2-248POLE_PAIR_PITCHMD 1170 .................................................... 2-87Pos. offset of the synchr. spindle desiredvalue...........................................3-397, 3-481POS_AX_VELOMD 32060................................................. 2-287POS_DRIVE_SPEED_LIMITMD 5440 .................................................. 2-149POS_DUAL_GAIN_COMP_FLOWMD 5464 .................................................. 2-149POS_DUAL_GAIN_COMP_S_FLOWMD 5485 .................................................. 2-150POS_DUAL_GAIN_COMP_S_VOLTMD 5486 .................................................. 2-150POS_DUAL_GAIN_COMP_VOLTAGEMD 5465 .................................................. 2-149POS_DUAL_GAIN_COMP_Z_FLOWMD 5480 .................................................. 2-150POS_DUAL_GAIN_COMP_Z_VOLTMD 5481 .................................................. 2-150POS_LIMIT_MINUSMD 36100................................................. 2-300POS_LIMIT_MINUS2MD 36120................................................. 2-300POS_LIMIT_PLUSMD 36110 .................................................2-300POS_LIMIT_PLUS2MD 36130 .................................................2-300POS_TAB_SCALING_SYSTEMMD 10270 .................................................2-198POSCTRL_CYCLE_DELAYMD 10062 .................................................2-193POSCTRL_CYCLE_TIMEMD 10061 .................................................2-193POSCTRL_DAMPINGMD 32950 .................................................2-293POSCTRL_DESVAL_DELAYMD 10065 .................................................2-193POSCTRL_DESVAL_DELAY_INFOMD 32990 .................................................2-293POSCTRL_GAINMD 32200 .................................................2-288POSCTRL_INTEGR_ENABLEMD 32220 .................................................2-288POSCTRL_INTEGR_TIMEMD 32210 .................................................2-288POSCTRL_OUT_FILTER_ENABLEMD 32930 .................................................2-293POSCTRL_OUT_FILTER_TIMEMD 32940 .................................................2-293POSCTRL_SYSCLOCK_TIME_RATIOMD 10060 .................................................2-193POSCTRL_ZERO_ZONEMD 32960 .................................................2-293Position as diameter or radius value.................3-507Position component X ....................................3-568Position component Y ....................................3-569Position component Z.....................................3-569Position control cycle factor.............................3-584Position control gain factor.................. 3-409, 3-493Position controller difference ............... 3-415, 3-499Position of the cutting edge center point............3-501Position of tool base, desired value ..................3-501Position offset from synchronous actions .........3-400,3-484Position offset referring to leading axis/spindle........................................ 3-404, 3-488POSITION_LSBMD 5714...................................................2-154POSITIONING_TIMEMD 36020 .................................................2-299Power section code of drive module .................3-584POWER_DISABLE_DELAYMD 5404...................................................2-148POWER_ENABLE_DELAYMD 5532...................................................2-151POWER_FACTOR_COS_PHIMD 1129.....................................................2-83POWER_FACTOR_COS_PHI_M2MD 2129...................................................2-136POWER_LIMIT_1MD 1235.....................................................2-96POWER_LIMIT_1_M2MD 2235...................................................2-138POWER_LIMIT_2MD 1236.....................................................2-96POWER_LIMIT_2_M2MD 2236...................................................2-138© Siemens AG, 2003. All rights reservedSINUMERIK 840D/840Di/810D SIMODRIVE 611 digital Lists (LIS) – 11.03 Edition I-737