BSIM3v3.2.2 MOSFET Model - The University of Texas at Dallas

More documents

Recommendations

Info

Extraction Strategiesdevice performance quite well. Values extracted in this manner will now havesome physical relevance.6.2 Extraction StrategiesTwo different strategies are available for extracting parameters: the single deviceextraction strategy and group device extraction strategy. In single deviceextraction strategy, experimental data from a single device is used to extract acomplete set of model parameters. This strategy will fit one device very well butwill not fit other devices with different geometries. Furthermore, single deviceextraction strategy can not guarantee that the extracted parameters are physical. Ifonly one set of channel length and width is used, parameters related to channellength and channel width dependencies can not be determined.BSIM3v3 uses group device extraction strategy. This requires measured data fromdevices with different geometries. All devices are measured under the same biasconditions. The resulting fit might not be absolutely perfect for any single devicebut will be better for the group of devices under consideration.6.3 Extraction Procedure6.3.1 Parameter Extraction RequirementsOne large size device and two sets of smaller-sized devices are needed toextract parameters, as shown in Figure 6-1.6-2 BSIM3v3.2.2 Manual Copyright © 1999 UC Berkeley
Extraction ProcedureWOrthogonal Set of W and LW minL minLarge W and LLFigure 6-1. Device geometries used for parameter extractionThe large-sized device (W ≥ 10µm, L ≥ 10µm) is used to extractparameters which are independent of short/narrow channel effects andparasitic resistance. Specifically, these are: mobility, the large-sized devicethreshold voltage V Tideal , and the body effect coefficients K 1 and K 2 whichdepend on the vertical doping concentration distribution. The set of deviceswith a fixed large channel width but different channel lengths are used toextract parameters which are related to the short channel effects. Similarly,the set of devices with a fixed, long channel length but different channelwidths are used to extract parameters which are related to narrow widthBSIM3v3.2.2 Manual Copyright © 1999 UC Berkeley 6-3
Page 1 and 2:
BSIM3v3.2.2 MOSFET ModelUsers’ Ma
Page 5 and 6:
Table of ContentsCHAPTER 1: Introdu
Page 7 and 8:
CHAPTER 6: Parameter Extraction 6-1
Page 9 and 10:
APPENDIX C: References C-1APPENDIX
Page 11 and 12:
CHAPTER 1: Introduction1.1 General
Page 14 and 15:
Non-Uniform Doping and Small Channe
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Mobility Modelµeffµ=01 + ( E E )e
Page 30 and 31:
Bulk Charge Effectµ eff Ev = , E <
Page 32 and 33:
Strong Inversion Drain Current (Lin
Page 34 and 35:
Strong Inversion Current and Output
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Subthreshold Drain CurrentV1 PSCBE2
Page 44 and 45:
Effective Channel Length and Widthd
Page 46 and 47:
Poly Gate Depletion EffectNgateFigu
Page 48 and 49:
Poly Gate Depletion Effect1.00Tox=8
Page 50 and 51:
Poly Gate Depletion EffectBSIM3v3.2
Page 52 and 53:
Poly Gate Depletion Effect2-40 BSIM
Page 54 and 55:
Unified Channel Charge Density Expr
Page 56 and 57:
Unified Channel Charge Density Expr
Page 58 and 59:
Unified Mobility Expression∆QVF(
Page 60 and 61:
Unified Linear Current ExpressionI=
Page 62 and 63:
Unified Vdsat ExpressionLet V ds =V
Page 64 and 65:
Single Current Expression for All O
Page 67 and 68: KAPITEL 7RESULTAT OCH REKOMMENDATIO
Page 69 and 70: CHAPTER 4: Capacitance ModelingAccu
Page 71 and 72: Geometry Definition for C-V Modelin
Page 73 and 74: Methodology for Intrinsic Capacitan
Page 83 and 84: Charge-Thickness Capacitance Modelp
Page 85 and 86: Charge-Thickness Capacitance Modelw
