Lists 11/2003 Edition

I Index 11.03Number of Siemens application magazine data. 3-349Number of Siemens application tool data.......... 3-351Number of slaves connected to bus ................. 3-598Number of slots............................................. 3-601Number of slots per axis container................... 3-348Number of special workpieces (user-defined).... 3-449Number of spindles ....................................... 3-355Number of strokes......................................... 3-475Number of synchronous actions ...........3-470, 3-472Number of T area.......................................... 3-356Number of T areas ........................................ 3-350Number of the active M-function...................... 3-470Number of the actual drive parameter set ........ 3-405,3-489Number of the geometry axis .......................... 3-508Number of the internal load magazine.............. 3-538Number of the magazine.....................3-541, 3-543Number of the preselected T-function .............. 3-470Number of tool edges .................................... 3-355Number of toolholder ..................................... 3-443Number of toolholders in TOA of channels........ 3-446Number of tools in the area TO ....................... 3-548Number of user frames .................................. 3-355Number of valid contour elements ........3-361, 3-368Number of workpieces machined in current run. 3-440numChannels ............................................... 3-348numContainer............................................... 3-348numContainerSlots........................................ 3-348numContourInProtArea .................................. 3-354numCuttEdgeParams .................................... 3-348numCuttEdgeParams_tao .............................. 3-348numCuttEdgeParams_tas .............................. 3-348numCuttEdgeParams_ts ................................ 3-348numCuttEdgeParams_tu................................ 3-348numCuttEdgeParams_tus .............................. 3-348numCuttEdges...................................3-529, 3-548numData...................................................... 3-608numDigitInp.................................................. 3-349numDigitOutp ............................................... 3-349numDrives.................................................... 3-349numElementsFastFifoTooSmall ...................... 3-612numFilesPerDir............................................. 3-378numGCodeGroups ........................................ 3-349numGCodeGroupsFanuc ............................... 3-349numGeoAxes................................................ 3-354numGlobMachAxes ....................................... 3-349numHandWheels .......................................... 3-349numMachAxes.............................................. 3-355numMagLocParams_tap ................................ 3-349numMagLocParams_u................................... 3-349numMagParams_tam .................................... 3-349numMagParams_u........................................ 3-350numMagPlaceParams.................................... 3-350numMagPlacesMax....................................... 3-350numMagsMax............................................... 3-350numOriAxes ................................................. 3-355numParams_Adapt........................................ 3-350numParams_SC ........................................... 3-350numPlaceMulti.............................................. 3-350numPlaceMultiParams ................................... 3-350numProtArea ................................................ 3-355numRParams................................................3-355numSpindles.................................................3-355numSpindlesLog............................................3-355numStrokes ..................................................3-475numSubDirsPerDir.........................................3-378numSynAct ....................................... 3-470, 3-472numToBaust .................................................3-350numToolEdges..............................................3-355numToolHolderParams...................................3-350numToolHolders ............................................3-446numToolParams_tad......................................3-351numToolParams_tu........................................3-351numTools .....................................................3-548numTraceProtocDataList ................................3-378numTraceProtocEventType.............................3-446numTraceProtocOemDataList .........................3-378numTraceProtocOemEventType......................3-446numUserFrames................................ 3-351, 3-355NUTATION_ANGLE_NAMEMD 10648 .................................................2-205OOdinate arc centre of 3rd contour element.........3-365Odinate end point of 3rd contour element..........3-367OEM text for logging buffer .............................3-355oemProtText .................................................3-355Offset Hirth tooth system 1st axis.....................3-567Offset Hirth tooth system 2nd axis....................3-567Offset memory number length (Fanuc) .............3-439Offset memory number radius (ISO Dialect)) .....3-438Offset normal ................................................3-447Offset of 1st rotary axis in degrees...................3-566Offset of 2nd rotary axis in degrees..................3-567Offset to leading axis/spindle, actual value ......3-402,3-486OFFSET_COMPENSATIONMD 5470...................................................2-150OFFSETVALUE_FOR_MONITORINGMD 31510 .................................................2-286ONLINE_CUTCOM_ENABLEMD 20254 .................................................2-240Operating mode................................. 3-522, 3-525OPERATING_MODEMD 1730...................................................2-132OPERATING_MODEMD 5730...................................................2-155OPERATING_MODE_DEFAULTMD 10720 .................................................2-208operatingMode .................................. 3-522, 3-525operatingTime...............................................3-607opMode...........3-418, 3-420, 3-426, 3-510, 3-514OPT_LOAD_ANGELMD 1128.....................................................2-83optAssStopActive ..........................................3-455optStopActive................................................3-455Ordinal number of an alarm...... 3-389, 3-391, 3-393Ordinate arc centre of 10th contour element.....3-359,3-366Ordinate arc centre of 1st contour element.......3-358,3-365© Siemens AG, 2003. All rights reservedI-734 SINUMERIK 840D/840Di/810D SIMODRIVE 611 digital Lists (LIS) – 11.03 Edition