Lists 11/2003 Edition

I Index 11.03SERVO_DISABLE_DELAY_TIMEMD 36620................................................. 2-301servoDataFl32 .............................................. 3-593servoDataFl64 .............................................. 3-593Set of blocks from the current operation ........... 3-458SETINT_ASSIGN_FASTINMD 21210................................................. 2-250Setpoint assignment ...................................... 3-585Setpoint cutting angle .................................... 3-433Setpoint of axis-specific feedrate, .................... 3-404Setpoint workpiece position angle ................... 3-436Settable value for INC_VAR .....3-396, 3-480, 3-502Settings for NCK tool management.................. 3-345Set-up mode......................................3-407, 3-491setupTime.................................................... 3-605SHOW_CHANNEL_SPANNING_STATEMD 9052 .................................................. 2-159siemData ...............................3-578, 3-579, 3-582siemEdgeData.............................................. 3-580Siemens appl. tool cutting edge parameter ....... 3-580Siemens application magazine data......3-579, 3-581Siemens application monitoring data................ 3-582Siemens application tool parameter ................. 3-578siemPlaceData ............................................. 3-581Signal from cycle to PLC................................ 3-444Signal from PLC to cycle................................ 3-443Signals of the PLC application interface ........... 4-617Signals to axis/spindle (PLC NCK)............... 4-669Signals to/from NCK channel (DB 21 -28)......... 4-651Sign-of-life error counter encoder 1.................. 3-596Sign-of-life error counter encoder 2.................. 3-596Sign-of-life error counter output....................... 3-595simo611dSupport.......................................... 3-351SIMU_AX_VDI_OUTPUTMD 30350................................................. 2-282Simulated lead value - position.............3-399, 3-483Simulated leading value velocity...........3-399, 3-483Single axis status ...............................3-401, 3-485Single block.................................................. 3-456Single block mode......................................... 3-456Single block read in quasi-stop state................ 3-461singleBlock................................................... 3-461SINGLEBLOCK2_STOPREMD 42200................................................. 2-320singleBlockActive .......................................... 3-456singleBlockType............................................ 3-456SI-PowerOn-Alarms Reset-acknowledgeable.... 3-496Size downwards in half locations..................... 3-530Size of DRAM file system no. 1....................... 3-386Size of DRAM file system no. 2....................... 3-386Size of NCK alarm buffer................................ 3-345Size of SRAM file system ............................... 3-387Size to the left in half locations........................ 3-530Size to the right in half locations...................... 3-530Size upwards in half locations......................... 3-530Skip............................................................. 3-612Skip level /0.................................................. 3-456Skip level /1.................................................. 3-456Skip level /2.................................................. 3-456Skip level /3.................................................. 3-456Skip level /4.................................................. 3-456Skip level /5.................................................. 3-456Skip level /6 ..................................................3-457Skip level /7 ..................................................3-457Skip level /8 ..................................................3-457Skip level /9 ..................................................3-457skipLevel0Active............................................3-456skipLevel1Active............................................3-456skipLevel2Active............................................3-456skipLevel3Active............................................3-456skipLevel4Active............................................3-456skipLevel5Active............................................3-456skipLevel6Active............................................3-457skipLevel7Active............................................3-457skipLevel8Active............................................3-457skipLevel9Active............................................3-457SLASH_MASKMD 10706 .................................................2-207Slave active on bus or not (LED green).............3-600Slave data are available .................................3-599Slot information is available.............................3-602Slot number within the slave............................3-602SMOOTH_CONTUR_TOLMD 42465 .................................................2-321SMOOTH_ORI_TOLMD 42466 .................................................2-321SMOOTH_RUN_DIAGNOSISMD 1724...................................................2-131SMOOTH_RUN_TOLMD 1615...................................................2-122Smoothing the desired value of the rotary speed.........3-407, 3-491SMOOTHING_MODEMD 20480 .................................................2-243SOFT_ACCEL_FACTORMD 32433 .................................................2-289Software end position, negative direction .........3-401,3-485Software end position, positive direction ..........3-401,3-485Source location number new tool .....................3-442Source location number old tool.......................3-442Source magazine new tool..............................3-442Source magazine old tool ...............................3-442Source of the lead value ..................... 3-399, 3-483SPDCTRL_INTEGR_TIME_1_AMMD 1453...................................................2-113SPDCTRL_INTEGR_TIME_1_AM_M2MD 2453...................................................2-140spec...................................... 3-414, 3-498, 3-508specParts .....................................................3-449Speed setpoint ..............................................3-404Speed, setpoint .............................................3-524SPEED_CRTL_DISABLE_STOPTIMEMD 5402...................................................2-148SPEED_DES_EQ_ACT_DELAYMD 1427...................................................2-112SPEED_DES_EQ_ACT_TOLMD 1426...................................................2-112SPEED_DES_EQ_ACT_TOL_M2MD 2426...................................................2-140SPEED_FFW_DELAYMD 1425...................................................2-111SPEED_FFW_FILTER_TIMEMD 1424...................................................2-111© Siemens AG, 2003. All rights reservedI-744 SINUMERIK 840D/840Di/810D SIMODRIVE 611 digital Lists (LIS) – 11.03 Edition