STX Signal Transmitter Installation and Operation ... - Kistler-Morse

More documents

Recommendations

Info

Chapter 3. Stand-Alone STX Analog Calibration and Setup Tracking can be utilized in any of the following combinations: • No zero or material tracking • Zero tracking only • Material tracking only • Zero tracking and material tracking The Material/Zero Tracking has three parameters to define its operation: Zero Tracking Window This parameter sets the maximum plus or minus offset value for zero tracking. If the minus offset value is exceeded, the STX resets the zero calibration point. The default is .00 mV — at this value, zero tracking is turned off. Refer to Table 3-16 for the positions of DS1 through DS8 and then follow the procedure in Setting Up the Parameter. DS4 DS3 DS2 DS1 Window (mV) 0 0 0 0 .00 (zero tracking off)* 0 0 0 1 .05 0 0 1 0 .10 0 0 1 1 .15 0 1 0 0 .20 0 1 0 1 .25 0 1 1 0 .50 0 1 1 1 1.00 1 0 0 0 1.25 1 0 0 1 1.50 1 0 1 0 1.75 1 0 1 1 2.00 1 1 0 0 2.50 1 1 0 1 3.00 1 1 1 0 3.50 1 = on, 0 = off, * = default Note: To select Zero Tracking Window, set dipswitches DS5 through DS8: DS8 = 1, DS7 = 1, DS6 = 0, DS5 = 1. Table 3-16. Material/Zero Tracking Zero Tracking Window Dipswitch Settings DS4 DS3 DS2 DS1 Tracking Rate (Micro V/s) 0 0 0 0 .30 0 0 0 1 .50 0 0 1 0 .80 0 0 1 1 1.00 0 1 0 0 1.50 0 1 0 1 2.00 0 1 1 0 2.50 0 1 1 1 3.00 1 0 0 0 3.50 1 0 0 1 4.00 1 0 1 0 4.50 1 0 1 1 5.00* 1 1 0 0 10.00 1 1 0 1 20.00 1 1 1 0 50.00 1 1 1 1 150.00 1 = on, 0 = off, * = default Note: To select Zero Tracking Rate, set dipswitches DS5 through DS8: DS8 = 1, DS7 = 1, DS6 = 1, DS5 = 0. Table 3-17. Material/Zero Tracking Tracking Rate Dipswitch Settings Material Tracking On/Off This parameter turns Material Tracking on and off. Refer to Table 3-18 for the positions of DS1 through DS8 and then follow the procedure in Setting Up the Parameter. DS4 DS3 DS2 DS1 Material Tracking 0 0 0 0 Off* 0 0 0 1 On 1 = on, 0 = off, * = default Note: To select Material Tracking On/Off, set dipswitches DS5 through DS8: DS8 = 1, DS7 = 1, DS6 = 1, DS5 = 1. Table 3-18. Material/Zero Tracking Material Tracking On/Off Dipswitch Settings Tracking Rate The Tracking Rate sets the threshhold in uV/sec for both zero and material tracking. When the rate of change exceeds this value, indicating that material is actually moving, the STX stops tracking until the rate of change again falls below this value. The default is ± 5.0 uV/sec. Refer to Table 3-17 for the positions of DS1 through DS8 and then follow the procedure in Setting Up the Parameter. 3-12
Chapter 3. Stand-Alone STX Analog Calibration and Setup Remote Tare The remote tare feature allows you to tare or ‘zero’ a vessel. Remote tare is useful when you want to monitor how much material is added to or removed from the vessel from a given point. The effect is as follows: • If the STX current output is in Net Mode, the current output will correspond to the change in weight since the last time the vessel was tared, rather than to the total weight in the vessel. • (if STX installed in or serially communicating with MVS) If the MVS-STX display is set to Net (by pressing the Net/Gross Key), the display will correspond