Barrel Heaters - Hasmak.com.tr

15.9 mm(0.625 in.)<strong>Heaters</strong>Mica StripApplications andTechnical DataType 1—Opposite EndsBHeated AreaType 2—Tandem15.9 mm(0.625 in.)BCBHeated AreaType 3—Parallel Made-to-Order15.9 mm(0.625 in.)BHeated AreaA15.9 mm(0.625 in.)A9.5 mm(0.375 in.)A9.5 mm(0.375 in.)Type 4—Opposite Ends with HolesPhysical Limitations of Lead VariationsWidthLengthHeater Type Minimum Maximum Minimum Maximummm (in.) mm (in.) mm (in.) mm (in.)Post TerminalType 1 - Opposite ends 15.8 ( 5 ⁄8) 381 (15) 50.8 (2) 2438.4 (96 1 )Type 2 - Tandem 15.8 ( 5 ⁄8) 381 (15) 50.8 (2) 2438.4 (96 1 )Type 3 - Parallel 38.1 (1 1 ⁄2) 381 (15) 50.8 (2) 2438.4 (96 1 )Type 4 - Opposite endswith holes 15.8 ( 5 ⁄8) 381 (15) 139.7 (5 1 ⁄2) 2438.4 (96 1 )Type 5 - Tandem with holes 15.8 ( 5 ⁄8) 381 (15) 139.7 (5 1 ⁄2) 2438.4 (96 1 )Type 6 - Parallel with holes 38.1 (1 1 ⁄2) 381 (15) 139.7 (5 1 ⁄2) 2438.4 (96 1 )LeadsType C, E. F, H 25.4 (1) 381 (15) 139.7 (5 1 ⁄2) 2438.4 (96 1 )Type Kwithout mounting holes 25.4 (1) 381 (15) 139.7 (5 1 ⁄2) 2438.4 (96 1 )with mounting holes 38.1 (1 1 ⁄2) 381 (15) 139.7 (5 1 ⁄2) 2438.4 (96 1 )European PlugVertical 25.4 (1) 381 (15) 139.7 (5 1 ⁄2) 2438.4 (96 1 )Horizontal 63.5 (2 1 ⁄2) 381 (15) 159 (6 1 ⁄4) 2438.4 (96 1 )Three-Phase 76.2 (3) 381 (15) 139.7 (5 1 ⁄2) 2438.4 (96 1 )Dual Voltage 76.2 (3) 381 (15) 139.7 (5 1 ⁄2) 2438.4 (96 1 )Terminal Box 2Type 2 - Tandem 38.1 (1 1 ⁄2) 381 (15) 108 (4 1 ⁄4) 2438.4 (96 1 )Type 3 - Parallel 63.5 (2 1 ⁄2) 381 (15) 108 (4 1 ⁄4) 2438.4 (96 1 )Type 5 - Tandem with holes 38.1 (1 1 ⁄2) 381 (15) 159 (6 1 ⁄4) 2438.4 (96 1 )Type 6 - Parallel with holes 63.5 (2 1 ⁄2) 381 (15) 159 (6 1 ⁄4) 2438.4 (96 1 )➀ Consult the factory if you need to exceed 2438.4 mm (96 in.).➁ Not available on stock heaters.Note: Some <strong>com</strong>binations of maximum and minimums cannot occur on the same heater.44.5 mm(1.75 in.)44.5 mm(1.75 in.)Heated AreaBCHeated AreaBC44.5 mm(1.75 in.)Type 5—Tandem with HolesType 6—Parallel with HolesAA25.4 mm(1 in.)TerminationsTypes 1 through 6, as illustrated,show the placement of terminals forWatlow mica strip heaters. However,please note Type 3 terminals are notavailable on stock units. Placement isspecified in terms of length, width andcenter-to-center dimensions. Thesedimensions are as follows:Length:Tolerance: ±1.6 mm (0.06 in.)Width:Tolerance: ±1.6 mm (0.06 in.)Thickness:Nominal: 4.7 mm (0.19 in.)Types 4, 5 and 6 have 9.5 mm x6.3 mm (0.38 in. x 0.25 in.) mountingslots. Letters A, B and C, calledout in the illustrations, denote thefollowing:A = width, B = overall length andC = center-to-center dimensions onmounting slots.A44.5 mm(1.75 in.)Heated Area25.4 mm(1 in.)Specify Type when ordering.318