IBM IntelliStation - ps-2

36
Part
Number
Description RPM Height
Hot-swap Models Nonhot-swap Models
Bays
Supported 3
Maximum
Quantity
Bays
Supported
Maximum
Quantity
IDE HDDs1 22P7157 40GB 7200rpm ATA-100 (EIDE) HDD 7200 SL - - 4 ... 7 3
09N4226 80GB 7200rpm ATA-100 (EIDE) HDD 7200 SL - - 4 ... 7 3
09N4231 120GB 7200rpm ATA-100 (EIDE) HDD
Nonhot-swap Ultra160 SCSI HDDs
7200 SL - - 4 ... 7 3
2
06P5750 18.2GB 10Krpm Ultra160 SCSI SL HDD 10000 SL 4 1 4 ... 7 4
06P5751 36.4GB 10Krpm Ultra160 SCSI SL HDD 10000 SL 4 1 4 ... 7 4
06P5752 73.4GB 10Krpm Ultra160 SCSI SL HDD 10000 SL 4 1 4 ... 7 4
06P5765 18.2GB 15Krpm Ultra160 SCSI SL HDD 15000 SL 4 1 4 ... 7 4
06P5766 36.4GB 15Krpm Ultra160 SCSI SL HDD
2, 3
Nonhot-swap Ultra320 HDDs
15000 SL 4 1 4 ... 7 4
32P0723 36.4GB 10Krpm Ultra320 SCSI HDD 10000 SL 4 1 4 ... 7 4
32P0724 73.4GB 10Krpm Ultra320 SCSI HDD 10000 SL 4 1 4 ... 7 4
32P0725 146.8GB 10Krpm Ultra320 SCSI HDD
Hot-swap Ultra160 SCSI HDDs
10000 SL 4 1 4 ... 7 4
4
06P5754 18.2GB 10Krpm Ultra160 SCSI Hot-Swap SL HDD 10000 SL 5 ... 7 3 - -
06P5755 36.4GB 10Krpm Ultra160 SCSI Hot-Swap SL HDD 10000 SL 5 ... 7 3 - -
06P5756 73.4GB 10Krpm Ultra160 SCSI Hot-Swap SL HDD 10000 SL 5 ... 7 3 - -
06P5767 18.2GB 15Krpm Ultra160 SCSI Hot-Swap SL HDD 15000 SL 5 ... 7 3 - -
06P5768 36.4GB 15Krpm Ultra160 SCSI Hot-Swap SL HDD 15000 SL 5 ... 7 3 - -
Optical Devices
Bays
Supported
22P6950 16x Max RAM-Read DVD-ROM Drive5, 6 1, 2
10K3782 48x-20x CD-ROM Black Internal IDE Drive5 1, 2
22P6970 Multi-Burner5, 6 1, 2
22P6997 48x-24x-48x CD-RW Drive 5
1, 2
External Storage Expansion Units7 Form Factor
35311RU EXP300 Storage Expansion Unit 8
Rack (3U)
09N7296 EXP300 Rack-to-Tower Conversion Kit -
1. The xSeries 205 EIDE controllers support a maximum of four IDE devices per machine including CD-ROM drives, hard disk drives and IDE tape drives.
2. Nonhot-swap HDDs are supported in bays 4 ... 7 of nonhot-swap models and in bay four of hot-swap models. Nonhot-swap HDDs are not supported on the same SCSI bus as the hotswap
backplane in hot-swap models.
3. Ultra320 HDDs are supported, but performance is limited to the Ultra160 speed of the SCSI controller.
4. Hot-swap HDDs are supported in bays 5 ... 7 of hot-swap models. Bay four supports nonhot-swap HDDs only. Nonhot-swap HDDs are not supported on the same SCSI bus as the hotswap
backplane in hot-swap models.
5. Either replace the standard CD-ROM or install in the available media bay. A two-drop IDE cable is included with the optional optical drive (same cable is standard in the system). If installing
as an additional device, connect the cable to each optical device and the IDE connector on the system board. Configure the optional device as a master using the preset configuration if
replacing the standard device or as a slave if installed as an additional device.
6. Audio not supported for DVD-ROM drives. The drive provides data input/output only.
7. Not supported by the onboard SCSI controller. Select an optional SCSI controller then refer to Appendix D: Cables - Storage Units - Controllers to confirm the controller supports the desired
External Storage Expansion Unit and to select a supported cable. For HDD or other expansion unit options, see the specific expansion unit section.
8. EXP300 includes a single 2m Ultra2 SCSI cable and dual hot-swap 500w redundant power supplies, each with its own power cord. To convert an EXP300 to a tower form factor, EXP300
Rack-to-Tower Conversion Kit (P/N 09N7296) is required.