Barrel Heaters - Hasmak.com.tr

Hot RunnerNozzle <strong>Heaters</strong>FIREROD CartridgeLA StockMounting OptionsStandard Fitting LocationOptional Fitting LocationFitting overlaps the unheated section and issoldered to the sheath.A**BLA StockThreaded FittingsThreaded fittings allow for fast,water-tight installation of the heaterinto a threaded hole. These fittingscan be ordered in either brass or304 stainless steel. Other stainlesssteel alloys are available uponLeadArrangementCrimped LeadsSwaged in LeadsSTR SS HoseSTR SS BraidTeflon ® Seal & LDSSilicone Seal & LDSSTD Fitting aLocationDimension Amm (in.)6 ( 1 ⁄4)8 ( 5 ⁄16 bd )13 ( 1 ⁄4 c )13 ( 1 ⁄4)22 ( 7 ⁄8)22 ( 7 ⁄8)request. Double threaded fittings arealso available.To order, specify either brass orstainless steel threaded fittings.On LA stock give location of fittings,if no-heat extension option isrequested. Specify location fromdisc end to bottom of threads.a The location of the threaded fitting fromthread end of fitting to the lead end ofheater.All optional fitting locations are availableonly with LA Stock no-heat extensions.Consult the Watlow factory in St. Louis,Missouri, for details.b On 6 mm (0.25 in.) diameter FIREROD only“A” dimension is 11 mm (0.4375 in.).c On 6 mm (0.25 in.) diameter FIREROD only“A” dimension is 16 mm (0.625 in.).d On 16 mm (0.625 in.) and 19 mm (0.75 in.)the fitting is located at 22 mm (0.875 in.)from lead end using a 16 mm (0.75 in.)no-heat extension. In order to locate at8 mm (0.3125 in.) the fitting must beepoxied.1.6 mm (0.0625 in.)**HCDFlangesStainless steel flanges are aconvenient mounting method as wellas a way to position a heater within anapplication. The standard flange isstaked on and located 6 mm (0.25in.) from the LE. The flange can belocated up to 57 mm (2.25 in.) fromthe LE as long as it is over a no-heatsection. Use this option in <strong>com</strong>binationwith most LA configurations.To order, specify flange, size andlocations.Flange SpecificationsFIRERODinchesDiameter Flangeinches Size D C H1⁄4, 3 ⁄8, 1 ⁄2 FS 1 3⁄4 0.1441⁄4, 3 ⁄8, 1 ⁄25⁄8, 3 ⁄4FM 1 1 ⁄2 1 1 ⁄8 0.1565⁄8, 3 ⁄4, 1 FL 2 1 1 ⁄2 0.2013.6 mm (0.140 in.)Locating RingA stainless steel locating ring can beused as a retaining collar to positiona FIREROD if mounting requirementsare not critical.On LA Stock, give location if the noheatextension option is requested.On in-stock FIRERODs without anLA option, location will be on thelast 6 mm (0.25 in.). To order,specify locating ring.Locating Ring SpecificationsMinimum No-Heat RequiredinchesDiameter3 1 5⁄8 ⁄2 ⁄8Ring O.D.5⁄83⁄43⁄47⁄8 182