Lists 11/2003 Edition

11.03 I IndexCorr. to circleCenter for block search withcalc........................................................ 3-459CORR_VELOMD 32070................................................. 2-287corrBlActive.................................................. 3-444Corresp. to actNumber for block search withcalc........................................................ 3-438Corresponds to $actToolBasPosEN................. 3-506Corresponds to circleCenterWos..................... 3-460Corresponds to circleRadiusWos..................... 3-460countActivated.............................................. 3-611Counter for NC-start key ................................ 3-446Counter incremented with each call ofEXTCALL ............................................... 3-377Counter indicating changes of axesconfiguration........................................... 3-443Counter indicating that a new LUD ACC isavailable................................................. 3-445COUPLE_AXIS_1MD 21300................................................. 2-250COUPLE_BLOCK_CHANGE_CTRL_1MD 21320................................................. 2-251COUPLE_IS_WRITE_PROT_1MD 21340................................................. 2-251COUPLE_POS_TOL_COARSEMD 37200................................................. 2-312COUPLE_POS_TOL_FINEMD 37210................................................. 2-312COUPLE_RATIO_1MD 42300................................................. 2-320COUPLE_RESET_MODE_1MD 21330................................................. 2-251COUPLE_VELO_TOL_COARSEMD 37220................................................. 2-312COUPLE_VELO_TOL_FINEMD 37230................................................. 2-312COUPLING_MODE_1MD 21310................................................. 2-251cOut ............................................................ 3-444CPREC_WITH_FFWMD 20470................................................. 2-243CRC diagnostic parameter ............................. 3-524CRC errors on the drive bus ................3-406, 3-490CRC_DIAGNOSISMD 1720 .................................................. 2-130CRC_DIAGNOSISMD 5720 .................................................. 2-154crcErrorCount ....................................3-521, 3-524CRC-parameter for diagnosis ......................... 3-521CRIT_SPLINE_ANGLEMD 42470................................................. 2-322CTAB_DEFAULT_MEMORY_TYPEMD 20905................................................. 2-246CTAB_ENABLE_NO_LEADMOTIONMD 20900................................................. 2-246CTM_ANGLE_REFERENCE_AXISMD 9632 .................................................. 2-176CTM_CIRC_TAP_DWELL_TIME_1MD 9644 .................................................. 2-177CTM_CIRC_TAP_DWELL_TIME_2MD 9645 .................................................. 2-177CTM_COUNT_GEAR_STEPSMD 9627 .................................................. 2-176CTM_CROSS_AX_DIAMETER_ONMD 9611...................................................2-174CTM_CUSTOMER_START_PICTUREMD 9625...................................................2-175CTM_CYC_ROUGH_BLANC_OFFSMD 9552...................................................2-172CTM_CYC_ROUGH_MIN_REST_MAT1MD 9554...................................................2-172CTM_CYC_ROUGH_MIN_REST_MAT2MD 9555...................................................2-172CTM_CYC_ROUGH_RELEASE_ANGLEMD 9551...................................................2-172CTM_CYC_ROUGH_RELEASE_DISTMD 9550...................................................2-172CTM_CYC_ROUGH_TRACE_ANGLEMD 9553...................................................2-172CTM_CYC_ROUGH_VAR_DEPTHMD 9556...................................................2-172CTM_CYCLE_DWELL_TIMEMD 9621...................................................2-175CTM_CYCLE_DWELL_TIME_SECMD 9631...................................................2-176CTM_CYCLE_SAFETY_CLEARANCEMD 9620...................................................2-175CTM_ENABLE_C_AXISMD 9618...................................................2-175CTM_ENABLE_CALC_THREAD_PITCMD 9640...................................................2-177CTM_ENABLE_CIRCLE_HOLE_CYCLMD 9642...................................................2-177CTM_ENABLE_DRIVEN_TOOLMD 9643...................................................2-177CTM_ENABLE_FEED_P_MINMD 9608...................................................2-174CTM_ENABLE_G_CODE_INPUTMD 9641...................................................2-177CTM_ENABLE_RAPID_FEEDMD 9607...................................................2-174CTM_ENABLE_REFPOINTMD 9622...................................................2-175CTM_ENABLE_S_TOOL_TABLEMD 9636...................................................2-176CTM_FACTOR_I_CALC_THR_PITCHMD 9647...................................................2-177CTM_FACTOR_O_CALC_THR_PITCHMD 9646...................................................2-177CTM_FIN_FEED_PERCENTMD 9630...................................................2-176CTM_G91_DIAMETER_ONMD 9619...................................................2-175CTM_INC_DEC_FEED_PER_MINMD 9633...................................................2-176CTM_INC_DEC_FEED_PER_ROTMD 9634...................................................2-176CTM_MAX_INP_FEED_P_MINMD 9637...................................................2-176CTM_MAX_INP_FEED_P_ROTMD 9638...................................................2-177CTM_MAX_TOOL_WEARMD 9639...................................................2-177CTM_MODE_SELECT_BY_SOFTKEYMD 9624...................................................2-175CTM_OPTION_MASKMD 9599...................................................2-173© Siemens AG, 2003. All rights reservedSINUMERIK 840D/840Di/810D SIMODRIVE 611 digital Lists (LIS) – 11.03 Edition I-711