Page 87 and 88: Extrinsic CapacitanceFigure 4-4 ill
Page 89 and 90: Extrinsic Capacitance2( V + δ ) 4
Page 91 and 92: CHAPTER 5: Non-Quasi Static Model5.
Page 93 and 94: Model FormulationFigure 5-1. Quasi-
Page 95 and 96: Model Formulationwhere elm is the E
Page 97 and 98: Model Formulationwhere i represents
Page 99 and 100: CHAPTER 6: Parameter ExtractionPara
Page 101 and 102: Extraction ProcedureWOrthogonal Set
Page 103 and 104: Extraction ProcedureInitial Guess o
Page 105 and 106: Extraction Procedureoptimization. (
Page 107 and 108: Extraction ProcedureStep 7Extracted
Page 109 and 110: Extraction ProcedureB0, B1Fitting T
Page 111 and 112: Extraction ProcedureStep 20Extracte
Page 113 and 114: Notes on Parameter Extraction6.4.2
Page 115 and 116: Notes on Parameter ExtractionnC-1.
Page 117: CHAPTER 6: Parameter ExtractionPara
Page 121 and 122: Extraction ProcedureInitial Guess o
Page 123 and 124: Extraction Procedureoptimization. (
Page 125 and 126: Extraction ProcedureStep 7Extracted
Page 127 and 128: Extraction ProcedureB0, B1Fitting T
Page 129 and 130: Extraction ProcedureStep 20Extracte
Page 131 and 132: Notes on Parameter Extraction6.4.2
Page 133 and 134: Notes on Parameter ExtractionnC-1.
Page 135 and 136: CHAPTER 7: Benchmark Test ResultsA
Page 137 and 138: Benchmark Test ResultsIds (A)1.E-02
Page 141 and 142: Benchmark Test Resultsgm/Ids (mho/A
Page 145 and 146: CHAPTER 8: Noise Modeling8.1 Flicke
Page 147 and 148: Flicker NoiseNlC=ox( V −V− min(
Page 149 and 150: Noise Model Flag8.3 Noise Model Fla
Page 151 and 152: CHAPTER 9: MOS Diode Modeling9.1 Di
Page 153 and 154: Diode IV ModelJssw= Js0sw⎛ E⎜
Page 155 and 156: MOS Diode Capacitance Model9.1.3 Mo
Page 157 and 158: MOS Diode Capacitance Model(9.18)Cj
Page 159 and 160: MOS Diode Capacitance Model(9.26)Cj
Page 161 and 162: MOS Diode Capacitance Model(9.32)
Page 163 and 164: APPENDIX A: Parameter ListA.1 Model
Page 165 and 166: DC ParametersSymbolsused inequation
Page 167 and 168: DC ParametersSymbolsused inequation
Page 169 and 170:
C-V Model ParametersSymbolsused ine
Page 171 and 172:
dW and dL ParametersA.5 dW and dL P
Page 173 and 174:
Temperature ParametersSymbolsused i
Page 175 and 176:
Process ParametersSymbolsused inequ
Page 177 and 178:
Model Parameter NotesK2( γ1−γ)(
Page 179 and 180:
Model Parameter NotesCgdo = dlc * C
Page 181 and 182:
APPENDIX B: Equation ListB.1 I-V Mo
Page 183 and 184:
I-V ModelC C V C V D L effDL effdsc
Page 185 and 186:
I-V ModelEsatsat= 2νµ effB.1.5 Ef
Page 187 and 188:
I-V ModelB.1.8 Polysilicon Depletio
Page 189 and 190:
Capacitance Model EquationsTRdsw( T
Page 191 and 192:
Capacitance Model EquationsB.2.2.2
Page 193 and 194:
Capacitance Model EquationsQ inv= 0
Page 195 and 196:
Capacitance Model Equationsif (V ds
Page 197 and 198:
Capacitance Model Equations⎡Q W L
Page 199 and 200:
Capacitance Model EquationsVgsteff
Page 201 and 202:
Capacitance Model Equations(i) 50/5
Page 203 and 204:
Capacitance Model EquationsAbulk0
Page 205 and 206:
Capacitance Model Equations(3) capM
Page 207 and 208:
Capacitance Model EquationsδQsub=
Page 209 and 210:
APPENDIX C: References[1] G.S. Gild
Page 211 and 212:
[18] M.C. Jeng, "Design and Modelin
Page 213 and 214:
[35] K.K. Hung et al, “A Physics-
Page 215 and 216:
APPENDIX D: Model Parameter Binning
Page 217 and 218:
DC ParametersSymbolsused inequation
Page 219 and 220:
DC ParametersSymbolsused inequation
Page 221 and 222:
AC and Capacitance ParametersD.3 AC
Page 223 and 224:
NQS ParametersD.4 NQS ParametersSym
Page 225 and 226:
Temperature ParametersD.6 Temperatu
Page 227 and 228:
Process ParametersSymbolsused inequ
show all

BSIM3v3.2.2 MOSFET Model - The University of Texas at Dallas

Create successful ePaper yourself

Delete template?

Save as template?