to the change in weight since the last time the vessel was tared, rather than to the total weight in the vessel. If setpoints and/or current outputs are set up based on net weight, their activation will correspond to the change in weight since the last time the vessel was tared. • (if STX serially communicating with PC, ROPE, etc.) Any serial communications related to the Net weight will correspond to the change in weight since the last time the vessel was tared. Refer to the referenced drawings in Appendix H. To activate the remote tare: • Stand-Alone (TI-SP.STX-02): Short IN and +5V on TB1 on the STX PCB together for 1 second with a dry contact. • Standard 19” Rack (TI-SP.STX-03) or MVS-STX (TI-MVS.STX-01): Short Digital In and +Vout on TB2 on the Termination PCB together for 1 second with a dry contact. 3-13
Page 1 and 2: STX Signal Transmitter Installation
Page 3 and 4: Table of Contents Table of Contents
Page 5 and 6: Table of Contents Chapter 7. MVS-ST
Page 7 and 8: Chapter 1. Introduction Chapter 1.
Page 9 and 10: Chapter 1. Introduction Status LED
Page 11 and 12: Chapter 2. Hardware Installation Ch
Page 13 and 14: Chapter 2. Hardware Installation Se
Page 15 and 16: Chapter 2. Hardware Installation S1
Page 17 and 18: Chapter 3. Stand-Alone STX Analog C
Page 27: Chapter 3. Stand-Alone STX Analog C
Page 31 and 32: Chapter 4. MVS-STX Menu Tree, Keybo
Page 37 and 38: Introduction Chapter 5. MVS-STX Dis
Page 39 and 40: Chapter 5. MVS-STX Display Menu 4.
Page 41 and 42: Chapter 5. MVS-STX Display Menu The
Page 43 and 44: Chapter 5. MVS-STX Display Menu 8.
Page 45 and 46: Chapter 6. MVS-STX Inputs and Outpu
Page 59 and 60: Introduction 7-1 Chapter 7. MVS-STX
Page 61 and 62: Chapter 7. MVS-STX Calibration Menu
Page 67 and 68: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 69 and 70: Chapter 8. MVS-STX Service Menu Cha
Page 71 and 72: Chapter 8. MVS-STX Service Menu Adj
Page 73 and 74: Qlfy (qualify) Qlfy is the triggeri
Page 75 and 76: Chapter 8. MVS-STX Service Menu •
Page 77 and 78: Chapter 8. MVS-STX Service Menu Mic
Page 79 and 80:
Chapter 8. MVS-STX Service Menu The
Page 81 and 82:
Chapter 9. MVS-STX Math Channels Ch
Page 83 and 84:
Chapter 9. MVS-STX Math Channels
Page 85 and 86:
Chapter 9. MVS-STX Math Channels 8.
Page 87 and 88:
Appendix A. Product Specifications
Page 89 and 90:
Appendix B. Serial Commands Appendi
Page 91 and 92:
Appendix B. Serial Commands Checksu
Page 93 and 94:
‘m7’ Command — Select Self-Ca
Page 95 and 96:
Introduction Appendix C. MVS-STX Ca
Page 97 and 98:
Appendix C. MVS-STX Calculation of
Page 99 and 100:
Appendix D. MVS-STX Error Messages
Page 101 and 102:
5. I/O Error Adr:XX Explanation An
Page 103 and 104:
Appendix E. Trimming the Current Ou
Page 105 and 106:
Appendix F. Industry Approvals Appe
Page 107 and 108:
Appendix G. Kistler-Morse Service a
Page 109 and 110:
Appendix H. Technical Drawings Appe
Page 112:
Appendix H. Technical Drawings H-4
Page 116:
Page 120:
Page 124:
Page 128:
Page 132 and 133:
Page 134:
Appendix I. MVS-STX Menu Tree and H
show all

STX Signal Transmitter Installation and Operation ... - Kistler-Morse

Create successful ePaper yourself

Delete template?

Save as template?