IBM IntelliStation - ps-2

100
12. In a fault-tolerant networking environment, using the fault-tolerant software delivered with the Ethernet adapters of a single manufacturer is recommended. Installing fault-tolerant
solutions provided by multiple manufacturers may cause failures if the intermediate drivers provided with the adapters are not compatible. Two optional adapters are copper and Intel-based
(P/N 06P3601, 22P6801). Two adapters are Broadcom-based (P/N 22P7801, 31P6301).
13. The Wake on LAN (WoL) function provided by this Ethernet PCI adapter is supported in this system.
14. xSeries 345 provides three USB ports (two on the rear of the chassis and one on the front), one serial port and two RS-485 ports for system management.
15. Due to homologation variances, modem availability may differ by country. 19K4162 is supported only by Windows operating systems.
16. When installed in xSeries345, Remote Supervisor Adapter (RSA) shares functionality with the integrated service processor and serves as interface for both. RSA provides full system
management functionality through a customer-supplied Ethernet cable or modem connection or as part of an interconnected system management bus (option includes all interconnect
hardware). An external Cat5 connection between RSA and the integrated service processor using the pigtail cable and short Cat5 cable supplied with RSA is not required. The 20-pin ribbon
cable connecting RSA to the planar meets all powering and signaling requirements. Connection of the external AC power supply provided with RSA is not required.
17. Remote Supervisor Adapter II (P/N 59P2984) includes an internal 20-pin ribbon cable for connection to the system planar, an interconnect cable, a 56w AC power adapter, an intrarack
power cable and a country-specific wall power cord. External connectors include an RS230 (9-pin) serial port, 10/100 base T Ethernet port (RJ-45), interconnect port (RJ-11) and power
connector. The interconnect cable includes a single RJ-11 connector and dual RJ-48 ports. Supports an interconnect network of up to 24 RSAs or ISMPs with aggregate cable connection
length of 300ft (91.4m) or less. No more than 12 ASMPs are supported in an interconnect network. RJ-45 bus is self-terminating, i.e., terminators are not required for the interconnect bus.
18. Models 31X with 400MHz FSB support most full-size, half-length, universal-keyed PCI adapters also in slot five.
xSeries 345 Power, Monitors & Accessories
Part Number Description
Power 1
59P4057 350w Hot-swap Power Supply Upgrade2 74P4965 514w Hot-swap Redundant Power Supply (US) 3
74P4955 514w Hot-swap Redundant Power Supply (International) 3
Uninterruptible Power Supply (UPS) 4
32P1020 APC 2U Smart-UPS 1400RMB
2130R30 UPS3000XLV 5
2130R31 UPS3000XHV5 32P1692 UPS Extend Run Battery Pack5 37L6861 APC Smart-UPS 5000RMB6 Monitors7 633147N E54 Color Monitor 15in (350mm, 13.8in viewable image), stealth black8 63324HN E74 Color Monitor 17in (406mm, 16in viewable image), stealth black 8
66274AN G78 Color Monitor 17in (406mm, 16in viewable image), stealth black8 32P1031 NetBAY 1U Flat Panel Monitor Console Kit (with US Space Saver keyboard) 9
32P1032 NetBAY 1U Flat Panel Monitor Console Kit (without keyboard) 9
32P1702 NetBAY 2U Flat Panel Monitor Console Kit (with US Space Saver keyboard) 9
32P1703 NetBAY 2U Flat Panel Monitor Console Kit (without keyboard) 9
1. xSeries 345 ships with a single worldwide, voltage-sensing hot-swap power supply and two 9ft power cords. Both 400MHz models
and 533MHz FSB models with 2.67 and 2.8GHz processors use 350w Hot-swap Power Supply Upgrade (P/N 59P4057). 533MHz FSB
models with 3.06GHz processors require 514w Hot-swap Redundant Power Supply Upgrade (P/N 74P4965, 55). Power supply upgrades
include one auto-sensing cable with IEC 320-C13 to IEC 320-C14 connectors for attachment to a rack PDU or high-voltage UPS. N+N
power supply redundancy requires installation of a matching optional power supply upgrade.
2. 350w Hot-swap Redundant Power Supply (P/N 59P4057) includes a power supply, three hot-swap fans that provide redundant
cooling and one 9ft power cord for connection to a rack PDU. If a low-voltage connection is required, use optional low-voltage 14ft
NEMA 5-15P power cord (P/N 94G6667).
3. 514w Hot-swap Redundant Power Supply (P/N 74P4965, 55) includes a power supply and one 9ft power cord for connection to a rack
PDU. If a low-voltage connection is required, use optional low-voltage 14ft NEMA 5-15P power cord (P/N 94G6667).
4. For runtimes and UPS attributes see Appendix C: UPS Runtime Estimate.
5. Height is 2U. See Rack Cabinets and Options section for supported IBM racks.
6. Height is 5U. See Rack Cabinets and Options section for supported IBM racks.
7. xSeries 345 uses an integrated ATI Rage XL video controller with 8MB of memory.
8. Installation within a rack requires optional Monitor Compartment (P/N 94G7444).
9. Includes a 15in Flat Panel Monitor.